User's Manual
Table Of Contents
- Feature List
- Features of SunCorp GAP DECT
- Main User interface
- Call User interface
- MENU Settings
- MESSAGE PLAY
- PHONEBOOK
- TAM SETTING
- SMS
- SETUP
- HANDSET
- REGISTER
- Answer machine features
- Base description
- Base unit operation
- Call answering and message recording
- Memory full
- Message playback
- Remote interrogation.
- Technical requirement
- Default setting data
- Setting for countries variance and type of product
- BPR detection (Branch Phone Detection)
- CPC (ECS) detection (End of call signal)
- Silence detection
- Tone detection
- DTMF detection
- AGC for recording
- Audio out put level setting
- Supervisory tone
- Tail cut
- Ring signal detection
- LED flashing
- Data storage
- Prefix dialling
- Quick default settings
- Subscribe a new handset
- Test modes
- Specifications
• During message play, messages will be paused if DTMF 2 is received. The confirmation
tone will be heard after 10 seconds, which is repeated every 10 seconds.
• While message play is paused, it will resume if DTMF 2 is received. Confirmation that the
DTMF 2 has been detected will be by the user hearing the messages.
• If a message is left paused for more than 60 seconds, all messages shall be saved (except
those deleted before the last “End of messages” prompt), and send L_beep and then line
released.
• During message play or message pause, the current message will be replay if a single
DTMF 4 is received during message play. If DTMF 4 is received during
message number
playing
will skip back to the start of previous message. Messages will be selectively deleted
if DTMF 5 is received. Confirmation that the message has been deleted will be by the unit
announcing, "Message deleted" and skipping forward to play the next message, or to the
end of message sequence described above. Messages are marked for deletion at this stage
but are only actually deleted after the line is released.
• During message play, messages will skip forwards if DTMF 6 is received. Play will skip
forward to the start of the next message.
• It shall be possible to interrupt an operation or the remote interrogation menus by sending
an appropriate DTMF signal. If the remote menu is being playback, pressing invalid DTMF
has no effect (No 4 short beeps). The menu is being played without any interrupt. After the
menu is played to end, it waits the user enter the DTMF for 8 seconds, if a DTMF instruction
is received which is not valid, then 4 short beeps will be played to line and the count down
counter (8 seconds) keeps counting down. After 8 seconds time out, the unit will send
L_beep.
• If the end of messages is reached during skip forwards, “End of messages” will be played
after the DTMF 6 is recognised.
• If the line is released by the unit for any reason prior to the voice prompt signifying the end
of messages for current replay, all messages shall be saved (
except those previously
marked for deletion).
• If the line is released for any reason after the voice prompt signifying the end of messages
but before a further replay is initiated, all messages shall be saved (except those previously
marked for deletion).
• After the line is released any messages that have not been deleted shall be saved and
indicated on the message counters.
• During remote interrogation, the handset shall display "REMOTE" flashing.
• If DTMF 7 is detecting during main menu, the unit shall announce, “Answer OFF” if the
previous setting is answer on. If the previous setting is answer OFF, the unit shall announce
“Answer On” followed by current setting OGM play.
• Any valid
message recorded before remote interrogation is attempted (successfully or not)
shall be saved and indicated after the line is released (unless deleted during remote
interrogation).
5.6.1.1 Recording and checking outgoing messages in remote interrogation
• If DTMF 8 is detected at this stage, the unit shall announce:
To play outgoing message, press 2
72 of 83