User's Manual
7 8 9 10 11 12
Weather Forecast
The radio calculates the weather forecast for the next 12 to 24
hours, and it displays the current indoor/outdoor temperature
and humidity readings.
When you power on the radio, wait for about 1 minute to
receive an outdoor signal from the remote sensor. ashes
until the signal is received, then it disappears when ready.
Note:
• If AC power is interrupted and you have not installed backup
batteries, the radio will begin searching for a signal.
• Press °C /°F to display temperatures in °C or °F.
• When temperature falls below 0°C (32°F) and the weather
is rain, the snow icon will appear.
Set the Clock
1. Press and hold TIME to enter time setting.
2. Press d/HR to set the hour, and press e/MIN to set the
minute.
3. Press TIME again to enter time format setting. Then
press d/HR or e/MIN to select 12H or 24H.
4. Press TIME to confirm and exit.
Set the Alarm
1. Press and hold ALARM to enter alarm clock setting.
2. Press d/HR to set the hour, and press e/MIN to set the
minute.
3. Press ALARM again to confirm and exit.
Alarm Options
• To activate the alarm, move the BEEP/RADIO/OFF switch
to RADIO or BEEP.
• Select RADIO if you wish to wake up to your AM/FM radio
station. º displays in radio's RADIO/TIME. Select BEEP
if you wish to wake up to a beeper. » displays in radio's
RADIO/TIME.
• At the set alarm time, the alarm sounds for 60 minutes.
Press any radio button to stop the alarm and reset it to
come on the next set day.
• Press SNOOZE/SLEEP to silent the alarm for 5 minutes.
º or » ashes in radio's RADIO/TIME display.
• To turn o the alarm, move the BEEP/RADIO/OFF switch
to OFF.
Listen to your Radio
1. Extend the antenna (for FM radio).
2. Press and hold AM/FM to turn on the radio and then
adjust the volume.
3. Press AM/FM repeatedly to select a radio band (AM/FM/
AUX).
4. The radio display always defaults to time. Press d/HR or
e/MIN to show the frequency in the display.
5. Press d/HR or e/MIN to tune a station, or press and
hold d/HR or e/MIN to scan available stations.
6. Press - VOLUME or + VOLUME to adjust volume.
7. Press and hold AM/FM to switch o the radio.
Store Preset Stations
You can store 10 AM and 10 FM stations.
1. Press and hold AM/FM to turn on the radio.
2. Press AM/FM repeatedly to select the band.
3. Press d/HR or e/MIN to tune to your desired station.
4. Press and hold PROG to enter programming mode.
MEMORY ashes in the RADIO/TIME display, and a
number indicating the preset memory location appears.
Press PROG again to store.
5. Repeat 2-4 to store more stations, or press any other
keys to quit programming mode.
Listen to Preset Stations
Press and hold AM/FM to turn on the radio. Press MEMORY
repeatedly to select a preset station. The display shows the
corresponding preset station number.
Listen to an External Audio Source
1. Press and hold AM/FM to turn on the radio.
2. Use a 1/8" (3.5 mm) audio cable (not included) to
connect the earphone jack on your auxiliary audio
source to AUX IN jack on the back of the radio.
3. Press AM/FM repeatedly until the radio's RADIO/TIME
display shows AUX to select auxiliary mode.
4. Use the controls on your connected device to control
the volume.
5. When nished, disconnect the audio cable, press and
hold AM/FM to turn the radio o.
Reset
1. Switch o the radio, remove the batteries, and unplug
the adapter.
2. Using a pointed object (such as the end of paper clip or
pen), press the RESET hole for at least 1 second to reset
the radio to its default factory settings (with 5 AM and 5
FM presets).
3. Replace batteries or reconnect your adapter and turn on
the radio.
FCC Information
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit dierent
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
Complies with the European Union’s
“Restriction of Hazardous Substances
Directive,” which protects the
environment by restricting specic
hazardous materials and products.
12A16
1201781
Printed
in China
© 2016 General Wireless Operations Inc.
All rights reserved. RadioShack is a registered
trademark used by General Wireless
Operations Inc. dba RadioShack.
radioshack.com
If you cannot eliminate the interference, the FCC requires that
you stop using your equipment. Changes or modications not
expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
Product
Digital Clock Radio with Weather
Forecast
Model
1201781
Responsible
Party
General Wireless Operations Inc.
dba RadioShack
300 RadioShack Circle
Fort Worth, TX 76102
817-415-320 0
Limited Warranty
Go to www.radioshack.com/help for details.
RadioShack Customer Relations
300 RadioShack Circle, Fort Worth, TX 76102
Place the Remote Sensor
Place the sensor on a at surface within 90 feet (27.43
m) of your radio, in an open area free from trees or other
obstructions.
To mount the sensor on a wall:
1. Select a position that is not higher than 5 feet (1.5 m) on an
outdoor wall.
2. Drill a hole at the position.
3. Thread a screw (not included) into the
hole and let it extend slightly from the
wall.
4. Fit the head of the screw into the keyhole
slot of the sensor.
Note:
• When ( and the readings
ash on the radio's OUTDOOR display, replace the batteries
in the sensor.
• Before mounting the wireless sensor, verify the radio can
receive signals from the chosen location. Move the sensor
closer if the radio does not receive any signals.
• Do not block vents. Do not submerge the sensor in water.
Avoid exposing the sensor to direct rain, snow, or sunlight.
Remove the sensor from outdoors in extreme or harsh weather.
Do not place the sensor in areas of high winds.
LED
Flashes once a minute
to indicate signal
transmission.
Vents
Keyhole Slot
1201781_UG_EN_A_102416.indd 7-12 12/13/2016 11:22:05 AM