Geneinno Intelligent Robot T1 Pro Product Name：Under water robot Model Name：T1 Pro User Manual V1.0.1 2020.12 Shenzhen Geneinno Technology Co., Ltd www.geneinno.
Disclaimer 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18.
I. Introduction Geneinno T1 Pro is a light industrial-grade intelligent underwater robot able to dive to 175m depth. CarriedA17/A7 dual cores CPU, support H264/265 ultra-HD 4K video codec, built-in 12-million-pixel class professional camera, 3000lm led fill light in front. built-in dedicated image processing DSP, significantly improve the graphics processing capabilities of various scenes, meantime, the whole machine apply industrial-grade waterproof solution. Max speed underwater is 2m/s.
Safety Guide 1. Please use our product in open water and in an environment with relatively clear water quality. Try to avoid operating in an environment with too many aquatic plants, too turbid, or very complicated underwater structures. 2. Make sure there are no dense radio devices or huge metal objects around the wireless relay and turn on the antenna correctly to avoid affecting the reception of the wireless relay signal. 3.
II. User Manual 1. APP Download Android IOS Scan QR code to download “Geneinno”APP. Open APP, Please register as a Geneinno member and log in. Search "Geneinno" in IOS APP Store or Google Play to download our APP or visit "www.geneinno.com" to download APP from "Support/APP Download" for Android phones. 2. Start Connect the two ends of buoyancy cable separately to T1 PRO and the wireless relay, and then tighten the fastening nut.
3.
III. T1 Pro Special Accessory Guideline Accessory Buoyancy Block Installation ① ① ② Align the mounting hole with the hole on bracket, with the arrow of buoyancy block upward. ② Install the wing screw through the hole, insert from the outside to the inside, and tighten the nut by hand. Note: External battery needs 4 blocks; other devices do not need to install buoyancy blocks.
Lateral Thruster Installation ① Unscrew the sealing metal cover of the extension port of the intelligent underwater robot counterclockwise. Match the slot of thruster to the slide rail in the bottom of the host, slide the thruster according to direction indicated by the arrow. ② Fix by screws when it is in right position. ③ Insert the connector of the thruster into the extension port . Tighten it clockwise.
External Battery with LED Installation ① Unscrew the sealing metal cover of the waterproof connector of the intelligent underwater robot counterclockwise. Match the slot of battery to the slide rail in the bottom of the host. Slide the battery according to direction indicated by the arrow. ② Push the tail lock to the right to lock the position of the support, the bearing does not move back and forth. ③ Push the lock in place, install the screws to locate.
IV. Recharge Guideline You can check the battery information of the host on the operation interface, also can be checked by the battery indicator light on the wireless relay. Please charge in time when the battery is low, use the standard charger and connector to charge the host, charging time is about 3 hours, wireless relay is about 2 hours. The indicator on charger showing red light when it’s charging, turn green when it finish charge.
V. Specification Host Weight 4.4kg Dimensions 390×347×165 mm Max Depth 175m（Fresh Water） Max Speed 2m/s IMU 6 axis gyro & accelerometer+3 axis Compass Depth sensor Precision ± 0.2m Temperature Sensor Precision Number of Thruster ±0.5℃ Forward/back, rise/fall, turn left/right, roll, pitch, sway (by extra propeller, changeable speed) 6 Data Storage 128GB Battery Capacity 10.8V/9000mAh/97.2Wh Max Dive-time ≥4 H Charing Time 3H Degrees of Freedom Camera CMOS 12M 1/2.
Wireless Relay Wi-Fi Frequency 5GHz+2.4GHz Antenna Dual antenna Battery Capacity 10.8V/3200mAh/34.56Wh Working 6H Charging Time 3H App Operation OS IOS 9.0 or above and Android 5.0 or Underwater Gripper Gripping Force 6kg/60N Maximum Opening Distance 60mm Total Length 559mm Length 397mm Weight 660g(air) 120g(water) Note: with buoyancy material External Battery with LED Dimensions 472mm*φ36mm Weight 1650g(air), 400g (water) Battery Parameters 4400mAh/97.68Wh/22.
VI. Maintenance 1. After each use in sea water, please soak the underwater robot in fresh water for at least 1 hour and run it in fresh water for 10 minutes 2. Keep each port and connector dry and clean, always tighten the protective cover if necessary. Salt and humidity will corrode the conductors of the connectors. Please wash with running water, and use absorbent cotton or handkerchief to wipe off the excess water. 3.
Official Media Facebook YouTube Wechat Weibo Shenzhen Geneinno Technology Co.,LTD www.geneinno.
FCC Caution. § 15.19 Labeling requirements. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. § 15.21 Changes or modification warning. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
