User Manual

ManualsBrandsShenzhen Geling Technology ManualsElectronicsWALKIE TALKIE

Walkie-talkie manual

Basic intercom operation

1. Press MENU 3S--4S to turn on the intercom

2. Press MENU button once to enter channel setting, and the channel

display pattern begins to flicker. According to the ▲/▼ Select the

channel, press PTT to confirm and exit.

3. Press MENU button twice to select the group code. Close means

no code, 01-38 means CTCSS code. 39-99 means DCS code.

4. Press MENU button 3 times to enter Vox function selection.

The sensitivity OF 1, 2 and 3 gears is optional, and the default

“OF" is off

5. Press MENU button 4 times to enter the calling tone selection

function. There are 01 to 10 sound choices

6. Press MENU button 5 times to enter the button tone selection

function. On button tone select"ON", off button tone select "OF 7.

Press MENU button 6 times to enter the starting end OF call tone

selection function. Select"ON"to release PTT will have a tone, ON

the contrary, select"OF"to have no tone

8. Press MENU 7 times to return to the main page, or press PTT to confirm

the EXIT MENU

Summary of content (6 pages)

PAGE 1
Walkie-talkie manual Basic intercom operation 1. Press MENU 3S--4S to turn on the intercom 2. Press MENU button once to enter channel setting, and the channel display pattern begins to flicker. According to the ▲/▼ Select the channel, press PTT to confirm and exit. 3. Press MENU button twice to select the group code. Close means no code, 01-38 means CTCSS code. 39-99 means DCS code. 4. Press MENU button 3 times to enter Vox function selection.
PAGE 2
The battery meter 1. 2. means the battery is fully means the battery is low Turn on/off the intercom 1. To turn on the intercom, hold it down for 3 second MENU 2. To turn off your intercom, press again for three seconds Adjust the volume 1. Press ▲ to turn up the volume 2. Press the ▼ button to turn down the volume 3. The loudspeaker volume is displayed on the LCD screen, with (01-08) levels Set the channel 1. Turn on the walkie-talkie and press MENU to select channels 2. Press ▲/▼ to set channels 3.
PAGE 3
You can use this procedure to set up an indeterminate code for each channel Note: You must set the JAM Cancel Code to 0 on an FRS radio station that uses the JAM Cancel Code in order to communicate with other FRS radio stations that do not have the JAM Cancel Code Lock the keyboard To avoid additional changes to your intercom channel, press 3 Seconds or It shows that there will be one"beep" After the lock screen, other functions are locked except the lock screen key and PTT key To unlock the intercom, pr
PAGE 4
Scan the passage Use a walkie-talkie to scan the active channels. When a signal is detected, the radio will stay on that channel for five seconds, and when there is no signal transmission on that channel, the radio will continue to scan To turn on channel scanning 1. Press 3 to 4 seconds into the scanning mode; 2. Press PTT/MENU Turn off scan mode Note: During the scanning process, press ▲/▼ to change the scanning direction Safety and precautions 1.
PAGE 5
FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
PAGE 6
distance from a properly installed externally-mounted antenna to satisfy the RF exposure requirements. • Occupational/Controlled Radio, this radio is designed for and classified as “Occupational/Controlled Use Only”, meaning it must be used only during the course of employment by individuals aware of the hazards, and the ways to minimize such hazards; NOT intended for use in a General population/uncontrolled environment.