Installation Instructions

1ProductFunction

ThisdevicecomplieswithPart15oftheFCCRules.Operationissubjecttothefollowingtwo

conditions:

(1) thisdevicemaynotcauseharmfulinterference,and

(2) thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycause

undesiredoperation.

NOTE1:ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassB

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonableprotection against harmful interferencein a residential installation. This equipment

generates uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interferencetoradiocommunications.

However,thereisnoguaranteethatinterferencewillnotoccurinaparticularinstallation.Ifthis

equipment does cause harmful interference to radio or television reception, which can be

determinedby turning the equipmentoff and on, the user is encouragedtotrytocorrectthe

interferencebyoneormoreofthefollowingmeasures:

‐Reorientorrelocatethereceivingantenna.

‐Increasetheseparationbetweentheequipmentandreceiver.

‐Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiver

isconnected.

‐Consultthedealeroranexperiencedradio/TVtechnicianforhelp.

 NOTE 2: Any changes or modifications to this unit not expressly approved by the party

responsibleforcompliancecouldvoidtheuser'sauthoritytooperatetheequipment.



1.1Remoteandcollar



(1) LowShockButton:Pressthebutton，thecollarwillemitshock

oflowpowerexceptshockswitchisoff.



(2) MediumShock Button:Pressthebutton，thecollar willemit

shockofmediumpowerexceptshockswitchisoff.



(3) HighShockButton:Pressthebutton，thecollarwillemitshock

ofhighpowerexceptshockswitchisoff.

Note:Shockbuttonwillbeworkedoncein10seconds.



(4) Vibration Button: Press the button, the collar will emit

vibrationofmuchtimesejection.



(5) SoundButton:Pressthebutton,thecollarwillemitthesound

ofbeeps.



(6) PowerButton:Shortpressthebuttontoactivatethecollar.

Longpressthebuttontoshutdownthepowerofthecollar.



PAGE 1
Product Function This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
PAGE 2
1.2 Phone Note: BLE version of phone( ios or android ) is above 4.2 The collar is controlled not only by remote, also by the apple phone or sorts of android phones. Open the app of lindopet, then start to ble scan. Show the list of lindopet collar on scanning end, select your collar and click it to connect the collar. The system show the control page and setting page of the collar until it is connected. The buttons function is the same as remote’s, but shock switch button is new function.
PAGE 3
Push the setting tab to switch to the setting page and change the sorts of settings of collar. The collar’s name can be named for your dog’s name. You can change the level of five mode( Low shock mode, medium shock mode, high shock mode, vibration mode, sound mode) and save the value into the collar. Pair mode is used to make a pair the remote and the collar. When pair mode is on, the remote can send a command to the collar to complete the pairing operation.