For DSLR Cameras U5 WIRELESS AUDIO FOR VIDEO SYSTEM English Manual
This Class B digital apparatus complies with CanadianICES-003. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT REMOVE SCREWS. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THE APPLIANCE TO RAIN OR MOISTURE. CERTIFICATION Reach R210-160181 Radio Approvals: FCC Part 15.249, FCC Part 15 B, RSS-210 (Canada), EN 300 440 (Europe), EN 301.
FCC CERTIFICATION THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. WARNING: Changes or modifications not expressly approved in writing by Xvive may void the user’s authority to operate this equipment.
IMPORTANT SAFETY INSTRUCTIONS PLEASE READ THESE INSTRUCTIONS AND KEEP THEM IN A SAFE PLACE WARNING: BEFORE USING YOUR XVIVE WIRELESS AUDIO FOR VIDEO SYSTEM, CAREFULLY READ THE OPERATING INSTRUCTIONS: 1. Observe all instructions in the U5 manual carefully. 2. Do not to perform service operations beyond those described in the U5 manual.
SAFETY INSTRUCTIONS FOR LITHIUM-ION RECHARGEABLE BATTERIES If abused or misused, the rechargeable batteries may leak. In extreme cases, they may even present a risk of: • explosion, • fire, • heat, • smoke or gas. Xvive does not accept any liability for damage arising from abuse or misuse. • Keep away from children. • Only charge rechargeable batteries with chargers recommended by Xvive. • Observe correct polarity.
FEATURES The U5 Wireless Audio for Video System can be used to send audio wirelessly from the included lavalier microphone (via the system’s beltpack transmitter)to the receiver, which can be connected to a DSLR camera or audio device. The larger U5T2 set comes with two beltpack transmitters and two lavalier microphones, allowing you to send wireless signals from two lavalier microphones or other audio sources to a DSLR camera or audio device.
U5 CONTENTS U5T2 CONTENTS USB charging cable Dual USB charging cable Dual USB charging cable 3.5 mm to 3.5 mm stereo cable Windscreen Pouch 3.5 mm to 3.
U5 TRANSMITTER: BASIC OPERATION 12 2 8 3 10 4 2 1 5 7 11 6 1 Mute button: turns off the volume of the microphone input 3 “+” and “-” gain buttons: changes the input gain level from Mic: -6 to +12dB; Line: 0 to +12dB 4 CH switch: selects the channel from 1 to 6 5 Mic/Line input mode: select “Mic” for lavalier microphone, or “Line” for other devices with more dynamic range 6 The power switch turns the unit on or off, or keeps it in hold mode.
U5 TRANSMITTER: DISPLAY 1 RF channel display: press channel switch button to select channel 2 Input gain: Mic: -6 to +12dB; Line: 0 to +12dB 3 Battery level: displays the transmitter’s battery level 1 4 5 4 Input clip: peak indicator. When the clip LED illuminates, the sound level is beyond the acceptable dynamic range and may result in distortion. 5 Audio mute: press the mute button to turn off input audio 2 3 * The brightness of the screen will decrease when the unit is not in operation.
U5 RECEIVER: BASIC OPERATION 13 1 12 9 10 11 8 3 7 2 2 T1 and T2 channel output gain: -54dB to +24dB 3 S / M switch: see page 20 4 Power status LED 6 5 Power switch: switches unit on/off, and can also be set to hold. All functions of the unit are disabled while the power switch is set to the hold position. 14 6 USB charging port: USB Micro B input 5 1 4 7 Audio output: Stereo 3.
U5 RECEIVER: DISPLAY 1 T1 RF channel display: To pair with transmitter, press the channel switch button and select the same channel on both units. 2 T1 channel output gain: change this level using the output gain controls on the transmitter 1 3 6 5 3 T1 channel transmitter battery level: The battery level of the paired transmitter is displayed after a successful connection. Only displays the U5 transmitter battery level—cannot display U3 and U4 transmitter battery levels.
LV1 LAVALIER MICROPHONE U5B BATTERY 3 1 4 2 2 1 1 Microphone capsule 1 3-pin power terminal 2 Connection cable (1.6 m) 2 Battery pull tab with 3.
2.4 GHz SPECTRUM OVERVIEW AND INTERFERENCE U5 operates on the 2.4GHz ISM band, which is utilized by Wi-Fi, Bluetooth, and other wireless devices. 2.4GHz is an open band and, as such, does not require a license to be used worldwide. Tips and Methods to Improve Wireless System Performance: 1) Keep more than 3 metres of distance between the receiver unit and other WiFi transmitters such as routers. 2) Change channels to avoid interference with other WiFi products.
QUICK START INSTALL CLIP 1 2 3 4 >10 inches 1. SET UP LAVALIER MICROPHONE a) Install mic clip on the Xvive LV1 lavalier microphone; b) Use the mic clip to attach the clip-on microphone to clothing, as desired; c) Run the mic cable to the transmitter in a way that avoids friction noise, and so that the cable and the transmitter antenna do not cross. d) The Xvive LV1 microphone has an omni-directional pickup pattern. Keep at least 10 inches away from your mouth or audio source.
QUICK START Belt 2. CONNECT TRANSMITTER Connect the 3.5mm TRS lavalier microphone cable to the transmitter 3. CONNECTING THE RECEIVER TO A DSLR CAMERA Slide the shoe mount adapter onto the camera and tighten the clamping screw to hold the receiver in place. Connect receiver output to camera input using the 3.5 mm TRS cable.
QUICK START CHANNEL CHANNEL POWER ON POWER ON 15 4. POWER ON 5. PAIRING TRANSMITTER AND RECEIVER Turn the power switch to the ‘on’ position: the display screen will light up. Set transmitter and receiver to the same channel for pairing; the green LED on the receiver will illuminate when the connection is successful. You must use different channels for T1 and T2 to avoid interference.
QUICK START 6. SETTING UP THE CAMERA AND RECEIVER • Open the DSLR camera menu and navigate to the sound recording options. • Set the audio input level control to “manual” mode. • Adjust the record level. Check the output level on the DSLR camera display. Adjust the level so that the signal is strong, but not so high that it sets off the clip light.
APPLICATION SCENARIOS TRANSMITTER TRANSMITTERS Dual-channel receiver receives audio from two U5 transmitters (connected to lavalier microphones) for interviews, two-person broadcasts, etc. 17 RECEIVER RECEIVER Dual-channel receiver receives audio from one U5 transmitter (lavalier microphone) and one U4 transmitter (mixing console or sound interface).
APPLICATION SCENARIOS TRANSMITTER OR Lavalier microphone Audio device line out RECEIVER OR Camera Audio device line in (record) Send wireless audio to recording equipment TRANSMITTER RECEIVER Use two receivers (set to the same channel) connected to two DSLR cameras to send them the same wireless audio.
TRANSMITTER INPUT MODE Mic/Line Mode Sets the input level according to the audio input device. Choose MIC for lavalier microphone, and LINE for audio mixer or other line-level audio device. Mic mode input gain is -6 to +12dB; Line mode input gain is 0 to +12dB. The preset will be saved at the mode. 19 LINE MODE MIC MODE Use with audio devices with a 3.5 mm (1/8”) output. Increasing the transmitter gain results in more dynamics. Supplies 5V of phantom power for a lavalier microphone.
RECEIVER OUTPUT MODE T1 L T1 L T2 R T2 R S MODE M MODE S (stereo) mode combines two audio inputs by panning them sharp left and right when they are sent to the camera’s mic input. The T1 signal will be sent to the camera from the receiver’s left output channel. Audio source T2 will send its audio on the right channel. Adjusting the T1 and T2 output volumes will change their respective output volumes(L/R) independently.
BATTERIES AND CHARGING The U5 transmitter and receiver each use one Xvive U5B rechargeable lithium battery. The batteries can be charged while installed in U5 transmitters or receivers;or you can use the U5C battery charger, sold separately along with three backup U5B batteries. The U5 package includes a Dual USB charging cable, which connects to any 5V USB charger adapter or other USB charging device; it charges the transmitter and receiver at the same time. Note: Turn off the power switch while charging.
INSTALL THE BATTERY TRANSMITTER RECEIVER 1. Press and hold the POWER switch to turn off the power; 2. Press and slide the battery button to open the battery compartment and install the battery; 3. Insert U5B battery into the battery compartment with the terminals facing the right way; close the compartment. Make sure the battery compartment is locked securely. 1. Press and hold the POWER switch to turn off the power; 2. Loosen the bottom clamping screw of the shoe mount adapter 3.
PRODUCT SPECIFICATIONS Frequencies 2400-2483.5 MHz Wireless Range Up to 100ft; depends on RF signal absorption, reflection and interference Dynamic Range MIC: 99dB; LINE: 107dB Signal-To-Noise Ratio MIC: 95dB; LINE: 107dB Battery Life 5 Hours (Xvive U5B battery) RF Sensitivity -86dBm Total Harmonic Distortion 0.2% RF Output Power 10 mW E.I.R.P.
TRANSMITTER Dimensions Weight Transmitter Type Housing Charging Voltage & Current Impedance Audio Input Connector Frequency Rms Phantom power Battery Battery life Antenna Impedance Antenna Type Number Of Antennas Display Input Gain control range RF output level Audio output max level 51 x 34 x 65mm 55.2g without battery Beltpack Molded plastic and cast metal 5V 2A Input 4.7kΩ (1KHz) 3.
RECEIVER Receiver Type Beltpack Dimensions 54 x 44 x 65mm Weight 53g without battery Housing Charging Voltage & Current Molded plastic and cast metal Battery Xvive U5B battery: 3.8V rechargeable Li-ion, 830mAh Impedance Output 470Ω (1KHz) Output connector 3.
LV1 LAVALIER MICROPHONE Microphone Electret condenser microphone Dimensions φ 8 × 19 mm (cable: 1.6m) Weight 13 g Directivity Omni-directional Sensitivity -32dB ±3dB Frequency response 30 Hz to 20,000 Hz Impedance 2.5kΩ ±30% Signal-to-noise ratio 75dB Current consumption 400μA Max Operating voltage 3.3V (2.5V to 10V) Maximum input Sound Pressure Level 120dB SPL U5B BATTERY Voltage 3.8V DC Dimensions 30 x 13 x 31mm Rated capacity 830mAh Weight 23g Watt hour 3.
TROUBLESHOOTING ISSUE No Sound Distorted Audio 27 SOLUTION • Check that an audio source has been connected to the input jack; make sure the microphone or line-in device is connected properly; • Turn up the transmitter input gain to an appropriate level; • Check that the mute switches on both the transmitter and receiver are off; • Ensure that the receiver’s audio output has been connected correctly to the camera or other recording equipment; • Turn up the gain on the receiver to an appropriate level; •
TROUBLESHOOTING ISSUE Voice too low SOLUTION • Turn up the camera input level; • Turn up the receiver output level; • Turn up the transmitter input gain • See pages 18-20 Signal instability: RF LED Flickering • See “2.4 GHz spectrum overview and interference”on page 12. Multiple connections • Make sure the receivers are both set to the same channel as the transmitter you want them to receive audio from.
U5 SERIES U5T2 2 Transmitters U5R 1 Receiver 2 Lavalier microphones (LV1) 3 Batteries (U5B) 1 Receiver 1 Battery (U5B) U5T 1 Transmitter 1 Lavalier microphone (LV1) 1 Battery (U5B) 29
U5 SERIES U5 1 Transmitter U5C 1 Receiver 1 Battery Charger for three U5B batteries 3 U5B rechargeable batteries 1 Lavalier microphone 1 Battery (U5B) LV1 U5B 1 Lavalier microphone 1 Windscreen 1 Mic clip 1 Battery 30
SHENZHEN FZONE TECHNOLOGY CO., LTD. 2nd floor, Building 12, Xicheng Industrial Area, Xixiang Town, Baoan District, Shenzhen Guangdong, China, 518101 E-mail: support@xviveaudio.com www.xviveaudio.
