Quick Setup Guide

ManualsBrandsShenZhen Foscam Intelligent Technology ManualsElectronics4.0 MP Video Doorbell (Wired)

V1.0

305503000478

Support email: support@foscam.com

Step 6

Use the provided wall anchors if installing in materials such as stucco, brick, or concrete. If installing

into a wooden doorframe, there is no need to use the wall anchors.

Anchors

Quick Setup Guide

Video Doorbell

Physical Description

Camera

Micro SD Card Slot

Reset

Light sensor

Microphone

Front Panel

Rear Panel

Doorbell button

Power Input Port

Type-C Port

Mounting slots

Speaker

Bottom Panel

Security screw hole

Add Device: Connection via the Foscam

App (Recommended)

It is strongly recommended that you complete the "add devices" process on

the Foscam app before the doorbell hardware is installed.

To ensure a smoother video experience on your smart phone, it is recommended that your smart

phone meet the following specications:

iOS: version 11 or higher.

Android: 4.1 or higher, using a device with a Graphics Processing

Unit (GPU).

Before You Get Started

Scan the QR code below to download and install the Foscam APP.

Note: For the best experience, please update the APP to the latest version!

1. Plug the smaller end of the USB cable into the Type-C port on the back of the Video Doorbell,

and the larger end into a USB wall charger such as your smartphone charger (DC5V 1.0A power

output recommended for faster charging). Please wait for a few seconds until you hear “Ready

for WiFi conguration”.

WiFi connection

Conrm

WiFi connection

WiFi

2. Make sure that your smart phone is connected to your WiFi router.

Foscam_1

Foscam_2

xxxxx_2.4G

xxxxx_5G

Tips: If you didn’t hear the voice prompt, press and hold reset for about 10 seconds to reset the

camera.

Tips: The camera supports dual-band 2.4GHz and 5GHz WiFi networks, so you can choose the

channel with the stronger signal to use. For example, choose your SSID: XXXXX_2.4G or XXXXX_5G.

3. Open the foscam APP and please sign up for a Foscam account, or sign in if you have one already.

4. After logging into Foscam APP, select “Tap to add a camera” or "+" icon on the upper right

corner, then select "Scan the QR code" and scan the QR code that labeled at the bottom of your

camera.

Scan the QR code, located at

the bottom of your camera

Tap + icon

Select ”Scan the QR code”

Tap to add a camera

Add Device

Scan the QR code

Search in LAN

Manually add

Scan QR Code

Model: XXX

MAC ID:000000000000

Username(default):admin

Password(default):(blank)

DDNS:XXXXXX.

myfoscam.org

FCC ID:XXXXX

IC:12558A-XX

S/N:FIAI1403000001

UID:XXXXXXXXXXX

FHD Wireless IP Camera

5. In “Add Device”, if you hear "Hello Foscam", select the checkbox and tap ”Next”, continue to

conrm that the device is in the blue fashing state and tap ”Next”. In “WiFi connection”, enter

your WiFi's password and tap "Conrm", (see illustrations on next page).

Tap + icon

Conrm

device

ashes blue

I have heard “Hello Foscam”

Add Device

Power the device on until

the device voice prompts

"Hella foscam"

Device flashes blue

Add Device

Conrm that the device is

in the blue ashing state

Enter your WiFi's password

and tap "Conrm"

Wi-Fi connection

The device will added by scanning the QR

code and sound waves.

Foscam_2.4G

2.4GHz / 5.0GHz

WiFi Password

Conrm

6. Please scan the QR code on the doorbell with the smartphone camera, then you will hear a

voice prompt say ”WiFi connecting”. Select the checkbox and tap ”Next”.

Place the QR code directly

in front of the camera

For WiFi configuration, please point the

QR code to the camera directly.

WiFi connection

I have heard the voice prompt

“WiFi connecting”

Tick the checkbox and tap “Next”

10~15cm

3.94~5.9in

Tips: Please place the QR code on the phone screen about 10 to 15cm (3.94 to 5.9in) away, and if

you encounter diculties you can try to move the screen slowly around 10 – 15cm (3.94 - 5.9in).

Step 5

Determine the mounting position of the doorbell. First check if you can reuse the existing holes in

the wall. Use the drill hole position template to mark the screw holes in the area where the

existing doorbell button was located. Place the drill hole position template at least 1.5m (59") high

from the ground to ensure that the height of the installed doorbell will be suitable, and then drill

the holes (use PH2 drill bit).

1.8m(71in)

1.5m (59in)

0.3m

(12in)

(39.3in)

Drill Hole Position

Template

Power Drill with

PH2 Drill Bit

Remove the existing doorbell button near the front door. Pull the two wires out carefully when

removing the old doorbell. Straighten the wire ends if necessary.

What's required: Dual-purpose screwdriver

Dual-purpose screwdriver

(Phillips screwdriver side)

Step 4

After removing the cover of the digital chime, use the wire connection terminal with the Power Kit

as pictured. After wiring is completed, replace the cover.

FRONT

TRANS

REAR

Remove the cover

Replace the cover

You can scan the QR code below to search and watch the power kit installation video.

YouTube

Step 3 (Optional)

Indoor chimes are generally of two types: mechanical, or digital. Normally, you only need to install

the power kit for digital chimes. However, due to the many types of chimes, if your home's

mechanical bell does not work properly when connected to our video doorbell, please install the

power kit to solve this problem.

How to distinguish between Digital Chime and mechanical Chime, please scan the following QR

code to view.

What's required: Dual-purpose screwdriver

Dual-purpose screwdriver

(Phillips screwdriver side)

YouTube

Video Doorbell Installation

Note: Make sure you have installed the Foscam App, and have scanned the doorbell QR code and

completed the "add device" process in the app before beginning the hardware installation process.

Step 1

Ring the existing doorbell, make sure it’s working and locate the place of your existing chimes in

the house.

Step 2

Shut o the master circuit breaker in your house. Turn the lights in your home on / o to make sure

the electricity in your house is properly shut o.

OFF

Note: If you're not comfortable doing it yourself, consult a qualied electrician.

Note: If the process of adding a camera fails, please reset your camera and try adding again

according to the above method.

Set name

Save

Camera added successfully

Please set the camera name:

My Camera

Camera added successfully

and the name has been set

7. Wait a few seconds until the camera noties you that the “Wireless connection succeeded”,

which means your camera has connected to your WiFi successfully. After, you can set the

camera name and tap “Save” in "Set name" interface.

Reset

Device white light flashes

Add Device

The Wi-Fi conguration is

complete, and the white

light of the device ashes

Conrm device white light ashes

What’s in the Box

1 x Type-c cable

1 x 5° Vertical angle bracket

1 x 15° Horizontal angle bracket

1 x

Power Kit

1 x Video Doorbell

1 x Mounting bracket

2 x Wire Nuts

1 x Silicone Plug

1 x Dual-purpose screwdriver

1 x Drill Hole

Position Template

1 x Thick mounting bracket

2 x Wire Extenders

1 x Quick Setup Guide

1 x

Expansion Screws

Quick Setup Guide

Video Doorbell

Summary of content (2 pages)

PAGE 1
Quick Setup Guide Physical Description WiFi connection Rear Panel Front Panel Mounting slots < The device will added by scanning the QR code and sound waves. Confirm that the device is in the blue flashing state Power the device on until the device voice prompts "Hella foscam" Video Doorbell Installation Wi-Fi connection Foscam_2.
PAGE 2
bracket if you wish to adjust the doorbell camera's field of view to cover more of one side. Optional Install A Video Doorbell Door Optional Install C 35mm(1.38’’) Mounting Screws 22mm(0.87’’) Mounting Screws 15° Door Optional Install B Other Ways to Access Your Doorbell Step 12 Press the doorbell to test the chime connection. Did your doorbell chime? If yes, it’s working! If no, check that wires are secure. Open the foscam APP again and check if you can view live video.