SHENZHEN EXCERA TECHNOLOGY CO.,LTD. Address: 3rd Floor, Block B,Jiada R&D Building, No.5 Songpingshan Road, Hi-Tech Park North, Nanshan District , Shenzhen Postal Code: 518057 Web: www.excera.com.
SAFETY INFORMATION transceivers are designed with advanced technology. Please observe the following precautions to prevent personal injury and ensure the safety of transceiver usage. 1. Keep the transceiver and accessories away from children. 2. Please do not try to open or modify the transceiver. 3. Please use correct battery and charger to avoid damage. 4. Please use correct antenna to ensure the communication distance. 5.
CONTENTS Power on the radio .............................................................................................................................. 14 Adjust Volume ..................................................................................................................................... 14 LED Indicator ...................................................................................................................................... 14 Alert Tone ........................................
UNPACKING STANDARD ACCESSORIES Carefully unpack the transceiver. We recommend you to identify the items listed in the following table before discarding the packing material. If any items are missing or have been damaged during shipment, please contact your dealer immediately.
BATTERY INFORMATION Charging Operation The battery pack is not charged at the factory; please charge it before use. Charging the battery pack for the first time or after extended storage (more than 2 moths) may not bring the battery pack to its normal operating capacity. The peak operating capacity of the battery will be reached after two or three charge/discharge cycles. The battery pack life is over when its operating time decreases even though it is fully and correctly charged and should be replaced.
BATTERY INFORMATION BATTERY INFORMATION NOTE: When charging a power-on transceiver equipped with battery, the indicating lamp will not turn into green to show the fully charged status. Only when the transceiver is switched off, can the lamp indicate normally. The transceiver consumes energy when it is powered on, and the charger can not detect the voltage when the battery has been fully charged.
BATTERY INFORMATION WARNING: ▼Do not short circuit battery terminals. ▼Never attempt to remove the casing from the battery pack. ▼Never assemble the battery in dangerous surroundings, spark may cause explosion. ▼Do not put the battery in hot environment or throw it into fire, it may cause explosion. PREPARATION Installing / Removing the Battery 1. Match the two grooves of the battery pack with the corresponding guides on the back of the transceiver, and then push it. 2.
PREPARATION PREPARATION Installing / Removing the Belt Clip Installing/ Removing the Hand Strap ■ Installing the Belt Clip: Slide the loop of the hand strap through the eyelet on the upper rear of the transceiver, then pull the entire hand strap through the loop to secure the hand strap in place and tighten the hand strap. Place the belt clip to the corresponding grooves on the back of the transceiver and secure with the provided screws.
PRODUCT OVERVIEW PRODUCT OVERVIEW 1 2 3 3 1 2 4 5 4 5 8 7 11 6 9 10 6 7 8 9 10 EP3120 U1 11 11 Antenna POWER / VOLUME Switch: Turn clockwise to switch on the transceiver, and turn anticlockwise till hearing “click” to switch off the transceiver. After switching on the transceiver, turn clockwise to increase the volume and anticlockwise to decrease the volume. Channel Selector Knob Turn the selector knob to select desired channel.
PRODUCT OVERVIEW SUMMARY NOTE: The PF1 and PF2 key's function can be defined the functions as below: Power on the radio Power on the radio: Turn on the radio by turning the Power/Volume switch clockwise till a click is heard, and you will hear a Power up beep if the dealer has set it. The radio is now in Rx mode. Side key: 1. Unassigned 2. All Alert Tones On/Off 3. Emergency Call 4. Monitor 5. One Touch Access 1 6. One Touch Access 2 7. One Touch Access 3 8. One Touch Access 4 9. One Touch Access 5 10.
FUNCTION INTRODUCTION Receive and make a digital call 1.Selecting a zone A zone is a group of channels. Your radio supports 2 zones, with a maximum of 16 channels per zone, total 32 channels. 1. Press zone key. 2. You can hear a confirmed alert tone, that means the radio switches from zone 1 to zone 2, or you can hear an unconfirmed alert tone, that means the radio switches from zone 2 to zone 1. 2.
FUNCTION INTRODUCTION 6.Receiving an All Call An All Call is a call from an individual radio to every radio on the channel. It is used to make important announcements requiring the user's full attention. When you receive an All Call: 1. A tone sounds and the green LED turns on. 2. If there is no voice activity for predetermined period of time, the call ends.
FUNCTION INTRODUCTION 2. Hold the radio verticaly 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 3. Press the [PTT] key to make the call. The red LED turns on. 4. Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone. Users on the channel can not respond to an All Call. 11.Making a Group or Private Call with the One Touch Call key The one Touch Call feature allows you to make a Group or Private call to a predefined ID easily.
FUNCTION INTRODUCTION will be no response (call) from the target radio unless you press the PTT button to initiate the call. Silent w/Voice: Radio transmits an alarm signal and is able to receive an incoming call without any audio until you press PTT button to initiate or respond to the call. Turn on/off Emergency mode by "Emergency On/Off " key. Lone Work There are two ways of initiating scan: ● Main Channel Scan (Manual): Your radio scans all the channels/groups in your scan list.
FUNCTION INTRODUCTION 2. 3. 4. 5. Press [PTT] key during hang time, red LED turns on. Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone. Release [PTT] key to listen. If you do not respond within hang time, the radio returns to scanning other channels/Setting group. Setting 1.Setting the Squelch Level You can adjust your radio's squelch level to filter out unwanted calls with low signal strength or signals with high background noise. Settings: Normal is the default.
FUNCTION INTRODUCTION 4.Battery Capacity Enquiry You can check battery capacity. Setup: The yellow LED turns on means the battery is being charged, the green LED turns on means battery capacity is full. Press "Battery Indicator" key and check the battery capacity by Beep alert tone. high power : 3 beeps medium power: 2 beeps low power : 1 beep very low power : low beeps TROUBLESHOOTING Phenomena Solution No power A. The battery may be exhausted. Recharge or replace the battery. B.
Limited Warrarty TECHNICAL SPECIFICATIONS General Digital: 400-480Mhz Analog: 400-480Mhz Frequency Range Channel Capacity 32 channels Channel Spacing 12.5KHz Phase-locked Step Operating Voltage Frequency Stability Operating Temperature Size Weight 5KHz, 6.25KHz 7.4V DC ±20% /(2000mAh) ±2.5ppm -20℃~ +55℃ 111×61×40mm (with battery pack) 247g (with battery pack, antenna) Receiving Part Sensitivity(12dB SINAD) ≤0.35μV Digital Sensitivity 0.3uV/-117.4dBm (BER 5%) 0.
Warranty Card Purchase Information Customer Name: Customer Phone: Purchase Date: Radio Information Model Number: Serial Number: Note: ● ● ● This warranty card applies to after-sale and maintenance services for the product and accessories described above. You must provide this warranty card and purchase invoice in order to get warranty services. The Company does not assume liability for damages caused by human factors. For more details, contact your local dealer.
