USER MANUAL Body worn camera
About this Guide The content in this document is for information purpose and is subject to change without prior notice. We have made every effort to ensure that this User Guide is accurate and complete. However, no liability is assumed for any errors or omissions that may have occurred. The manufacturer reserves the right to change the technical specification and accessories without prior notice. Caution Do not expose battery being placed in high temperature environment.
FCC STATEMENT : This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. RF warning statement: The device has been evaluated to meet general RF exposure requirement.
TABLE OF CONTENTS About this Guide Caution Note Introduction 1. Introduction 2. Box Contents 3. Product Overview 4. Main Menu Optional Detail 5. Operation 6. Camera setting through Camera Manager This camera is new generation video recorder of High Efficiency video coding (HEVC, H.265) and low power consumption. If you record videos by using H.265 coding format, it is suggested to download Media Player Codec Pack (check below link) to assist to play back H.265 videos on windows Media Player. https://www.
1. Introduction Thank you for purchasing this product. This camera is specially designed for video recording, audio recording and photo shooting. Please read the user manual before you start to use it. Important information: before you start to use this device, please connect it to computer through auxiliary USB cable, then camera will require password in the LCD screen.
3.
Item Description 1. Status Indicator LED Still Green: camera is in standby mode (Power on but not recording) Still Red: camera is on pre-recording mode Flashing Red: camera is recording video Flashing Yellow: camera is recording audio only 2. Charging Indicator LED Red: Charging Status Green: Camera is fully charged 3. Pogo Pin Connection port to charging dock 4. Light Sensor Detect changes of light and turn on/off IR for low-light recording automatically 5.
11. LCD Screen View camera status and playback recorded files 12.Scroll Up Button a) Hold to switch 720P and 1080P resolution b) In Menu or Playback mode, short press to scroll down next page or file c) In standby or video recording mode, hold to zoom out d) In playback mode, press to rewind video 13.
LCD Interface: 9
4. Main Menu Optional Detail To enter the setting menu: 1. Press Menu button and then enter the password. 2. Enter the password by the following commands: Press Scroll Up button to change the character to the previous letter or number. Press Menu button to change the character to the next letter or number. Press OK button to confirm and move to the next character 3. PS: The default password is 000000. After selecting the last character, press OK button to enter the setting menu.
Pre-record When on, a certain time (depend on video resolution) will be combined into the recorded video before record button is pressed to start recording; When off, video start until the Record button is pressed to start recording. Off, On Post Record The amount of the time the camera waits to stop recording video after you press the Record button. Off, 5 sec, 1 minute, 10 minutes, 20 minutes, 35 minutes Dewarp When on, video distortion correction will be corrected, with more power consumption.
Self Timer The time camera waits until taking a photo after you press Snapshot button. Off, 5 sec, 10 sec, 20 sec, 30 sec, 1 min Slides Show When on, viewing photo file will start a slideshow where each photo will be shown for around 5 seconds. Off, On Infrared When set to manual, you will need to hold Snapshot button to turn IR LEDs on/off. When set to Auto, these lights will activate automatically based on the light sensor's reading.
Auto Power off The amount of the time the camera can be idle before powering off. Off, 30 sec, 1 min, 3 min, 5 min LED Light When on, indicator LED will tell the status of the camera; When off, camera is entering covert mode On, Off White Led White Led light to offer light source Off, On Key Tone When on, camera will play a tone each time you press a button. When off, tone is disabled. On, Off Motor Switch of vibration indication On, Off Volume The volume of camera speaker.
5. Operation 5.1 Power on/off Hold Power button for 3 seconds to start up and enter standby mode; In any mode with holding Power button for 3 seconds, camera will shut down. PS: in standby / video recording / audio recording mode, short press power button , screen saver can be on/off. 5.2 Audio recording In standby mode, press audio Recording Button for audio recording. Camera will beep, and vibrate once and LED indicator on the top turns yellow and flashes.
5.7 Zoom In standby or video recording mode, hold Scroll Up button and scroll down button to zoom in and out the image. 5.8 IR night vision Under dark circumstances, infrared LED will help to record clear image or video. In standby mode, PRESS Menu button to navigate. Find option 【Infrared】, PRESS OK button to enter sub-menu: Manual & Auto, press OK button to select.
playback; PRESS scroll-Up button to rewind, PRESS Scroll-down button to fast forward, then PRESS OK button to play normally. You can fast forward or rewind 2x, 4x, 8x, 16x, 32x, 64x. 2) In photo file playback mode, hold scroll-Up button and Scroll-down button to zoom in and out the image. Adjustable is X1.0～X10.0. In the zoom in and out image, short press scroll-Up button and Scroll-down button to move the image to right or left side. 5.
5.14 USB Driver video/picture/audio files can only be deleted on your PC/laptop. After being connected to PC, password interface shows up, please enter the password (default password is 000000) Press the (ok) button 6 times, the camera will be recognized by the computer as Extra drive. User can go to camera folder and delete those files not needed. 5.15 Charging When camera battery is low, the battery icon will flash in the display, and you will hear a alert tone. When this happens, charge the camera.
5.16 WiFi AP mode - used for single device real time video review and controlling. Search “Eyescam Pro” in App Store or Google Play and download it to your phone or tablet.
Go to camera menu and Turn on “WiFi”. You will see GREEN WiFi icon on top of screen. Go to phone/tablet WiFi setting. Find out your body camera’s WiFi SSID (H22_WIFI_AP as default) and select, then input WiFi password (12345678 as default) and connect. Open Eyescam Pro and tap “connecting device” to enter camera interface.
Tap resolution window to change video resolution.
Tap setting icon to enter simple setting menu. Tap RED button to start/stop video recording. Tap PHOTO button to make a snapshot.
22
Tap “Recorder File” to view the video and photo files.
STA mode - used to view and control multiple cameras inside internal network. Operation is as below: 1, Connect camera to Cam Manager program. 2. Set “WiFi” to “ON (STA)” 3. Set WiFi parameter to same as WiFi router (enter WiFi router info and then click “Set”). 4, Go to WiFi router setting to check the body camera IP address distributed by router. (If needed, please check with router vendor on how IP address is distributed).
6. Camera setting through Camera Manager Camera setting can be changed within the menu or by Camera Manager (from BodyCam PC Software). The software is stored in camera storage. Please check page 3 to get access to it. 1, Open Camera Manager and enter password, connect and login.
2, Click “Get” to show up camera original settings. Choose target setting and click “Set”, then setting is changed. 3, Click “Enter U Disk” (upper right corner) to make camera to be recognized by PC as a folder. You can check all files from the camera folder.
IMPORTANT INFORMATION The clips and attachment studs rotate 360 degrees - The crocodile clip, epaulette clip, chest harness and shoulder harness attachment studs ALL turn 360 degrees. Slot the clip into the back of the camera then turn the clip vertically. Or you can slot the clips into the back of the body camera first, then attach the body camera to the chest or shoulder harness, then turn the body camera vertically. Reset device- To reset the device, use a small needle to jab the reset button.
