ThermoPro Remote Food Thermometer with dual Probes Model No. TP-26 Cook Like A Pro Every Time! 1. Introduction Congratulations on your purchase of the Professional Remote Food Thermometer, a programmable radio frequency food thermometer. You will now be able to remotely monitor the temperature of cooking food and the temperature inside your grill, oven or smoker from anywhere in your home. 2. Components 1 x Receiver 1 x Transmitter 2 x Detachable stainless steel probes with steel mesh cable.
· LCD (Liquid Crystal Display) – Displays all icons, temperature ，TIMER · Low battery Indicator · Remote range: 500FT (150m) · IPX4 Waterproof (Protects from splashing water, but do not submerge in water) · Temperature range of probe: 14˚F to 572˚F (-10˚C to 300˚C) · Temperature Accuracy: ±1.8˚F(±1.0˚C) in range between 32 to 212°F (0 to 100°C) · Tabletop, magnet and wall-mounted design · Battery Compartment:: 2*AAA batteries, 3.0V 4.
1、 : Press to turn on/off the receiver; Press and hold for three seconds to enter the Synchronize/Pair process. 2、PROBE/SET/ALARM : Press to rotate between Thermometer Probe 1 or Probe 2. When choose the probe, the current temperature and setting temperature will flash for three seconds. When selecting meat type or setting temperature, press to confirm. Press and hold for three seconds to close the alarm. 3、 : Press to turn on/off the backlight.
type. Press PROBE/SET/ALARM button to confirm. While in BBQ mode, press and hold for three seconds to set HI and LO temperature. 5. Transmitter Features 6. Buttons 1. 2. /℉/℃: Press to turn on/off the Transmitter. Press and hold for 3 seconds to switch between ℉and ℃. : press to turn on/off the backlight. Backlight will auto-off after 15 seconds of inactivity. 7. Installing batteries Open the battery compartment of the receiver and insert two “AAA” batteries with correct polarity.
9. Auto Off Feature The receiver will turn off automatically if it hasn’t received the temperature signal from the transmitter for more than 30 minutes, a beep will sound for one minute before it shuts down. The transmitter will automatically shut down if the temperature of the 2 probes stays below 40 ˚C for 2 hours. 10. How to Set Meat Temperatures to Preset Temps 1、Press the PROBE/SET/ALARM button to select between the probe 1 and probe 2. 2、Press MEAT/HI/LO button to activate meat type selecting.
4、Press ▲or ▼ buttons again to set the HI temperature. Press and hold the ▲ or▼ buttons to rapidly increase or decrease the temperature values. 5、Press PROBE/SET button to confirm the HI temperature and turn to the LO temperature. Press ▲ or ▼ buttons to set the LO temperature. Press and hold the ▲ or▼ buttons to rapidly increase or decrease the temperature values. 6、Press PROBE/SET button to confirm the LO temperature. And the digit will stop flashing.
3、To pause the count up timer, press the START/STOP/CLEAR button. TIMER ▲ will become solid. 4、If you wish to clear the timer, press and hold the START/STOP/CLEAR button. 15. Synchronize/Pair Transmitter and Receiver The transmitter and receiver were already paired at our manufacturing facility. Usually you do NOT need to re-synchronize or re-pair the units.
· If the temperature displayed seems to read too high or the temperature seems to increase too quickly, check to make sure the probe tip is not poking through the food. Re-position the probe tip in the center of the thickest part of food. Avoid touching bone or heavy fat areas. 17. Cautions 1. Always wear a heat resistant glove to touch the stainless-steel probe sensors or wires during or just after cooking. Do not touch with bare hands. 2.
· Wipe the transmitter and receiver with damp cloth. Do not immerse either in water. 19. FCC Compliance Information to user Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users' authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
declaration of conformity can be found at: https://itronicsmall.com/eu-declaration-of-conformity/ 21. Disposal Meaning of the “Dustbin” Symbol · Protect our environment: do not dispose of electrical equipment in the domestic waste. · Please return any electrical equipment that you will no longer use to the collection points provided for their disposal. · This helps avoid the potential effects of incorrect disposal on the environment and human health.
22. FCC Caution： This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
