User's Manual

Troubleshooting
My pet does not respond after correct installation Petrainer Rechargeable
and Waterproof Training Collar.
You need to charge the Remote Transmitter and Receiver Collar for 2 hours
individually first.
You need to turn on the Remote Transmitter by holding the mode button for 5
seconds.
Check the levels of vibration or static shock.
Make sure the Receiver has enough power to operate.
Restart the Receiver collar by pressing the on/off button.
Test 4 functions (Beep, Light, Vibration and Shock) first before using. See part
“Test” of Operation Guide.
Intensity level has to be more than “0” when pairing. Test launch for vibration
and Static Shock Function.
The Receiver Collar will go into deep sleep if no operation for 5 minutes and
any dog movement will activate the device.
Make sure the Contact Points are placed snugly against your pet's skin.
Trim your pet's fur where the Contact Points touch the neck or switch to the
longer Contact Points.
If none of the above works, you can try repairing between the Remote Transmitter
and Receiver Collar. (See part “Pairing” of Operation Guide)
Remote Transmitter does not work.
You need to charge the Remote Transmitter for 2 hours when you get product
for the first time.
Check if the Remote Transmitter is on low battery status, the symbol will show
up on the right side of the LCD screen.
You need to hold the Mode button on the Remote Transmitter for 5 seconds to
power it the device on.
Remote Transmitter automatically goes into standby mode if no action is
detected within 20 seconds, at this time there will be no LCD display. Press
any button to re-activate the Remote Transmitter.
Remote Transmitter will automatically goes into deep sleep status if no action
is detected within 2 minutes. At this time, there will be no LCD display. You have
to press “Mode” button for 5 seconds until the LCD display reappears.
-15-
-16-
My Receiver Collar works great for some time, but it does not work anymore
after I charged the device.
First, check if charging is successful, when you are charging, red LED light will
be on, after fully charged, the red led light will turn off automatically.
You have to turn on Receiver Collar again after you're finished charging.
We turned on the receiver collar and it starts to beep for 20 seconds.
Receiver Collar will beep for 20 seconds in low battery status unless it gets
charged. Charge it for 2 hours and the other functions will work after charging
is finished.
Our Receiver Collar is designed to not be knocked down, please don't knock
down the device, to avoid breaking structure and circuits.
I want to test Receiver Collar myself, but it does not work.
If you test Receiver Collar by your hand or leg, please touch the 2 electrodes
at the same time, only touching one electrode will not work.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
NOTE 1: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
(1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired
operation.
FCC Notice
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.