User's Manual

Perfecting Basic Obedience
Note: When we refer to stimulation button this will change depending on your
model, for models PET998DR, PET998DB, this will be your “Y” button. For any
other models, there should be a stimulation button for each type of stimulation
(static shock, vibration and beep).
The “Sit” Command
1. Put a separate, non metallic collar on your pet's neck above the Receiver collar and attach at
least a 10-foot leash.
Note: Be sure the extra collar does not put pressure on the Contact Points.
2 Hold the leash and the Remote Transmitter in one hand, keep your other hand free to guide your
t into a “Sit” position.
.
3 Press and hold your stimulation button, be it shock, vibration or beep. .
4 Immediately give the “Sit” command while holding down your desired stimulation button. .
5 Release the stimulation as soon as your dog sits and then give him praise. .
6 Release your dog from the “Sit” command and play. .
7 Repeat Steps 2 through 6. .
The “Come” Command
1. Put a separate, non-metallic collar on your pet's neck ABOVE the Receiver Collar, and attach a
10-foot leash. Note: Be sure the extra collar does not put pressure on the Contact Points.
2. Hold your leash in one hand and the Remote Transmitter in the other.
3. Wait for your pet to walk away from you. Once he's far enough away, press and
Stimulation Button (shock, vibration or beep) on your Remote Transmitter.
hold the
4. Immediately give the command “Come” while continuing to hold your Stimulation Button.
5. Using the leash, gently guide your pet toward you until he begins to come in your direction.
6. Immediately release the Stimulation Button as soon as your pet steps
towards you, and praise him enthusiastically.
7. Quickly move backwards as your pet begins to come back to you, praising him the entire time.
8. Praise your pet when he returns to you.
9. Repeat Steps 3 through 8.
10. Once your pet responds readily to the “Come” command several times, back
without giving a command. When your pet turns toward you, give the command “Come”
(WITHOUT STIMULATION) and praise him while you continue to back up. Praise your pet when
he returns to you.
away from him
11. Use your leash to prevent your pet from running past you. If your pet manages to run past you,
repeat Steps 3 through 8.
The “Stay” Command
1. Put a separate, non-metallic collar on your pet's neck ABOVE the Receiver Collar, and attach a
10-foot leash. Note: Be sure the extra collar does not put pressure on the Contact Points.
2. Put your pet on his bed. Hold your leash in one hand and the Remote Transmitter in the other.
3. Staying within 3 feet, walk the perimeter of the bed. Do not say anything to your pet.
4. If your pet tries to leave the bed, press and hold the Stimulation Button and give the “Stay”
command. Continue to hold the button until your pet is back on his bed. If necessary, use the
leash to guide your pet onto his place.
5. Praise your pet when he is back on his bed.
6. Once your pet has settled for a few seconds, release him and play calmly.
7. Repeat steps 1 through 5.
ENEN
-1- -2-
Note: It is best if your pet first understands the “Sit” command.
1. As soon as your pet lifts his paws off the ground to jump on you, press the Stimulation Button
and give the command “Sit.”
2. Release the Stimulation Button immediately once your pet is sitting, and verbally praise him.
Eliminating Unwanted Behavior
Jumping Up
Pets typically jump up to get attention. If you do not want your pet to jump on you, then friends or
members of the family should not encourage this behavior. That means every time your pet jumps
on someone, he should be reprimanded or redirected to an alternate and acceptable behavior, for
which he can receive praise.