User Manual
3 in1 Wireless Charaing Stand
F3 Manual
Preface:
FCC Warning
How to solve abnormal charging:
Product Details
Dear users, thank you for purchasing this
product .In order to This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.Changes or modifications not expressly
approved by the party responsible for compliance could void the
user's authority to operate the equipment.NOTE: This equipment
has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected. Consult the dealer or an
experienced radio/TV technician for help.
Radiation Exposure Statement : This equipment complies with
FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator and your body.
further understand the product,
please read this manual carefully
before use.Wish you a pleasant experience.
ยท
Charging stand
Wireless charing area for
mobile phone
Magnetic charging area for Apple watch
TWS headset charg ing area
Indicator lamp
USB-C
interface
1
4
5
2
3
Put the TWS headset that supports wireless charging on the
corresponding charging area for wireless charging.
The red light is on when the power is turned on, and goes out
after seven seconds.
Charging the watch, the indicator light is off.
When charging the TWS or Phone, the indicator lights up green.
Using instrucyions:
Power connected ,the device enters the standby state;
Place the Apple Watch in the
Magetic charging area to conduct
wireless charging;
Put the
mobile phone that
supports
wireless
charging on the
corresponding charging area for
wireless
charging.
Please confirm whether your mobile phone has Wireless charging
function before use;
Check whether the phone deviates from the wireless inductive
charging area of the charger;
Whether a non-metallic protective
case is used for
charging mobile
phones, and the thickness of the protective case is recommended
not to exceed 4mm;
When metal objects touch the charging area, the charger will
automatically identify and
provide power off protection.
When the
temperature of the charger is too high, it will automatically
start the
protection.
Please
unplug the power
supply first and use it
after the charger recovers the temperature.
Q & A:
Q:Why is there heating in the charging of wireless charging
inductive
products?
A:During the charging process, there will be a certain loss of
magnetoelectric conversion, which will be converted into heat,
causing the mobil
e phone and charger to generate heat, which
is a normal phenomenon.
Safety Notes
Specifications
Use indoor or under dry environment, avoid placing or using in
the environment of high temperature, humidity, strong static
electricity and strong magnetic field;
For your
safety, please do not use wet hand plug and unplug
electrical
appliances;
Avoid
putting
it in a place
easily
accessible
to infants and children;
Do not use the product if it is contaminated with water or dirt;
Non-
professional
personnel are not allowed to open and repair
without authorization.
model: F3
Interface: USB-C
Input : 9V/2A
Watch magnetic charging
output
: 3W
Mobile phone magnetic charging output: 10W Max
TWS
headset charging output : 5W Max
Material: Aluminum alloy
Size: 142*75*10MM
N W:175g
G W:301g
Suggestions:
When the device is fully charged, disconnect it from charging in
time to avoid a long cyde of charging,
which may lead to continuous
heating of the device and charger;
It is recommended to stop running the background software when
charging the phone.
1
4
5
2
3
Made in China
1 2 3