MMC-2611CA Paging Host User Manual
Content Content.................................................................................................2 Summary ............................................................................................3 Appearance.......................................................................................... 4 Parameter............................................................................................. 5 Main Functions..........................................................................
Summary MMC-2611CA works with all MMCall call buttons. It sends alphanumeric message to pager MMC-NC-8E. The functions are: wireless alphanumeric message paging, wireless deletion, duty repage, dispatch, urge dishes, monitoring function, USB data download and program update etc. It is suitable for restaurants, hotels, banks, bars etc.
Appearance 2.
Parameter 3.1. Parameter Category Parameter Dimension 220mm * 150mm * 65mm Power supply 12V/ 1.5A Communication mode USB,RS485, Ethernet and interface type Outside Indicator Power supply,RX,TX Transmitting frequency 433.500MHZ（frequency customization available） Receiving frequency 457.575MHZ（frequency customization available） Paging No. in cache 40 Repage No.
Capacity Call button——2000 Pager ——500 Palm transmitter——99 Message length 48 digits or letters Signaling standard POCSAG，numeric, english and chinese message supported Temperature -0℃—+65℃ Table 3.1 Paging host parameter list 4. Main Functions Main functions are as following： 1. Wireless receiving function. The host can receive the signals from call button and palm transmitter with feature code, and transmit the message to corresponding pager. 2.
4. Repage function. Repage times and interval can be setup between the waiter and his directors. If repaging is not finished yet while you cancel it, the message already sent will be automatically deleted. 5. Palm transmitter can be used for dispatching or urging dishes function. 6. Software sending message function. With computer software, the preprogrammed message can be edited to page the programmed pager for interior staff management. 7. Monitoring function.
Software setup Before using the paging host, please first setup the host parameter, pager, call button and palm transmitter. Use the CA software to edit and download the information. The software communication with the paging host is USB mode. Notes: While using, USB can not power on the host, so please connect it with power supply. Otherwise the transmitting and receiving function can not be used. 5.1 Function Introduction The software interface as picture 5.
As picture 5.2 shows, it’s mainly the database operation, including New file, Open, Save as, Delete and Exit. Notes: There should be a database while using the software. For the first time use, it’s necessary to setup a new database, you can choose TA or CA database. The two kinds of database are not compatible with each other. Picture 5.2 File 2. System Setup System setup including initialization, host parameter, program update, call type registration and pager check time. Picture 5.
Host parameter as picture 5.4, room No. Switch is temporarily invalid, the monitor function needs to work with monitoring software, it can be setup as transmitting data, USB passback, net page passback(customization required), among which transmitting data monitor needs to setup pager receiver No., other modes do not need to setup the No. Repage setup, it can setup the pager and its director repage times and interval.
It can correct the pagers’ time through the the software. Just click it and the pager time will the same as the time of computer. Notes: For this function, you need to setup group ID, and setup this group ID pager number as 0. （4）Call Type As picture shows, call button type setup, is to edit the multi-key buttons while registering them. Under this option, the call type can be edited and after one key call, the software will automatically show the preprogrammed type. E.g.
（5）R100/600/800 R100/600/800 is compatible with TA/CA. It works as a pager. And through the software to setup the alert way of them.
Network parameter setup as the above picture shows, you can choose to use the web function and the mode of web host or sub-host. If it’s used as web host, the host will transmit all the valid data which is paged by all the sub host, and the web sub host will upload all the data which are going to be paged to the host. If the sub host does not use the transmission function, then the transmission mode can be modified as 485 output.
many hosts, the ID of each host is different. IP: it’s the host IP, if this host works as web host, then its IP is the web sub host IP COM port: The host COM port.
Picture5.5 Read Data 4 Download Data Each time there is information modification in the host, please remember to download the data to the host. The host won’t automatically update the data. Picture 5.6 Download data Download palm transmitter information： a)Urge dishes mode setup: (1) Use the urge dishes mode: tick it, this function can be used.
(2) Numeric to English: tick it, the call button No. will be transferred to english name while sending the message. (3) Message prefix and suffix: if tick “Use the urge dishes mode”, when press button No. XX through the palm transmitter to urge dishes, the host will automatically organize the message and send, the format is: prefix+ call button No.
Notes: In dispatch mode, you have to input at least 3 digits then press # to send it correctly. 5.2 Edit Function 5.2.1 Pager Registration Pager list as picture 5.6, No. is the pager No., which ranges from 0~199, ID code is the pager ID, which should be the same as the one in the pager; pager address ranges from 8~2097152. If you choose automatically added one, then after you add one pager ID, it will automatically add one. Type is to show different pagers that can work with the host.
Picture 5.6 Pager List 5.2.2 Palm Registration As picture 5.7, this part is for the customers who use palm transmitters. The palm No. for TA is 0~9, for CA is 0~99. There are two ways to add feature code: if automatically add one is chosen, you can manually input the feature and click add, if not chosen, after press Add, within 5 seconds, edit any message on palm transmitter and send it, then the software will automatically add and decode this palm’s feature code.
Picture 5.7 Palm Transmitter List 5.2.3 Call Button Registration In call button registration list, there are manual and automatic registration. Manual Registration needs to input the feature code manually while automatic registration will automatically upload the feature code. Button No. is from 0-1999, name means the name of room where the button locates or where to serve. After registration, the message content can be edited.
total 4 pagers, 2 directors and 2 managers. Notes: Under the registration list of one call button, the pager type has to be the same. 5.8 Call Button Registration 5.2.4 Manual Send Data Manual send data is for the computer to control and send messages. Pager No. And paging message can be input and edited by the software. After click send, if there is successful prompt, it means this edited message is valid, otherwise invalid. Pager No.
5.9 Manual Send Data 5.2.5 Data Download 1. Pager parameter Download pager parameter 2. Call button parameter Download call button parameter 3. Palm transmitter parameter Download palm transmitter parameter 4. Palm transmitter setup information 5.3 Call Function Introduction 5.3.1 Call Button The call button has to be first registered before using. The pager type has to be the same under one call button registration. 1. Edit alphanumeric pager NC-8E E.g.
NC-8 to be paged. Cancel: name (table 1), content（needs service），input the number of NC-8 to be canceled. And the final type must be: delete repage. Then download the call button list to the host. When you press call, the pager will show as table 1 needs service; when you press cancel, the message will be automatically deleted. 2. Edit coaster R100/R600/R800 Under this item, name and content can not be used, only the pager address, repage or not, delete repage etc.
5.3.3 Palm transmitter paging 1. If palm transmitter pages numeric pager Under urge dishes mode: the pager will display A+ Palm No., the palm transmitter will send the call button No. Under dispatch mode: the pager will display B+ Palm No., the palm transmitter will send data content. 2. If palm transmitter pages coaster R100/R600/800 It will send the data format according to the coaster type, then the coaster will ring. 3. If palm transmitter pages NC-8E Please refer to chapter 5.1-4.
pager. 3). Duty repage The duty repage schedule is as following: Press CALL, the button will repage as the preprogrammed schedule(such as 20 seconds, repage three times), if it sill has not been canceled by the CANCEL button, it will start repaging the director, still as the preprogrammed schedule(times, interval), if still not been canceled, then it will repage the superior director, after one time page, the whole repage process ends.
waiter will receive the message and go to fetch dishes. b. Program the transmitter and host to dispatch mode(B mode), input a three digit number of the pager and maximum 5 digit table No. One palm, then press SEND to send this table message to waiter pager to dispatch the waiter serve for that table Notes: In this mode, the pager number has to be three digits, such as, No.1 please input as 001. Table No. can be from one to five digits, such as 1, 01, 001, 0001, 00001 which all means table No. 1. 6).
The host can be operated through communication, No outer power supply, USB power can just USB download or read the data,wireless operation is but after not supported press call button, the RX light does not shine.
