GYROSCOPE NAVIGATION ROBOTIC VACUUM CLEANER WITH WIFI WITH INTELLIGENT WATER TANK FOR WET MOPPING Thank you for purchasing the product. Please read through the Instructions before use.
Table of Contents + Safety, + Functionality Overview. a Advanced Features Summary. + Pans include + Examination * Before You Start. ie Brush Installation. b. Charging Dock Suety ¢. Charge Robot . d. Remote Battery Installation. + Cleaning Options. a Cleaning b. Wet Cleaning. + Feature Installations. a Installation of the Large Dust Bi b. Installation of tha Trailing Bar and Moy c. Instillation of the Tank. d. Seeing the Intelligent Tank + Advanced Cleaning. + Finishing a Cleaning Session.
Safety Before using product , read the following safety instructions and follow routine safety precautions. Oppositions to this manual may result in harm to the user or the product. This product contains a rechargeable lithium battery. The product and battery must be disposed of properly. Discarding in a landfill or dumping ground can result to hazardous substances being leaked into the groundwater. WARNING A * Only certified service technicians may disassemble, repair or modify the product.
Functionality Overview Congratulations on your adoption of Robot, your new personal cyborg. Robot is an intelligent and independent robotic vacuum who's avid about self-cleaning and disinfecting floors including tile, vinyl, wood, linoleum and low-pile carpet. For the best performance, take a few minutes to read this manual. Robot possesses many advanced features and is ready for any task you may ask of him. Advanced Features Summary Easy automatic cleaning push to start button for all ages.
Parts Included Robot x 1 Charging Dock x 1 Mop Pad x 2 Cleaning Brush x 1 (Attached on large dust bin.
Examination Robot Top View Recharging Signal Side Brush——@, — Side Brush Panel DC Recharging Port Power Switch Cover Exhaust Filter
Robot Bottom View Cliff Detector Universal Wheel Recharging Pole Side Brush Side Brush Roller Py C I Sweeping Brush > Bracket Wheel * * Wheel . .
Robot Bottom View with Mopping Accessories 0 Robot comes with one of the mop pads and the trailing bar already installed. The trailing bar's main function is to attach the mop pad to the robot and is located underneath the mop pad.
Automatic Cleaning Press this button while in standby mode and the robot will begin to clean. Press this button while the robot is cleaning to stop the cleaning session. This button blue light is normal on means the robot is working. WIFI Button Press and hold this button while in standby mode and you can hear a sound “DI” the robot will enter WIFI mode.
Remote 3 Schedule-Press this button and the robot will enter @ schedule mode. @ Return Home Press for the robot to stop cleaning and return to the charging dock. Forwardness while cleaning and the tabor will move in a forward direction. Backwards Press while cleaning and the robot will move in a backwards direction. @ Left Press while cleaning and the robot will turn in a circle to the left. > Right Press while cleaning and the robot will turn in a circle to the right.
Before You Start The following steps must take place before a cleaning session is to furnace. 1. Side Brush Installation 1. Ensure that the robot's power is off. Tum off the power by flipping the power switch on the side of the robot. 3. Position the side brush with the square hole pointed down and the brush bristles angled up. Align the square hole on the underside of the side brush to the square spoke located inside the hollow semicircle next to the universal wheel. Push down until a click is heard.
2. Charging Dock Setup 1. Place the charging dock in a position flat on the ground with the back pushed up against a wall. There should be no other objects or obstructions two meters in front of and one meter to the left, right and above the charging dock. 0 If the IR signal emission window is blocked, the robot will be unable to locate the charging dock station. 2. Connect the power adapter to the power adapter jack on the charging dock. 3.
-The cord should not be on the ground or obstructing the charging dock as it will result in the robot being unable to find the charging dock. -The charging dock should always be plugged in to ensure charging when needed, 0 Robot might have difficulty finding the charging dock in a larger room or arum full of obstacles. 3. Charge robot 1. Setup the charging dock using the “Charging Dock Setup” steps. 2.
4, Charging Charging 0 Leave the robot on the charging dock for at least B hours before the first cleaning session. After the first cleaning session, allow robot to charge for at least 16 hours before reuse. 5. Robot is ready for use and has a battery life around 90 minutes. Robot can also be charged by connecting the power adapter to the DC recharging port on the side of the robot.
-The average charging time between cleanings is around 3 hours. -The battery will not be at its full potential until after 2 to 3 cleaning and recharging sessions. -If the robot is not used on a regular basis recharge the robot once a month to maintain the battery. 4. Remote Battery Installation 1. Remove the battery cover located on the backside of the remote. 2. Place two AAA batteries in the compartment in the correct polarity. -Batteries are not included in the packaging. 3.
Cleaning Options Robot possesses two distinct cleaning methods: dry and wet cleaning. The dry cleaning method involves a vacuum sweep cleaning perfect for both hard flooring and low-pile carpet. Robots strong suction will trap debris, hair and allergens. On the other hand, the wet cleaning method showcases a vacuum and mop cleaning perfect for all hard flowerings. With a programmable tank to protect floors, Robot will vacuum and collect dirt and debris seconds before mopping.
Wet Cleaning Vacuum and Mop Cleaning -A duo cleaning between the vacuum sweep method and the wet mop. Robot collects dirt and debris seconds before mopping. With two programmable seeping modes available to protect flooring types. -Block robot from carpet and rugs while using this method. 1. Setup the charging dock in an approved position (see “Charging Dock Station Setup” on page 14). Ensure the power cord connected to the charging dock is not laying on the ground. 2.
Feature Installation Installation of the Dust Bin Sabot lly comes with the dust bin installed. 1. Pull up at "Pull" position on the top cover of the robot for the cover to open and expose its containment. 2. Lift the handle on the dust bin to lift the whole container. Insert the dust bin with the filter facing the exhaust filter of the robot and the handle exposed. 3. Lower the cover until it returns to its preexisting position and a click is heard.