Product Description

ManualsBrandsShenzhen CHT Technology ManualsElectronicsWireless Procontroller for Switch

Shenzhen CHT Technology Co., Ltd.

Rev:1.4

 first page A total of 7 pages

Bluetooth Handle Product Specifications

1. Product description:

This product belongs to Switch Pro Bluetooth game controller. It is connected to Switch host

through Bluetooth communication and supports wired connection.

2. Product Features:

(1) Include all the buttons and corresponding functions of the original Switch handle, and

increase the function of adjusting continuous speed and motor vibration strength;

(2) Provide 4 LED status indicators;

(3)20 function keys input, "docking" button to facilitate the first pairing and shutdown;

(4) Built-in double motors, high precision 3D rocker;

(5) There are 4 mapping keys M1, M2, M3 and M4 on the back, with two groups of functions to

choose from;

(6) Equip with 6-axis gyroscope, fast and accurate target locking;

(7) Compatible with PC host and support X_INPUT mode.

Summary of content (9 pages)

PAGE 1
Rev:1.4 Shenzhen CHT Technology Co., Ltd.  first page A total of 7 pages Bluetooth Handle Product Specifications 1. Product description: This product belongs to Switch Pro Bluetooth game controller. It is connected to Switch host through Bluetooth communication and supports wired connection. 2.
PAGE 2
Rev:1.4 Shenzhen CHT Technology Co., Ltd.
PAGE 3
Rev:1.4 Shenzhen CHT Technology Co., Ltd.  first page A total of 7 pages 3. functional description 4.
PAGE 4
Rev:1.4 Shenzhen CHT Technology Co., Ltd.  first page A total of 7 pages 15. The channel light flashes when the adapter is inserted, and then the channel light goes off when it is fully charged. 16. When the handle is charging on line, the corresponding channel light will flash slowly and light long after it is full. 17. 5. Low power alarm 18. When the battery voltage of the handle is lower than 3.
PAGE 5
Rev:1.4 Shenzhen CHT Technology Co., Ltd.  first page A total of 7 pages below:  (1) Select the item "Change grip/order" again, as shown below: (1) Click "Change Grip/Order" to enter, and the matching interface as shown below will appear. At this point, long press the "docking" button of the handle for 3 seconds for pairing. Four LED water lights will flash, release the "docking" button, and wait for 5:Factory calibration of handle gyroscope inductor 5 to 30 seconds.
PAGE 6
Rev:1.4 Shenzhen CHT Technology Co., Ltd.  first page A total of 7 pages In the joystick sleep state, first hold down the left 3D rocker (L3 key), and then press "R" key. The channel light will light up and flash left and right, and the joystick will enter the gyroscope sensor factory correction mode.Place the handle on a flat table and press the "+" button. After release, the 4 channel lights will light up and all will be off in 3 seconds.
PAGE 7
Rev:1.4 Shenzhen CHT Technology Co., Ltd.  first page A total of 7 pages interface, please follow the instructions on the screen to complete up, down, left, right and circle correction actions.The joystick correction interface is as follows: Handle firmware upgrade (1) If some functions of the gamepad cannot be used or the functions of the gamepad need to be updated due to the upgrade of the host system, you can upgrade the firmware of the gamepad through PC. Double click "SwtichPro_Updatavx.x.
PAGE 8
Rev:1.4 Shenzhen CHT Technology Co., Ltd.  first page A total of 7 pages During the upgrade, keep the connection of data cable stable. After a few seconds, the upgrade will be completed.
PAGE 9
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.