User's Manual

-04--03-
-06--05-
<OYOUT USER MANUAL
Bluetooth Connecting Operation
To avoid mis-pairing with other devices, please locate your Vision 650 and the device that
you wish to pair it with as close as possible (best within 1 meter).
Press and hold the Power ON button for 5 seconds, until the green and red LED flashes
alternately. Vision 650 is in pairing mode now.
Search for Vision 650 using your phone or other device.
Select “Vision 650" form the list of devices discovered from your phone or music reader.
Follow the onscreen steps to confrm the selection.
Multipoint pairing allows Vision 650 to be connected to two devices at once, allowing
user to Seamlessly transition between the two.
1. Start with your headphones off.
2. Press and hold volume- until Audrey says “Pairing” and the LED light flashes red and
green.
3. Press and hold the multifunction button and volume- button for 3 seconds. Audrey
says“Multipoint Enabled”.
4. Open your first device’s Bluetooth menu and select “Vision 650”, Audrey says
“Connected”.
5. Turn off your headphones.
6. Re-enter Pairing mode by pressing and holding volume- until Audrey says “Pairing” and
The LED light flashes red and green.
7. Open your second device’s Bluetooth menu and select “ Vision 650”, Audrey says
“Connected”.
8. Turn off your headphones.
9. Turn on your headphones , Your headphones are now connected to both devices.
1. Start with your headphones off
2. Enter pairing mode by pressing and holding volume- until Audrey says “Pairing” and the
LED light flashes red and green.
3. Press and hold the multifunction button , volume- button and volume+ button ( all
three buttons) simultaneously for 3-5 seconds, until you hear two beeps or fee vibrations.
4. Turn off your headphones . Vision 650 is now reset and can be re-paired to your device.
Remove Bluetooth connection:
Power off your Vision 650.
Place your Vision 650 out of the Bluetooth sensing distance of the paired device, select
the disconnection function on the paired device, and follow the procedure.
Answer the phone
The Vision650 has an answering phone feature. When there is an incoming call, press the
answer button to answer the call.
Please Note:
Some models of phones or music devices also may require you to insert a password. In
this case, please enter the passkey “0000” (four zero). When pairing is successful, the green
LED will flash slowly. In the future, you will not need to pair again. You will only have to
follow the normal power on procedure.
<OYOUT
USER MANUAL
<OYOUT
USER MANUAL USER MANUAL
Volume down/Power button (B); Volume up Button (C)
Disposal device cannot be turned on
1. If the device cannot be turned on, please plug in the USB twice, the red light will be
bright and the device will return to normal.
2. If the device is still unable to start up, please consult the after-sales service.
Multifunction Button(A) How to reset your headphones
Multipoint Pairing
<OYOUT
Function
Power on
Power off
Mute
Check battery status
Adjust volume
Pairing Procedures
Your new Vision 650 can be connected only to mobile phones, music readers, GPS
navigators and other devices that are equipped with Bluetooth communication system.
To achieve wireless connection with your Bluetooth mobile phone, it is necessary to
make an initial setting operation called “Pairing”.
The Pairing process is required only when the product is used for the frst time . From the
second time on, when you push the power switch, “ON”, some phones will reconnect
automatically while others will show the message, “Do you want to connect with Vision
650?” If you see this message, you must push “OK”.i
2+*/TJOIGZUX
Solid red
Solid green
Flashes red and green
Flashes green
Flashes red every 2 minutes
Charging
Charging complete
Pairing mode
Incoming call
Low battery
Action
Click one
Double-click while music is playing
Click one
Click one to switch between callers
Press and hold for 2 seconds
Press and hold for 2 seconds
Press and hold for 2 seconds
Double-click
Prompt/Audrey says"
One beep
One beep
Two\ One beep
One beep
One beep
Two beep
Device beep
"Last number redial"
Prompt/Audrey says"
"Welcome to the voice world"
"Goodbye"
"Mute on"or”Mute off"
"Battery high, Battery medium
Battery low, charge me"
One beep
Action
Press and hold volume- for 3 seconds.
Press and hold volume- for 3 seconds.
Press and hold both buttons for 2 seconds while
on a call
Click the volume up or down button while music
is paused
Click the volume up or down button to adjust
volume
Function
Play/pause music
Skip to next song
Answer/end call
Answer call waiting and put the current
caller on hold
Answer call waiting and hang up on current
caller
Reject a call
Prompt device assistant
Redial last number