Operating Instructions

LED cabinet light CS6
1.Clean the place where you intend
to attach the LED strip
Stripsize:L500*W8mm
Lumen:1500lm
1
2.Pull the paper from the adhesive
tape on the back of the LED strip.
3.Stick the strip on the intended position.
(Before install, Please check DIY Connection .)
4.Connected the led strip with controller, then connected
controller with adapter, plug in the adapter , turn on the light.
Total: 6 PCS strip bar
Wattage:16W
16-keyRFremote.Battery type: CR2025, 3V. Function as below:
ON/ OFF button: Turn on/ off light.
Increase / Decrease the brightness, total 10 levels.
25%,50%,75%,100% brightness output.
SOS button：
Breath button:
Night light button: 10% brightness output.
Timing button:
3 slow fade change - 3 fast fade change -repeat.
Max brightness fade to 10% - fade in 100% - repeat.
light will turn off after 3 / 5 / 15 / 30 / 60 minutes.
Clean timing button:
The light will flash once and the timing is cleaned.
4 hot buttons for brightness selection,
1
2
LEDController:
150 mm
Firstsecond
third
1.Click the button to turn on/ off light.
2.Press the button to adjust the brightness, the brightness will go down,
then up to MAX.
button
indicator
Notes: The strips and controller are backed with strong adhesive tape, Before install,
Please make sure the intended position is clean, oil-free, dust-free, dry.
e
*The user of the product must have read and understood these original
operating instructions prior to its first use in order to safely implement
this device.
*Please comply with all safety instructions! If you disregard any of the
safety instructions you may place yourself and others at risk.
*Store all operating information and safety instructions for future reference.
*This product is not designed for commercial use.
*This product is not a toy and should not be played with children.
*Never open any of the electrical parts or insert any kind of object into them.
*This product is battery powered, never throw it to fire or water, the battery
may explode.
*Do not expose the product to high temperatures or moisture, the product
may be damaged.
*Please do not look straight at the LED chip, it may cause your eye
uncomfortable.
Safety instructions
Technical Data
CRI > 80
IP Rate: IP20
LEDs: 30PCS /bar
Color temperature:2700K
Function
1
2
3
4
5 6 7
5
straightconnector
170mm
1.Use it to connect two LED strips, go through the spacer.
Depending on the length of the spacer, 2 to 5 PCS of this connector
can be connected together.
* There are some adhesive tapes for connectors in this kit.
2. Work as corner connectors:
Firstly backed 2 adhesive tapes to each end of the connector， then
bend it by corner, stick connector on, connect with other led strips.
Adhesive tape
Adhesive tapeAdhesive tape
a.Option1 ( length: 1.5 meter):
+
+
-
+ + +
+
+
-
+ + +
+
+
-
+
+
-
+
+
+
-
+
+
+
-
+
+
+
-
+
+
+
-
+
+
-
+
+
+
-
+
+
+
-
+
+
+
-
+
+
+
-
+
c.Option3(Length:1meter):
b.Option2(Length:3meter):
also can be connected directly
+
+
-
+ + +
+
+
-
+ + +
+
+
-
+
+
-
+ + +
+
+
-
+ + +
+
+
-
+
+
-
+ + +
+
+
-
+ + +
+
+
-
+
+
-
+ + +
+
+
-
+ + +
+
+
-
+
+
-
+ + +
+
+
-
+ + +
+
+
-
Strip 1 Strip 2 Strip 3
Strip 6 Strip 5 Strip 4
Strip 1 Strip 2 Strip 5 Strip 6
+
+
-
+ + +
+
+
-
+ + +
+
+
-
+
+
-
+ + +
+
+
-
+ + +
+
+
-
Strip 1 Strip 2
+
+
-
+ + +
+
+
-
+ + +
+
+
-
+
+
-
+ + +
+
+
-
+ + +
+
+
-
+
+
-
+ + +
+
+
-
+ + +
+
+
-
+
+
-
+ + +
+
+
-
+ + +
+
+
-
Strip 4 Strip 3
Strip 5 Strip 6
DIY Connection
“U” style connector
6
InstallationAdditional function
If you have several kits, you can use one remote to control all the kits
by "match" function. Just use one remote to re-match all the controller.
Howto"re-match"remotewithcontroller?
After plug in the power, turn off the light(the power is still on),
then press the button on the controller to go into the "match" status,
press the on/off button on the remote at the same time.
The controller will be matched with the remote.
When controller is in "match" status, the strip will flick.
When "re-match" is done, the strip will change to constant on mode.
*When you want to control multiple LEDcontrollers with one remote,
make sure that multiple LEDcontrollers are within the control range
of the remote control. Mostly the rang is 15 meters(Barrier free).
*If the remote doesn’t work, please re-match with the controller.
otherwise the battery built-in remote ran out, please replace the
battery, the battery type is CR2025.
74.00 mm
100.00 mm
A ⾯
B ⾯
3
Output:DC12V*2A
FCC Warning
This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any inte rference
received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interferenceto radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Manufacturer: Shenzhen Bason Electronics Technology Co., Ltd.
Address: 5/F., Bldg B, Huilongda Industrial Park,Shiyan Street,
Baoan,Shenzhen,China
FCC ID: 2AYVG-RM006