DOG TRAINING COLLAR User manual Model:BC201 Please read the manual carefully before use
OVERVIEW The dog training collar has been proven safe and effective through long-term market validation and customer feedback. It can help you control and train your dog within the effective range, through functions such as sound reminder, vibration warning, static shock punishment, etc., to stop barking, correct dog running, easily recall, and prevent dog picking and eating garbage outdoors and other complex training can also be carried out by remote control.
BUTTON INTRODUCTION 1 Static shock button: Press this button and the receiver will emit static shock signal; press the +/- button will reduce and increase the static shock level. 2 Tone button: Press this button and the receiver will beep; Press the +/- button will reduce and increase the sound level. 3 Signal channels switch button: With 3 channels to switch, the remote can connect the 3 receivers at the same time and also individually.
HOW TO PAIR THE REMOTE AND RECEIVER 1. Press the “CH” button to choose a signal channel you want to use. 2. Short press the power button to turn on the receiver, after hearing "beep" sound once, the receiver is under working status, then the green LED indicator will flash once in 5 seconds.
CHARGING AND CHECKING BATTERY LEVEL ★ Please charging before the first time using! Please use USB charger with the following parameters (this product can be charged with mobile phone charger or computer USB interface, please check the following parameters before charging): Input: 100-240V, 50/60HZ Output: 5V 1000 mA (or 300mA/500 mA) Charging the remote transmitter: Connect the USB cable, the battery icon on screen will keep flowing when charging, and stop when it is fully charged. Charging the receiver: 1.
FUNCTIONS TESTING Static shock function testing The static shock function can not be seen by our naked eyes, please check with our test lamp. Put the test lamp on the contact points, ensure the copper wire has touched both the contact points. Press the static shock function button, the lamp will glow. Vibration function testing Press the vibration function button, the receiver will vibrate. Warning tone function testing Press the warning tone function button, the receiver will produce “beep” sound.
HOW TO PUT ON THE RECEIVER COLLAR STRAP 1. Correct wearing position will make your dog training healthy and effective. The receiver has to be placed on the bottom of dog's neck and the screw caps should contact dog's skin directly. 2. If your dog neck is with long or thick hair, please use the longer screw caps. The soft silicone rubbers are also with conductive function, they can be put on to prevent iron rust 3.
HOW TO WEAR THE NYLON COLLAR STRAP ⑴ ⑵ ⑶ ⑷ If the collar strap is too long, trim the excess length appropriately. It is easy to get burrs after cutting, and you can use a lighter to burn the yarn to melt.
MAINTENANCE REGULARLY 1. Please check the tightness of the receiver and check whether there is with any damage outside. 2. Clean the screw cap with alcohol weekly. 3. Check the dog's neck and clean it weekly. USING PRECAUTIONS 1. The remote transmitter is with high-tech transmission, you don't need to aim at the receiver directly. The remote signal can penetrate obstacles like walls etc., but the effective distance will affect. 2.
Q: What is the function of the protection pads? A: 1. The protection pads can prevent the dog's skin from being worn, and avoid skin being hurt by the iron columns when our pets wear them for long time. 2. Anti-shock, to isolate static shock. .................................. Q: When will we use the protection pads? 1. When the dog training or anti barking has effects, let we use protection pads. 2.
Q：How long will it take to train my dog well? A：Correcting a bad habit or training it to obey your commands takes time, be patient with your dog. ..................................................... Q：The dog training collar doesn't work, or the dog doesn't respond after it is put on the dog's neck. How can I troubleshoot the problem? A： 1. Please check whether the devices are with battery. 2. Please check whether the function levels have been adjusted. 3. Please check whether the receiver is turned on. 4.
FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
