Quick Start Manual

Short press the power button
1.Screen On/Off 2.Return
Press and hold the power button
1.Power on 2.Power off
01 You can search and download “DaFit” App in many App markets such as APP
Store, Myapp, Google Play and so on.
02 Open the watch APP downloading interface, scan to download or scan the QR-code
to download.
Attach the magnetic charging base in the box to the back of the watch correctly and
plug the USB end into your computer, charging dock or power bank for charging.
Note: It is recommended to use the charger with the certification mark which is
commonly used in the market.
If you need to replace the watchband, please choose one with a width of 20mm.
1. To measure the values more accurately, wear the watch one finger away from the
carpal.
2. Please wear the watch close to your skin and make sure the watch will not move
during exercise.
1. Switch with the main interface
Press and hold the main interface, and slide left and right to select when the dial
plate is zoomed out; click the current interface, then the current dial plate will be
displayed.
2. Message
Slide to the right on the main interface to enter the message interface, and then
you can view the current messages. You can click the “Clear All” button at the
bottom to clear the current messages received.
Slide down the main interface to enter the control center, you can select the
shortcut interfaces, including: Brightness, Do Not Disturb, Weather Forecast,
Flashlight, Stopwatch, Settings, etc. Click one of the above shortcut interfaces to
quickly operate this interface.
4. Data Center
Slide to the left on the main interface to enter the Data Center, which includes
current step count data, last sleep data, last heart rate data, last blood pressure
data and weather. Slide to the data interface to view the current status data. To
measure the blood pressure, slide to the corresponding interface, and click "Click to
Measure".
5. Step Count
Slide up on the main interface to enter the main menu, and click on the number of
steps to view walking and calorie data, etc.
6. Sleeping Data
Slide into the main menu on the main interface and click Sleep Information to refer
to the last sleep data.
Note: The sleeping period is from 10 pm to 8 am next day.
7. Heart rate
Slide up on the main interface to enter the main menu, click on the Heart Rate to check
the data of last heart rate. Tap on "Click to Measure", and two "--" will be displayed on
the bracelet interface to indicate that the measurement is on the progress; when it is
completed, the bracelet will vibrate to give feedback, and the current test value of
heart rate will be shown in the heart rate interface.
8. Blood Pressure
Slide up on the main interface to enter the main menu, and click on Blood Pressure to
check the last blood pressure data. Tap on "Click to Measure", and "---/--” will be
displayed on the blood pressure interface to indicate that the measurement is on the
progress; when it is completed, the bracelet will vibrate to give feedback, and the
current measured blood pressure test value will be shown in the blood pressure
interface.
9. Blood Oxygen
Slide up on the main interface to enter the main menu, click on Blood Oxygen to check
the data of last blood oxygen. Tap on "Click to Measure", and "--" will be displayed on
the blood oxygen interface to indicate that the measurement is on the progress; the
measurement will last for about 35 seconds, then the bracelet will vibrate to give
feedback, and the current test value of blood oxygen will be shown in the bracelet
interface.
10. Sports
Slide up on the main interface to enter the main menu, and click Exercise to select
walking, running, cycling, rope skipping, badminton, basketball, football or swimming.
Select any sport to start recording the sport data.
11. Weather
Slide up on the main interface to enter the main menu, click on the Weather to view the
current weather status, the maximum temperature and the minimum temperature;
slide up to view the weather status, the maximum temperature and the minimum
temperature in the upcoming four days.
12. Camera Control
Slide up on the main interface to enter the main menu, click Camera Control, and then the
bracelet will access the camera of your mobile phone and enter the camera preview
interface; click the photo icon, and the mobile phone will automatically take photos after
counting down in 3 seconds.
13. Music Control
Slide up on the main interface to enter the main menu, and click Music Control. It includes
switching to the previous song/ pause or play/ switching to the next song. You can click
based on your own needs.
14. Stopwatch
Slide up on the main interface to enter the main menu, click Stopwatch and click Start
Timing, and press the Pause button to end it. To refresh the interface, click Refresh to
refresh the duration of the current record.
15. Brightness Adjustment
Slide up on the main interface to enter the main menu, click Other and click Brightness,
and drag up and down in the rectangle to adjust the brightness of the screen.
16. Vibration
Slide up on the main interface to enter the main menu, click Other and click Vibration to
turn on vibration, and click again to turn it off.
17. Do Not Disturb
Slide up on the main interface to enter the main menu, click Other and click Do Not Disturb
to block phone calls and message push. Tap again to turn off this mode.
18. Restore Factory Settings
Slide up on the main interface to enter the main menu, click Other and click Restore
Factory Settings, and the watch will show whether to restore factory settings. Click OK to
enter the factory reset, and click Cancel to exit the interface.
Remark: After restoring the factory settings, all data of the bracelet will be cleared.
19. About Device
Slide up on the main interface to enter the main menu, click Other and then click “about
Waterproof rating: IP68
If there are any problems in the use of watch, please try to troubleshoot
by referring to the following items.
This product is not permanently waterproof and may be weakened over time. It supports
short-time use such as hand washing and raining, but does not support using in hot
shower, scuba diving, diving, surfing and so on. The watch is not waterproof against the
erosive liquids such as seawater, acidic or alkaline solutions, chemical reagents, etc. In
case of accidental contact, please rinse with clean water and dry it. Any abuse or
incorrect use causing damage is not at the range of warranty.
Note: It is not recommended to wear the watch while taking a hot shower. Water vapor
will be produced when you are taking a hot shower. The small molecule is easy to seep
through the gap in the watch case. When the temperature goes down, it will gradually
condense into water droplets, thus damaging the circuit board and further damaging
the watch.
Note: Even a small amount of sweat or moisture can cause corrosion on the charging
end while the device is charging. This will result in data transmission being obstructed
and thus affect charging.
1. Avoid using sharp objects to clean the device.
2. Exposure to organic solvents, chemical cleaning products, or insect repellents may
damage plastic parts of the device.
3. After contacting with chlorine, salt water, suntan oil, cosmetics, alcohol or other
chemicals, please clean the device thoroughly with a cleaning rag, so as not to damage
it.
4. Avoid pressing keys in water.
5. Avoid fierce impact or violent use, so as not to reduce the service life of the product.
6. Avoid prolonged exposure to any extreme temperatures, so as to avoid permanent
damage.
7. Please wipe up the watch with a cleaning rag after a sweaty training session.
8. Make sure to wear the bracelet tightly when measuring the heart rate. The watch
calculates your heart rate by adopting the principle of light reflection. It collects the
signal reflected to the sensor after the light source propagates to the skin. If the bracelet
is not worn tightly, the ambient light will enter the sensor, which will affect the
measurement accuracy.
1. The watch cannot be started
A: The time for pressing the power-on key is too short. Please press it for more
than 3 seconds.
B: The battery is too low. Please connect it to a charger. (It is better to charge with
5V2A current, and it may take more than 30 minutes when charging via a
computer)
2. The watch will be turned off automatically
A: The battery is too low. Please connect the watch with a charger to charge.
3. The watch can only be used for a short time
A: The battery is not fully charged. Please make sure there is enough charging
time (minimum of 2 hours).
4. Data cannot be synchronized
A: The sports data cannot be stored in the background when you are not logged
in. Please register and log in.
B: The Bluetooth is not connected in both ways. Please refer to the connection
instruction.
C: The signal is unstable. Please disconnect Bluetooth and reconnect it, and try to
upload data again.
Description of Waterproofing
Cautions
Common Troubleshooting
Battery Charging
APP Downloading
Operating Instructions
The APP will prompt for a new firmware version, and users can choose to upgrade
firmware in the APP device interface.
Important Notice for Upgrade:
1. Upgrade can only be conducted when the battery power of watch is 50% or more.
2. During the upgrade process, the progress bar will be prompted. Please do not
operate anything on the bracelet until the mobile phone prompts the upgrade is
successful and the bracelet is automatically restarted.
Firmware Upgrade
Daily Wearing Method
Functions
After it is downloaded, please open the APP, and fill in your real personal information
(height, weight, and birth date). Click the watch icon in the middle, click the
equipment binding, and then click the equipment to complete the connection.
Note:
1. To successfully pair your watch and mobile phone, you need to turn on Bluetooth of
your mobile phone for connection to the device.
2. If you are using Android mobile APP, you must give location permission and enable
the mobile system location function, otherwise you may not be able to find the device.
3. When you connect to the APP for the first time, the date, time and language on your
phone will be synced to the watch. All data in the watch including steps, weather, etc.
will be zeroed out before connection.
Connection
1.Watch 3.Quick Start Manual2.Charging Cable
Packing List
Instruction Manual
Specification Parameters
Dimension of smart watch
46×31.5×9.65mm
Screen resolution
240×360 pixels
Screen size
1.57 inches
Product weight
43g
Battery capacity
Polymer lithium battery 200mAh
Operating temperature
0-40℃
Power
button
Display
screen