User's Manual
Thank you for purchasing the D6 Soundbar. Please read this user manual carefully and keep for future reference.
Warning
Caution:
To reduce the risk of electric shock, do not dismantle the product and do not expose the apparatus to rain or moisture.
No user-serviceable parts inside.
Refer servicing to qualified personnel only
The lightning flash within an equilateral triangle is intended to alert you to the presence of uninsulated
dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute an
electric shock to a person or persons.
Important! This symbol alerts you to read and observe important warnings and instructions on the unit
or in this manual.
Notice:
This appliance is not intended for use by persons (including children) with reduced physical sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
1. To prevent possible hearing damage, do not listen at high
volume levels for long time periods or a sudden high volume level.
2. Never use the device unsupervised! Switch off the device whenever you are not using it, even if not using it only for
a short while.
3. The appliance is not intended to be operated by means of an external timer or separate remote control system.
4. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard.
5. Before operating this system, check the voltage of this system to see if it is identical to the voltage of your local
power supply.
/SVUXZGTZ9GLKZ_/TYZX[IZOUT
6. The unit should not be impeded by covering the ventilation opening with items such as newspaper, table-cloths,
curtains etc. Make sure that there are at least 20 cm of space above and at least 5 cm of space on each side of the unit.
7. The apparatus must not be exposed to dripping or splashing and that objects filled with liquids,such as vases,
must not be placed on the apparatus.
8. To prevent fire or shock hazard, do not expose this equipment to direct heat, rain, moisture or dust.
9. Do not locate this unit near any water sources e.g. taps, bathtubs, washing machines or swimming pools.
Ensure that you place the unit on a dry, stable surface.
10. Do not place this unit close to a strong magnetic field.
11. Do not place the unit on a amplifier or receiver.
12. Do not place this unit in a damp area as the moisture will affect the life of electric components.
13. Do not attempt to clean
the unit with chemical solvents as this might damage the finish. Wipe with a clean, dry
or slightly damp cloth.
14. When removing the power plug from the wall outlet, always pull directly on the plug, never pull on the cord.
15. Depending on the electromagnetic waves used by a television broadcast, if a TV is turned on near this unit while it is
also on, lines might appear on the LED TV. Neither this unit nor the TV is malfunctioning. If you see such lines, keep this
unit well away from the TV set.
16. The mains plug is used to disconnect the device, the disconnected device should remain readily operable.
Important Safety Instructions
1. Read these instructions. Keep these instructions. Follow all instructions. Heed all warnings.
2. Do not use this apparatus near water.
3. Clean only with dry cloth.
4. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
5. Do not install near any heat sources such as radiators, heaters, stoves, or other apparatus (including amplifiers)
that produce heat.
6. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles or at the
point where they exit from the apparatus.
7. Only use attachments/accessories specified by the manufacturer.
8. Unplug this apparatus during lightning storms or when unused for long periods of time.
9. Refer all servicing to qualified service personal. Servicing is required when the apparatus has been damage in any way,
for example, when the power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
10. The AC plug is used to disconnect the device, the disconnected device should remain readily operable. In order to
disconnect the apparatus from the AC power completely, the AC plug must be removed from the AC outlet completely.
Preparation for Use
Unpacking and Set Up
•Remove the Sound bar from the carton and remove all packing material from the Sound bar. Save the packing material,
if possible, in case the Sound bar ever needs to be serviced or transported. The original carton and packing material is the
only safe way to pack your Sound bar to protect i from damage in transit.
•Remove any descriptive labels or stickers on the front or top of the cabinet. Do not remove any labels or stickers from the
back or bottom of the cabinet.
•Place your Sound bar on a level surface such as a table, desk or shelf, convenient to an AC outlet,out of direct sunlight,
and away from sources of excess heat, dirt, dust, moisture, humidity, or vibration.
•Unwind the Line cord connecting the AC adapter and extend it to its full length.
Protect Your Furniture
This model is equipped with non-skid rubber 'feet' to prevent the product from moving when you operate the controls.
These 'feet' are made from non-migrating rubber material specially formulated to avoid leaving any marks or stains on
your furniture. However certain types of oil based furniture polishes, wood preservatives, or cleaning sprays may cause
the rubber 'feet' to soften, and leave marks or a rubber residue on the furniture. To prevent any damage to your
furniture we strongly recommend that you purchase small self-adhesive felt pads, available at hardware stores and home
improvement center everywhere, and apply these pads to the bottom of the rubber 'feet' before you place the unit.
Power Source
This sound bar is designed to operate on normal AC Power source. For Europe, it works only under SMPS 110V-240V
～50hz/60Hz. Do not attempt to operate the Sound bar on any other power source. You could cause damage to the
Sound bar that is not covered by your warranty.
• This sound bar was especially developed for LED/LCD/Plasma TV's: It should not be used in combination with CRTTV's
(Cathode Ray Tube TV's) in order to avoid image interference.
• Safety and operating instruction manual should be retained for future reference.
• The apparatus should not be exposed to dripping, splashing or placed in a humid atmosphere such as a bathroom.
• Do not install the product in the following areas:
• Places exposed to direct sunlight or close to radiators.
• On top of other stereo equipment that radiate too much heat -Blocking ventilation or in a dusty area.
• Areas where there is constant vibration.
• Humid or moist places.
• Do not place near candles or other flames.
• Operate the product only as instructed in this manual.
• Before turning on the power for the first time, make sure the sound bar is plugged to power outlet.
• For safety reasons, do not remove any covers or attempt to gain access to the inside of the product. Refer any
servicing to qualified personnel.
• Do not attempt to remove any screws, or open the casing of the unit; there are no user serviceable parts inside.
Refer all servicing to qualified service personnel.
Overview of the Sound Bar main unit
Soundbar accessories
Place on a flat Surface
Place the sound bar horizontally on a flat surface such as a TV unit or shelves and align it centrally with the TV screen.
Allow some space between the speaker and the wall. Don’t place inside a cabinet or an a walled shelf. Follow this guidance
for best sound output and good airflow around the sound bar.
Remote Control
1: LED Display 2: AUX 3: OPTICAL 4: HDMI(ARC) 5:USB
6: DC IN 7: SW OUTPUT 8: Standby 9: VOL- 10: VOL+
D6
Sound bar
Specifications
Drivers
Audio Output Power
Frequency Response
Signal-to-Noise Ratio
lmpedance
Power lnput
bluetooth Version
Dimensions
Bluetooth Frequency
Technology
Model
5090*2 SB + 5.25inch SW
200W
55Hz-20KHz
66dB
ȍȍ
110V-240V~50Hz/60Hz
R.M.S 80W
Version: 5.0 Range:up to 10m
Soundbar: 62H*73D*750 Lmm
Subwoofer: H360*W135*D210 mm
2402MHz - 2480MHz
BT/AUX/HDMI(ARC)/OPTICAL/USB
D6
Soundbar assemble details
1: Please connect the left audio cable with the
right audio input.
3: Place the soundbar on a furniture. lt is ready to be used.
2: Hold the convex interface of the soundbar with one
hand and turn the other interface to the right
about 20 degrees until locks securely.
20°
Important Notes
SSZU8)'';>IGHRK
Adapter(1)
wall brackets (2)
TREB+
AUX
O
P
T
IC
AL
V
O
L+
VO
L
-
B
ASS
-
TR
EB
-
MUS
I
C
DIA
L
O
G
UE
MO
VI
E
P
A
IR
DIS
CO
NNECT
I
ND
I
C
A
TO
R
RESET
3D
B
A
S
S
+
HDM
I(ARC
)
B
LUE
T
OOT
H
M
UTE
×√
WARNING
:
If you don’t feel confident to correctly and securely wall-mount the sound bar, Seek the assistance of an
experienced person of professional.Install the speaker on a vertical, fast, reinforced area of wall. For plaster walls, it is
recommended to screw into wall studs for greater security. For optimum performance, allow at least 25mm/1’’distance
between the sound bar and the TV.
25mm / 1”
25mm / 1”
Mount on the wall
Follow below steps to mount the sound bar on the wall
1: Paste 2 pieces of EVA foam (with holes) on the two wall brackets aligning at the hole position of wall brackets.
2: Remove 4 screws from the rear housing of sound bar, then insert the 4 screws over the wall bracket screw holes aligning
(on the side of EVA foam pasted), and then fasten the screws again.
3: According to the two hanging wall positions on the rear of soundbar, calibrate and mark the two hanging brackets hole
position on the wall. Then drill two holes on the wall, firstly insert two expansion plastic screws on the wall, then fasten the
hanging screws into expansion screw holes.
backing paper
EVA foam
(with holes)
EVA foam
w
ithout
h
oles
560±5mm
4: Then Paste the 2 pieces of EVA foam (without holes) on the two wall brackets downward. Then place the hollow cross in
the center of the bracket against the screws on the wall and hang the sound bar on the wall finally.
Manufactured under license from Dolby Laboratories. Dolby,
Dolby Audio,and the double-D symbol are trademarks of
Dolby Laboratories.