User's Manual

ManualsBrandsShenzhen Acartool Auto Electronics ManualsAutomotiveCar diagnostic tool

Oil Light Reset

This function allows you to perform reset for the Engine Oil Life

system, which calculations

An optional oil life change interval depending on the vehicle

driving conditions and climates. The Oil Life Reminder must be

reset every time the oil is changed, so the system can calculate

when the next oil change is required.

EPB Reset

This function has a multitude of usages to maintain the elec-

tronic braking system safely and effectively. The applications

include deactivating and activating the brake control system,

assisting with brake fluid control, opening and closing brake

pads, and setting brakes after disc or pad replacement, etc

ABS Bleeding

This function allows you to perform various bi-directional tests

to check the operating conditions of Anti-lock Braking System

(ABS). 1. When the ABS contains air, the ABS bleeding function

must be performed to bleed the brake system to restore ABS

brake sensitivity. 2. If the ABS computer, ABS pump, brake

master cylinder, brake cylinder, brake line, or brake fluid is

replaced, the ABS bleeding function must be performed to

bleed the ABS.

Throttle Relearn

This function enables you to make initial settings to throttle

actuators and returns the “learned” values stored on ECU to the

default state. Doing so can accurately control the actions of

regulating throttle (or idle engine) to adjust the amount of air

intake.

SAS Reset

To reset the steering angle, first find the relative zero point

position for the car to drive in straight line. Taking this position

as reference, the ECU can calculate the accurate angle for left

and right steering. After replacing the steering angle position

sensor, replacing steering mechanical parts (such as steering

gearbox, steering column, end tie rod, steering knuckle),

performing four-wheel alignment, or recovering car body, you

must reset the steering angle.

Definition of Special Function

Diagnose - Clear fault code

Do you want to erase all the fault

code (s)?

Information

Yes No

After reading the retrieved codes and making appropriate

vehicle repairs, use this function to clear fault code.

Special Function

Diagnose - DataStream

CHRYSLER

Current Fuel Shutoff

SKIM VTA Invalid Key

Received Fault Posted

NGC Should Shut Off Fuel

ASD

False

Fuel On

SKIM/VATA Has Completed False

IGN RUN START SW On

When this function is selected, the screen displays the data list for

the selected module. The items available for any control module

vary by vehicle. The parameters display in the order that they are

transmitted by the ECM, so expect variation between vehicles.

OBDII Function

This section describes the various functions of each option:

1. Stored codes are the current emission-related DTCs from the

ECM of the vehicle. OBD II/EOBD Codes have a priority according

to their emission severity, with higher priority codes overwriting

lower priority codes.

2.This option is used to clear all emission-related diagnostic data

such as, DTCs, Freeze frame data and manufacturer-specific

enhanced data from the vehicle’s ECM, and reset the I/M Readi-

ness Monitor Status for all vehicle’s ECM.

3.This function displays the real time PID data from ECU. Dis-

played data includes analog inputs and outputs, digital inputs

and outputs, and system status information broadcast on the

vehicle data stream.

4. These are codes that were generated during the last drive

cycle, but before the DTC actually sets, two or more consecutive

drive cycles are needed. The service is to assist the service

technician after a vehicle repair and after clearing diagnostic

information, by expect or see differences between makes.

5. Typically, the stored frame is the last DTC that occurred. Certain

DTCs that have a greater impact on vehicle emission, have a

higher priority. The top prioritized DTC is the one for which the

freeze frame records are retained.

6. This function is used to check the readiness of the monitoring

system. It is an excellent function to use prior to having a vehicle

inspected for state emissions compliance. Select I/M readiness to

display a sub menu with two choice.

7. Use this option to view the result of On-Board Monitor tests.

The tests are useful after servicing or after erasing a vehicle’s

control module memory.

8. The option displays the vehicle identification number (VIN), the

Please Select the Nameplate:

[1] Read Current Trouble Code

[2] Clear Trouble Code

[3] Read Current Data

[4] Read Pending Trouble Code

[5] Read Freeze Frame Data

[6] Readiness Tests

[7] On-Board Monitoring Test

[8] Read System Information

Setting

Record

Language

Unit

Beep

Display record setting menu.

Record includes: On and Off.

Press OK to change the record setting selection.

This function allows data recording during the

Display multi-languages function menu.

Total 18 languages optional. Only 2 languages

loaded before delivery: English + local language

Display unit setting menu.

Unit includes: Metric and English units.

Press OK to change the unit setting selection.

Display beep setting menu.

Beep includes: On and Off.

Press OK to change the beep setting selection.

Button Test

LCD Test

Display button function menu.

Press the FN key for 2 seconds to quit the

button test.

Display LCD test function menu.

Press ESC to quit the LCD test.

Record

Language Unit Beep

Button Test LCD Test

Why cannot install VDiagtool Update client correctly?

After installing the VDiagtool Update Client software, the

system won’t accept the serial number for the auto scanner.

Note: You need to connect auto scanner to PC with the USB

cable before software download.

Why the vehicle linking error ?

A communication error occurs if the auto scanner fails to

communicate with

the vehicle ECU. Follow the steps to check the connections:

1– Verify the ignition is ON.

2– Check the cable or connector is securely connected t the

vehicle DLC.

3– Turn the ignition off and wait for about 10 seconds and

turn the ignition back to ON and continue the testing.

4– Verify the control module is not defective.

Why the device doesn’t power up ?

If the auto scanner won’t power up or operate correctly in

any other way, follow the steps to check the connections:

1– Check the connector properly inserted to the socket seat.

2– Check the DLC pins bent or broken.

3– Clean the DLC pins if necessary.

Why the device have no permission to update?

Please contact the local distributor to get authorization.

Why cannot find the WIFI name ?

The device can only display the Wifi name consisting of

English character or numbers.

12-Month Limited Warranty

VDiagTool warrants to the original retail purchaser of this

VT100 auto scanner, that should this product or any part

thereof during normal consumer usage and conditions, be

proven defective in material or workmanship that results in

product failure within twelve (12) months period from the

date of delivery, such defects will be repaired, or replaced

(with new or rebuilt parts) with Proof of Purchase, at the

Company’s option, without charge for parts or labor directly

related to the defects.

The Company shall not be liable for any incidental or

consequential damages arising from the use, misuse, or

mounting of the auto scanner. Some states do not allow

limitation on how long an implied warranty lasts, so the above

limitations may not apply to you.

This warranty does not apply to:

A) Product subject to abnormal use or conditions,

accident, mishandling, neglect, unauthorized

alternation, misuse, improper installation or repair or

improper storage;

B) Products whose mechanical serial number or

electronic serial number has been removed, altered

or defected;

C) Damage from expose to excessive temperatures or

extreme environmental conditions;

D) Damage resulting from connection to, or use of any

accessory or other product not approved or author-

ized by the Company;

E) Defects in appearance, cosmetic, decorative or

structural items such as framing and non operative

parts;

F) Product damaged from external causes such as fire,

dirt, sand, battery leakage, blown fuse, theft or

improper usage of any electrical source.

IMPORTANT: All contents of the product may be deleted

during the process of repair. You should create a back-up

copy of any contents of your product before delivering the

product for warranty service.

FAQ

Warranty

About

Product Serial Number: VT1000002

Firmware Version: 7001.7048

System Software Version: 5.72

www.vdiagtool.com

(NOT SUPPORT USB MODE)

About Display the system information including the register

password, firmware version, system software version

and company information

Searching Wifi ...

UPDATE

Update Instructions and Procedures

Connecting Wifi ...

UPDATE

Connecting Server...

UPDATE

HOTSPOT

PRD

Internet Telcel

HH41NH_BE7B

PRD_Wi-Fi5

e4:e1:30:82:8e:7b

c0:b4:7d:f3:ae:99

Bosscomm 5G f4:2a:7d:50:a6:88

FEIKEYY 64:6e:97:a4:71:b8

[1]

[2]

[3]

[4]

[5]

c0:b4:7d:63:ae:94 88

PASSWORD

1a2345

0 1 2 3 4 5 6 7 8 9 .

q w e r t y u i o p ,

a s d f g h j k l ) -

z x c v b n m / * ( _

ABC SPACE Backspace

UPDATE

AMFORD, EUR

FORD

BMW

5.82

3.7

CHANA 3.14

37.81MB

7.01MB

4.29MB

[1]

[2]

[3]

[4]

4.22 19.54MB

BENZ

√

Reset Submit

Fax

Phone

Name

Position

Contact

Address

Website

Registration

Update

Via USB

Via WIFI

Update via WIFI mode

Update via USB mode

Step 1 Searching WIFI signal after selecting the WIFI icon. Step 2 The system will list all HOTSPOT on site. Step 3 Input the password if necessary. Step 4 Connecting the WIFI during the testing. Step 5 Connect the Server as above. Step 6 Select the car makes for update according to the

demands.

Step 5 Input the necessary information during the first

registration.

Step 6 Select the car makes for update according to the

demands.

EPB

These functions perform various component adaptations, allowing

you to recalibrate or configure certain components after some

maintenance or replacement.

ABS BLEED OIL RESET SAS

THROTTLE

Step 3 Visit the website www.vdiagtool.com

Step 4 Download VDiag Update Client to PC according to

the instructions.

1. Make sure the update client has been installed in

your PC (Windows 7/8/10 only).

2. Make sure the device and your PC connect with USB

cable.

3. Press “OK”, the device will restart and enter the

update mode.

4. Run the update client in your PC,

INFORMATION

Step 1 The information mentioned above will be displayed

during the update.

Step 2 Connect the PC to VT100 main unit with USB cable.