9" LCD MONITOR REV A User Manual 19" LCD Monitor HL1916AMT-R/L
19" LCD MONITOR REV A Contents Contents ................................................................................................................................................................................ I 1. Application........................................................................................................................................................................1 2. Declarations ............................................................................................
19" LCD MONITOR REV A 9.1 Front 、Platform and Side view ..........................................................................................................................30 10 Remarks and contact address .........................................................................................................................................
19" LCD MONITOR REV A Federal Communications Commission(FCC) Statement You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the use’s authority to operate the equipment FCC-Class B This equipment has been tested and found to comply with the limits for a Class B digital device, Pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a communications.
19" LCD MONITOR REV A 2. Declarations Safety precautions Medical Equipment With respect to electric shock, Fire and mechanical hazards only in accordance with IEC/EN60601-1 and CAN/CSA C22.2 No. 601.1 Regular maintenance and calibration are recommended Please note that liquid crystal displays such as the HL1916AMT do not have a failure rate of zero and image parameters may change over time (e.g. luminance or discoloration).
19" LCD MONITOR REV A Explanation of the symbols Attention: Consult the accompanying documents Alternation current (AC) Protective earth CAUTION:Risk of electric shock. Do not open.
19" LCD MONITOR REV A Danger: There is a danger to life if the warning information is not observed. Severe personal injury or damage to property may occur. Do not open the unit yourself. Certain components inside the units are at high-voltage, i.e. touching these components presents a danger to life! Only use a perfect power supply cable A damaged power supply cable may result in a fire or electric shock. When disconnecting the power supply cable, always do so by holding the plug.
19" LCD MONITOR REV A for the installation. Use power cables with a PE contact. Only insert into sockets with a PE contact. For certain applications, the video earth can be separately connected to the PE via the additional PE connection in the plug panel (observe IEC 601-1-1). Close the plug panel using the provided cover (meaning the display stand), and secure using the screws. Turn switch off and then remove power cord.
19" LCD MONITOR REV A Mounting screws Number 4 Thread M4 Strength 12 Immersion depth Min. 10 mm; Max. 12 mm Torque Max. 3 Nm The permissible ambient temperature range (5 °C ... 40 °C) must not be violated. Do not subject device to unnecessary shocks. Take care when transporting! Use the original packaging! The panel in particular should be protected against shocks.
19" LCD MONITOR REV A Lamp Disposal Hg Lamp(s) inside this product contains mercury and must be recycled or disposed of according to state, local or federal law. For more information, Contact the electronic industries alliance at www.Elae.org. For lamp specific disposal information check www.lamprecycle.org.
19" LCD MONITOR REV A 3. Installation Provide adequate ventilation Ventilation slots are located on the rear of the housing. Ambient temperature The permissible ambient temperature range must not be violated. Minimize reflections The display should be positioned so that reflections of lights, windows, furniture with shiny surfaces or light-monochrome walls do not appear on the screen.
19" LCD MONITOR REV A 4. Start-up Caution In order to ensure safe operation of the equipment, close attention must be paid to the information contained in this Instruction Manual as well as the warnings in Section 2 "Safety precautions". Caution Information for end customer None of the settings must be changed on site by the user, otherwise the guarantee is canceled. This also applies to settings made using the HL1916 keys. These are therefore locked for certain applications.
19" LCD MONITOR REV A 4.1.1 Little cover (removing) Remove the one screws with an M4 Slot screwdriver (one turn suffices). Open the little cover and remove it 4.1.2 Cable (attaching) Connect the cables to the display.
19" LCD MONITOR REV A 15-pin Sub-D connector: the flat panel display can be connected to the computer system using the Sub-D connector. The display is adapted using an OSD menu. DVI connection: The connection to the computer can also be made via the digital single link or via the analog channel of the DVI connection. The picture quality, noise immunity and radiated interference of the complete system depend on the cable quality and length.
19" LCD MONITOR REV A 4.1.3 Little cover (attaching) Lead the monitor end of the cables through the little cover’s cable duct. Connect the little cover to the rear cover. 4.2 Power up the display Power up the display. The operation LED lights up. 4.3 Adjusting the image geometry The display automatically recognizes the used standard, and set-up values for each standard are preprogrammed.
19" LCD MONITOR REV A still visibly contrast from one another. To adapt the luminosity to the ambient lighting, adjust the backlight brightness (note: 500 cd/m² factory setting is then modified). 4.5 Screen saver A screen saver function should be used in order to reduce "image sticking" which can occur in TFT displays. It is high risk to display a static graphic over half an hour.
19" LCD MONITOR REV A 5. Connections 5.1 Connecting the flat panel display Note All screening precautions contained in the corresponding EMC guidelines must be observed. If these guidelines are not observed, interference signals could penetrate the monitor. Information on cable installation Only screened cables are permitted for the signal connections. All connectors should be of screw or locking types (as far as possible). Signal and power cables must not be routed in the same duct.
19" LCD MONITOR REV A 5.3 Information on additional serial interface (Service Only) Serial connection: you can connect the display via the 9pin D-SUB connector to the computer for firmware updating and monitor test. 5.4 Analog and digital inputs (DVI-D, VGA) 15-pin Sub-D connector Connect VGA cable with 15-pin Sub-D connector (male) for the analog input to the 15-pin Sub-D connector (female). DVI socket With DVI digital signal. 5.
" LCD MONITOR REV A 6. Adjustments 6.1 Picture adjustment This section describes the settings for operation of the flat panel display with a video source. The most important settings are: Adjusting the graphics memory of the video source As with all monitors, the flat panel display also has certain limits, e.g. maximum resolution and vertical frequency. The graphics adapter must be set when using the flat panel display such that the limits are observed.
19" LCD MONITOR REV A slightly until the display is just above the absolute lowest black level (one step is generally sufficient). Similarly, set the white level using a 100%-white test pattern and the measurement device. Only the contrast level should be adjusted to ensure that the black level remains unchanged. • Control again the black value did not change. In case it did you need to duplicate the two previous steps until it does not change anymore (cause: pedestal).
19" LCD MONITOR REV A 6.3 OSD menu 6.3.1 Keys assignment and operation LED A “dynamic help for keypad function” is available for each menu: it explains the role of each key depending on the OSD menu window, which is currently active. 6.3.2 Key functions without active OSD menu Key Action Menu Activate OSD Up Adjust Backlight Down Analog Input auto balance * Scenario in case all signal sources is available. If not, the signal from the next available source will be displayed. 6.3.
19" LCD MONITOR REV A Down Exit Selection point Command Slide controller Selection point Except "Exit OSD" menu In "Exit OSD" menu To previous selection "Enter key" Decrease value To subsequent selection One menu level upwards (settings are retained) Return to main menu (settings are retained) 6.3.4 Submenu calls Press the “Menu” key while the OSD is active, the function icon will jump to next line. Pressing the “Up” key, the coordinate submenu will be selected. 6.3.
19" LCD MONITOR REV A 6.4 Description of the menus Main Menu Function Adjustment range 0…255 Adjustment of contrast This allows the brighter area to be seen more distinctly. The center point is in 128 position. Note: for DVI-D signals the Contrast setting is optimized. Manual changes are not recommended. Brightness 0…255 It is used to adjust the Brightness of the monitor. The center point is in 255 position. This allows the darker area to be seen more distinctly.
19" LCD MONITOR REV A Auto function (Analog input only) AutoBalance Auto -Config On/Off On/Off Automatically adjusts the image position, H-Size (or V-Size) The selected auto functions are executed. Note: The quality of the function depends on the applied picture contents. To get better effect it is recommended to apply full screen and including whiteness contents picture. Execute Auto adjust on mode change The auto functions are used to assist the automatic setting of parameters.
19" LCD MONITOR REV A OSD Lock Timer DPMS off The backlight will not switch off if it is no input signal. Only switches off along with the power switches off. 120sec If there is no action in 2 minutes, the OSD will be locked automatically. The OSD’s content will be saved.
19" LCD MONITOR REV A No picture appears on Broken fuse the display, operation LED off Power cable not inserted or incorrectly inserted No picture appears on No video signal the display, operation Video source not LED green blinking supplying a signal Fuzzy picture, Scanning frequency or interference in phase incorrectly set vertical lines Other faults –LED Loose plugs orange blinking Faulty cable Inform servicing department Insert power cable Check video cable Check video source Adjust frequency and phas
19" LCD MONITOR REV A 8. Technical data All technical data are valid after a warming-up period of 2 hours. 8.1 Display Type Display area Picture diagonal Native resolution Pixel organization Pixel pitch Contrast ratio Horizontal viewing angle Vertical viewing angle Backlight Brightness Lifetime backlight TFT,color active matrix 376.32 mm x 301.056 mm 19" or 48 cm 1280 x 1024 (full-screen format) 3 vertical sub pixels 0.294 mm x 0.
19" LCD MONITOR REV A 8.3 Electronics Multi-standard technology Timing recognition Video modes with resolutions less than 1280 x 1024 can be expanded to the TFT resolution, and thus utilize the full display area (like multi-sync CRTs). In the same way, resolutions higher than 1280 x 1024 can be reduced and then displayed.
19" LCD MONITOR REV A 8.4.3 Serial interface RS232 Via D-sub 9pin 8.4.4 Timing Input Input Signals Analog Digital Horizontal frequency 31kHz -82kHz 31kHz -82kHz Vertical frequency 50.0Hz - 85.0 Hz (Non-Interlaced) 50.0Hz - 85.0 Hz (Non-Interlaced) Video Signal Analog RGB Digital RGB Sync. Signal Separate Sync. (TTL) Composite Sync. Sync on green TMDS Pixel Clock 25.0MHz -140.0MHz 25.0MHz -140.0MHz Input connector Mini D-sub 15Pin DVI-D 8.
19" LCD MONITOR REV A 8.6 Mechanical design Housing components Aluminum Protective screen No Visible screen surface Approx. 376 mm x 301 mm Ventilation slots In rear panel Degree of protection (front) IP20 to DIN 40 050 Connection panel At rear, covered Weight: Without stand With stand 6.5 kg (approximate) 7.9 kg (approximate) Dimensions (W x H x D) in mm 425 ×350×78.5mm 8.
19" LCD MONITOR REV A 8.8 Mechanical requirements Operation Vibration Shock According to EN 60068-2-6 10 ... 58 Hz with ± 0.075 mm deflection 58 ... 500 Hz at 10 m/s² According to EN 60068-2-27 (single shock) 150 m/s², 6 ms No permanent shock allowed in operating conditions Packed unit Vibration According to EN 60068-2-6 5 ... 9 Hz with ± 3.5 mm deflection 9 ...
19" LCD MONITOR REV A 8.
19" LCD MONITOR REV A 9. Dimensional drawings All dimensions in mm. 9.
19INCH LCD MONITOR REV A 10 Remarks and contact address Invalidity of guarantee All unauthorized electrical or mechanical alterations on or in the unit result in loss of the guarantee. Information on the Instruction Manual For clarity reasons, this Instruction Manual does not contain all detailed information on this product.
