Customer Specification 15.3 Inch Color LCD Display Model: Name HL1530 Department/Title Date Signature Change History Version Date Author Modification A0 2013-5-29 Zhai Tao Preliminary Jin Zhonghua Zou Yanyan A1 2013-12-10 Zhai Tao Update the Label information Jin Zhonghua Add mechanical color details Zou Yanyan Update the new 2D drawing illustrate the part of sheet metal. Add 3.1 section, Note1 and Note2 Add 2.
CONTENTS 1. SCOPE.................................................................................................................................................. 4 Abbreviations............................................................................................................................................ 5 2. ELECTRICAL PERFORMANCE ...................................................................................................... 6 2.1 Power Supply ..........................................
4.3 Mechanical Load.........................................................................................................................................18 4.4 Packed unit ..................................................................................................................................................19 5. REGULATION................................................................................................................................... 19 5.1 Safety Specifications .............
1. SCOPE This document defines the performance requirements for a 15.3-inch TFT LCD color monitor with touch screen for medical use. This product is controlled by model name; any change will be recorded in the list and confirmed by customer. This high-resolution color display is specifically designed to meet the rigorous performance standards needed for surgery. To guarantee image integrity, features include accurate signal conversion.
Abbreviations The following abbreviations are used in this document: Acronym Definition ABS CR DC DDC EDID FPC GND HDMI I2C LCD LED MTBF PC PCAP P/N RoHS USB Acrylonitrile Butadiene Styrene Contrast Ratio Direct Current Display Data Channel Extended Display Identification Data Flexible Printed Circuit Ground High Definition Multimedia Interface IC to IC Communication Liquid Crystal Display Light Emitting Diode Mean Time Between Failures Polycarbonate Projective Capacitive Part Number Restriction of Hazar
2. ELECTRICAL PERFORMANCE 2.1 Power Supply Table 2.1 : DC12V ± 10% -Input Voltage - Current (max) : 3.0 A - Power Consumption : <40W 2.2 Power Management The following table shows the power consumption feature: Table 2.
2. Print the following information in specific regions on the surface of metal plate: X1, X2, X3, X4, X100. 3. Conn.PE(X100) is M4*14mm stud with 2 flat washers and nut. Use to secure protective earth connection from the Host cable. The corresponding relations as follows: Connector USB out USB in HDMI Power Ground(PE) Label X4 X3 X2 X1 X100 2.3.1 Signal Specifications Table 2.
Figure 2.2 HDMI connector 2.3.3 USB 2.0 Interface The monitor supports touch function, the touch screen can be used in the Microsoft® Windows 7. Figure 2.3 USB-A connector Figure 2.4 USB-B connector Table 2.5 Pin Signal 1 VBUS 2 D- 3 D+ 4 GND USB A-Type Used for external USB function, such as a USB mouse, flash disk. USB B-Type USB is connection to host system, in order to enable Touch panel. 2.3.4 Power connector The power connector use TE AMP 1-350942-0. Figure 2.
2.3.5 Serial Port Serial Port Figure 2.5 Serial Port Serial port for factory firmware upgrade(Port located under the VESA plate mounting). 2.4 Panel Features Table 2.6 Panel Module NL12876BC26-32D Panel Type a-Si TFT-LCD Size 15.3” (39 cm diagonal) Aspect Ratio 15:9 (W:H) Active Display Area 334.08 (H) x 200.45 (V) mm Resolution 1280 (H)x 768 (V) pixels Pixel Pitch 0.261(H) x 0.261(V) mm Color Depth 16.7M Lamp Type LED (Replaceable module) Surface Anti-glare polarizer 2.
2.5.2 Brightness The light output shall be set on 370Cd/m2 output during manufacturing. When this light output cannot be reached, but the panel is within specification, the light output should be set to maximum output. 2.5.3 View angle Left/Right: 88/88 degree (Typ.); 80/80 degree (Min.) (CR≥10) Up/Down: 88/88 degree (Typ.)/; 80/80 degree (Min.) (CR≥10) (Note 2) (Note 2) 2.5.4 Luminance Uniformity LU less than 1.3 (Note 5) 2.5.5 Contrast ratio 700:1 500:1 (Typ.) (Note 3) (Min.) 2.5.
2.6.2 General Specification Table 2.9 Item Specification Frame Size 385.08mm X251.45 mm Tolerance -0.2,+0.2mm Active Area 334.08 X200.45mm Black Silkscreen 25mm perimeter outside viewable area Surface Treatment Chemically hardened glass, no anti-reflective treatment Total Thickness 3.20±0.50 mm Attachment Optically bonded to TFT LCD Module Notes: The touch screen controller support grip suppression and palm rejection algorithms. 2.6.3 Environmental Characteristics Table 2.
Remark: 1. Parameters The relevant touch panel parameters are developed between Philips and Ocular. The parameter settings are pre-loaded by standard firmware loading of the touch panel controller at Ocular factory. The parameter file shall be under configuration control. 2. Firmware Version Firmware is released by Ocular to maintain manufacturing configuration control. Version: F153-1664S-001 V2.0.xcfg 3. Calibration The P-Cap sensor is matrix based. No calibration is required.
Ratio of gray max (Gmax) & gray min (Gmin) at the center point of the panel. Gmax: Luminance with all pixels white Gmin: Luminance with all pixels black Note 4: Definition of Luminance of White: Luminance of white at center point. Note 5: Definition of luminance uniformity The luminance uniformity is calculated by using following formula.
3. MECHANICAL SPECIFICATIONS 3.1 Outline Dimensions & Weight Figure 3.1 Table 3.1 Item Set Width 390.08mm Depth 256.45mm Color of main enclosure and rear cover Pantone Cool Grey 1M Color of bezel Pantone Black 2M Housing components Plastic(ABS+PC) Visible screen surface Approx. 334.08 (H) x 200.45 (V) mm Degree of protection IP21 Connection panel At rear VESA 75 x 75 mm Net weight 4Kg Note 1: The monitor shall not require specialized mechanical installation tools.
3.2 Mechanical Color The monitor has two colors for the bezel/housing design: - Philips: Mushroom (40383); Pantone: Cool Gray 1M - Philips: Ultra Dark Gray (10714); Pantone: Black 2M 3.3 Packaging Figure 3.2(Carton) Table 3.2 Carton Box Dimension Width (mm) 447 Depth (mm) 180 Height (mm) 395 Gross weight 5Kg Foam inserts illustration: Figure 3.3 Front illustration(30°) Last change: 2013-12-10 Copyright @ Shenyang Torch-Bigtide Digital Tech.,Co.,Ltd Figure 3.
3.4 Texture Texture of plastic parts shall be: VDI 3400 REF 30 (Supplier reference VDI3400 REF 22G allowed as equivalent). Manufacture Serial Number 3.5 Label 3.5.1 Production Label Figure 3.5 Philips 12NC number 3.5.2 The color of Product Label The colors of the product label shall match: Background: Matte silver Text: Black. 3.5.3 Packaging Label Figure 3.6 Last change: 2013-12-10 Copyright @ Shenyang Torch-Bigtide Digital Tech.,Co.
3.5.4 Manufacture Serial Number The manufacture serial number consists of 14 characters (majuscule and numbers), format as below: 10287 13 3 1 10 001 Serial number Top Version PN （Pilot Number） Month （1,2,3,4,5,6,7,8,9,A,B,C） Year The last figure of production number. Notes: Month using hexadecimal, A, B, C substitute for October, November, December. Example: HL1530 products machine Part Number 301010287, TOP version 1.
4. ENVIRONMENT CONDITONS 4.1 Operation Environment（Philips XN-039059） Table 4.1 Ambient temperature range +10 -- +40°C Ambient humidity 20%-80% Temperature gradient < 0.5°C/min Atmospheric pressure range 70 – 110 kPa 4.2 Transport and Storage (Packed) （Philips XN-039059） Table 4.2 Ambient temperature range -25 -- +70°C Ambient humidity 5%-95% Temperature gradient Max. 10°C/h, no condensation Atmospheric pressure range 70 – 110 kPa 4.3 Mechanical Load Operation （Philips XN-039137） Table 4.
4.4 Packed unit According to 2M2 EN60721-3-2 5. REGULATION 5.1 Safety Specifications Table 5.1 Safety standards IEC60950-1、FCC Part 15 Class B、 CISPR 11 Group 1 Class B Approvals FCC、CB (NCB Lab.) Protection class Degree of protection to IEC 60529 Conformity class III IP21 CE 5.2 Electromagnetic Compatibility The unit shall comply with CISPR 11 Group 1 Class B - 3dB for conducted and radiated emission.
7.2 Dot Defect Table 7.
7.2.1 Close defect dots 7.2.2 Linked defect dots Last change: 2013-12-10 Copyright @ Shenyang Torch-Bigtide Digital Tech.,Co.
Last change: 2013-12-10 Copyright @ Shenyang Torch-Bigtide Digital Tech.,Co.
7.2.3 Appearance specification Table 7.3 Condition d<0.2mm 0.2mm ≤d<0.3mm 0.3mm ≤d≤0.5mm d>0.5mm W<0.05mm L<0.7mm 0.05mm ≤W≤0.1mm 0.7mm ≤L≤1.0mm L>1.0mm W>0.1mm d<0.2mm 0.2mm ≤d≤0.5mm d>0.5mm Defect pattern Dot shape Impure ingredient Stains Dust Line shape Bubbles, Wrinkles, Dent Criteria Allowed ≤10 points ≤3 points 0 point Allowed ≤4 points 0 point Allowed ≤2 points 0 point S≤0.2mm2 Allowed S>0.2mm2 0 point Scratch(Surface of polarizer) Note1: Definition of symbols is as follows.
8. Cosmetic Specifications and Acceptance Criteria Summary (Touch Panel) Spots, Dots or Bubbles, (circular blemishes and defects) – TP viewable area >10" Diameter (mm) Accept Quantity Diameter ≤ 0.35 mm 0.35 mm < Diameter ≤ 0.50 mm 0.50 mm < Diameter ≤ 0.80 mm Diameter > 0.8 mm Disregard or ignore Quantity ≤ 5 Quantity ≤ 2 Quantity = 0 Minimum Distance Between blemishes / 5mm 20mm / Lines, Linear Fibers or Scratches in viewable area Width (mm) W ≤ 0.04 0.04 < W ≤ 0.08 mm 0.08 < W ≤ 0.10 mm W > 0.
Last change: 2013-12-10 Copyright @ Shenyang Torch-Bigtide Digital Tech.,Co.
