Customer Specification HL1936SMT-L/R 19 Inch LCD Display Name Last change: 2015-1-23 Department/Title Copyright @Bigtide All rights reserved Date Signature HL1936(HL1936SMT-L Page 1 of 37 /R internal) For GE
Change History Update date Author Page 2015/1/23 JinZhonghua Last change: 2015-1-23 Copyright @Bigtide All rights reserved Content A0 HL1936(HL1936SMT-L Page 2 of 37 /R internal) For GE
CONTENTS 1. 2. SCOPE .................................................................................................5 ELECTRICAL PERFORMANCE......................................................6 2.1 Power Supply.......................................................................................................6 2.2 Power Management .............................................................................................6 2.3 Signal Interface ......................................................
5.7 MTBF ................................................................................................................26 6. 7. DEFECT, SCRATCH and DUST......................................................26 NOTICE FOR HANDING ................................................................32 Handing....................................................................................................................32 Appendix 1 Preset Timings ............................................................
1. SCOPE This document defines the performance requirements for a 19.0-inch TFT LCD monochrome monitor for medical use. This product is controlled by model name; any change will be recorded in the list and confirmed by GE. This high-resolution monochrome display is specifically designed to meet the rigorous performance standards needed for diagnostic, interventional radiology, and other medical applications.
2. ELECTRICAL PERFORMANCE 2.1 Power Supply -Input Voltage : DC24V 10% - Current (max) : 2A - Power Consumption : <50W 2.
Item SPEC Analog: Frequency H 30 ~ 82kHz V 50 ~ 85Hz Analog Signal Pixel clock 25--165MHz Input Video Input Analog 0.7Vpp VGA Input Impedance 75 Ohm Sync Signal Separate Sync, TTL (N or P),SOG Video Level: 0.5---1.0V CVS Signal Input Digital Signal Input Sync level: 0.2---0.3V DVI-Digital DVI Digital Input DDC via DVI 2.3.
Only support DVI single link ，pin 4,5,12,13,20,21 do not work.
Figure 4 USB-B connector Pin Signal 1 VBUS 2 D- 3 D+ 4 GND 2.4 Product Features Specification Item Analog Input LCD Digital Input Panel Module INNOLUX R190EFE-L53 Size 19.0” (48 cm diagonal) Active Display Area 376.32 (H) x 301.056 (V) mm Resolution 1280 x 1024 dots (SXGA) Pixel Pitch 0.294(H) x 0.294(V) mm Luminance 1400cd/m2 (typical); 1200cd/m2 (min.) Viewing Angle (Type.
Input Signals Horizontal frequency 31Hz –82kHz 31kHz -82kHz Vertical frequency 50.0Hz - 85Hz (Non-Interlaced) 50.0Hz -85 Hz (Non-Interlaced) Video Signal Analog RGB Digital RGB Sync. Signal Separate Sync. (TTL) Composite Sync. Sync on green TMDS Pixel Clock 25.0MHz -165.0MHz 25.0MHz -165.0MHz Input connector Mini D-sub 15Pin DVI-D Control key Menu, up, down, exit Functions OSD Backlight, Contrast, Brightness level, Position, Size, Phase, Gamma, DICOM etc.
2.5 Screen Performance 2.5.1 Standard Testing Conditions - Warm up time 20 minutes. - DC supply voltage +24V DC - Ambient temperature 20C -28C - Relative Humidity 30%-80% - Video signal 1280 x 1024 @ 60Hz; DVI-D - Ambient Environment Dark - Setting Set to Gamma 2.2 - Luminance meter Minolta CA-310 or equivalent factory preset 2.5.2 Brightness 2.5.2.1 Factory Settings Factory Preset (Gamma2.2 default,Gamma1.8,Gamma2.
SETTING3: Lmin<2cd/m² Lmax = 700±20cd/m² Max. Brightness: ≥800cd/m2 (adjust Backlight, Contrast and Brightness to Maximum) Test Condition: White Luminance (L max) is defined as a luminance of L255 Gray Level at the center point on LCD surface. Also Black Luminance (L min) is defined as a Luminance of L0 Gray level at the center point on LCD surface. (See Note 1 Note 4) 2.5.2.2 Gamma Curve Description Li=L0 + (i/255) gammax (L255-L0) Li is the desired luminance of graylevel i.
2.5.3 View angle Left/Right and Up/Down typical 170 degree (CR≥10) (Note 2) 2.5.4 Brightness Uniformity Deviation less than 30% (Note 5) 2.5.5 Contrast ratio The panel’s native contrast ratio should be at least 800:1. (Note 3) 2.5.6 Response Time Typical (Ton +Toff ): 30ms (Note 6) 2.5.7 Gamma Curve Within ± 10% tolerance of calculated value Factory Preset gamma value: CIE;DICOM; Gamma1.8, Gamma2.0, Gamma2.2 (Gamma2.
Note2: Viewing angle is measured as follow: Note 3: Definition of contrast Ratio (CR): Ratio of gray max (Gmax) & gray min (Gmin) at the center point of the panel.
Gmin: Luminance with all pixels black Note 4: Definition of Luminance of White: Luminance of white at center point.
3. OPERATING GUIDE 3.1 Keys assignment LED MENU UP DOWN EXIT Figure3 3.2 Key Functions without active OSD Menu Key Action Menu Activate OSD Down Analog Input auto balance Note: This choice is in case all the signal sources are available. If not, the signal on the any one input will be displayed. 3.
EXIT Except “Exit OSD” Menu One menu level upwards (Settings are retained) In “Exit OSD” Menu Return to main menu (Settings are retained) 3.4 Submenu Calls Press the “Menu” key while the OSD is active, the function icon will jump to next line. Pressing the “Up” key, the coordinate submenu will be selected. 3.5 Locking of OSD Menu Keys Action 1 time EXIT key Lock or unlock OSD 3 times Up key If the OSD is locked, it is only possible to select input source (see 3.1 section). within 3 seconds 3.
of the monitor. Color Setting1 Set desired Brightness level: Setting 2 Three fixed Brightness level are available Setting 3 The default value is: User Setting1: 500cd/m2; Setting2: 600cd/m2; Setting3: 700 cd/m2 While choose setting 1,2,3 state it will recall factory default Black level, Contrast, Backlight Display H Position 0…255 Shift picture direction Settings (Analog only) 0…255 Shift picture in vertical direction 0…100 Adjust the frequency and phase of the input signal.
Auto Adjust Auto-Color ON / OFF Automatically get input signal match with the monitor Auto-Config ON / OFF Automatically adjust the image display settings. (Analog only) Execute The selected auto functions are executed. Note: The quality of the function depends on the applied picture contents. To get better effect it is recommended to apply full screen picture and including white and dark contents.
Exit Reject changes Check reject changes or accept changes when quit OSD menu. Accept changes Quit OSD * Service level 2 enter: while the highlight line is on the service level 2 position, press 1 x Up, and 2 x Down keys, it will enter the following submenu. Service level2 LUT select and factory settings recall: Contrast; Brightness; Backlight; Setting1; OSD position; corresponding LUT factory recall. (The default state is Gamma2.2LUT) CIE Select Gamma CIE LUT DICOM Select DICOM LUT Gamma 1.
4. MECHANICAL SPECIFICATIONS 4.1 Outline dimensions & weight Figure 4 Item Set Size of set Last change: 2015-1-23 Width 425mm Height 350mm Housing components Aluminum Visible screen surface Approx. 376mm×301mm Ventilation slots In rear panel Degree of protection IP20 to DIN40050 VESA mounting 100x100 mm Net weight Approximately 5.
4.2 Screen Quality 4.2.1 H/V outline position H: |L-R|≤1.0mm V: |U-D|≤1.0mm 4.2.2 Outline edge position Last change: 2015-1-23 ∣A-B∣≤1.0mm ∣C-D∣≤1.0mm ∣E-F∣≤1.0mm ∣G-H∣≤1.
4.2.3 Structure width position ∣A-B∣≤2.0mm 4.3 Packaging Figure 5 4.3.1 Package dimension and weight Box Outer size of box Gross weight Last change: 2015-1-23 Width (mm) 545 Depth (mm) 195 Height (mm) 470 Approximately 7.
5. ENVIRONMENT CONDITONS 5.1 Operation Temperature Ambient temperature range 10 to 40 deg. C Ambient humidity 10% -80% (non-condensing) Temperature gradient Max. 5℃/h , no condensation Altitude 700 to 1060 hPa 5.2 Transport and storage (Packed) Ambient temperature range -20 -- +60℃ Ambient humidity 5%-90% Temperature gradient Max. 10℃/h, no condensation Altitude 70 – 106 kPa 5.3 Mechanical requirements Operation According to EN60068-2-6 Vibration 10--58 Hz within ± 0.
According to EN 60068-2-27 (single shock) Shock 250m/s2, 6ms(in storage packing) According to EN 60068-2-29 (permanent shock) 5.4 Drop Test (packed) Position Height Corner 1 76.0cm Edge 3,2,4 76.0cm A,B,C,D 76.0cm E 76.0cm F 76.0cm Surfaces (Cushion should be changed to new one.) Corner 5 76.0cm Edge 6,7 76.0cm Figure 6 5.5 Safety specifications Safety standards IEC 60601-1:2005, ANSI/AAMI ES60601-1:2005 ＆ CSA C22.2 No.60601-1:2008,EN60601-1，EN60601-1-2， GB4943.
Protection class Protection class I Degree of protection to IP 20 DIN 40050 Conformity CE 5.6 Electromagnetic compatibility 5.7 MTBF Flat screen without Backlight: 50,000 operation hours. Flat screen with Backlight: 30,000 operation hours. 6.
Last change: 2015-1-23 Copyright @Bigtide All rights reserved HL1936(HL1936SMT-L Page 27 of 37 /R internal) For GE
Last change: 2015-1-23 Copyright @Bigtide All rights reserved HL1936(HL1936SMT-L Page 28 of 37 /R internal) For GE
Last change: 2015-1-23 Copyright @Bigtide All rights reserved HL1936(HL1936SMT-L Page 29 of 37 /R internal) For GE
Last change: 2015-1-23 Copyright @Bigtide All rights reserved HL1936(HL1936SMT-L Page 30 of 37 /R internal) For GE
Other Issues which are not defined in these criteria, shall be discussed with both parties, Customer and Supplier, for better solution. Dust between LCD and touch screen : Items Dust Criteria Linear（mm） Circular(mm2) Last change: 2015-1-23 Copyright @Bigtide All rights reserved L≤5,N≤3 No dust gathered S≤0.05 0.05＜S≤0.2 0.2＜S≤0.3 S＞0.
7. NOTICE FOR HANDING Handing (1) When the module is assembled, it should be attached to the system firmly using all mounting holes. Be careful not to twist or bend the modules. (2) Because the inverters use high voltage, power should be disconnected before it is assembled or disassembled. (3) Refrain from string mechanical shock and /or any force to the module. In addition to damage, this may cause improper operation or the module and CCFT backlight.
Appendix 1 Preset Timings Detailed timing comply with VESA specification. Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (Horizontal/Vertical) VGA, 720 x 400 31.5 70.1 28.3 -/+ VGA, 640 x 480 31.5 59.9 25.2 -/- VESA, 640 x 480 37.5 75.0 31.5 -/- VESA, 800 x 600 37.9 60.3 40.0 +/+ VESA, 800 x 600 46.9 75.0 49.
VESA, 1024 x 768 48.4 60.0 65.0 -/- VESA, 1024 x 768 60.0 75.0 78.8 +/+ VESA, 1152 x 864 67.5 75.0 108.0 +/+ VESA, 1280 x 1024 64.0 60.0 108.0 +/+ VESA, 1280 x 1024 76.7 71.96 135.0 +/- VESA, 1280 x 1024 80.0 75.0 135.
