9" LCD MONITOR REV A2 User Manual 19" LCD Monitor HL1916AMT-L/R 1
19" LCD MONITOR REV A2 1. Application........................................................................................................................................................................3 2. Declarations ......................................................................................................................................................................1 Safety precautions ......................................................................................................
19" LCD MONITOR REV A2 1. Application This high-resolution color display is specifically designed to meet the rigorous performance standards needed for diagnostic, the left one with glass and right one with Touch screen interventional radiology, and other medical applications. To guarantee image integrity, features include accurate signal conversion and a wide range of interfacing options.
19" LCD MONITOR REV A2 Safety precautions Regular maintenance and calibration are recommended Please note that liquid crystal displays such as the HL1916AMTdo not have a failure rate of zero and image parameters may change over time (e.g. luminance or discoloration). Please ensure that all measures are taken to prevent injuries or incorrect diagnoses. Regular maintenance and calibration are recommended.
19" LCD MONITOR REV A2 TUV approval mark China Rohs symbol Danger: There is a danger to life if the warning information is not observed. Severe personal injury or damage to property may occur. Do not open the unit yourself. Only use a perfect power supply cable A damaged power supply cable may result in a fire or electric shock. When disconnecting the power supply cable, always do so by holding the plug.
19" LCD MONITOR REV A2 Take appropriate measures to particularly ensure that discharge currents remain below the required limits: Appropriate measures: - Disconnecting devices for signal input or output unit - Use of a safety transformer - Use of additional PE conductor Only use the signal cables and interface cables specified by the manufacturer for the installation. Use power cables with a PE contact. Only insert into sockets with a PE contact.
19" LCD MONITOR REV A2 Provide sufficient heat dissipation Slots are provided at the rear of the housing. The display must be placed or secured on a hard, level surface at least 10 cm from the wall and 15 cm away from other devices. Several displays can be butt-mounted horizontally and vertically. The following must be observed when mounting (VESA connection): Mounting screws Number 4 Thread M4 Strength 12 Immersion depth Min. 10 mm; Max. 12 mm Torque Max.
19" LCD MONITOR REV A2 3. Installation Provide adequate ventilation Ventilation slots are located on the rear of the housing. Ambient temperature The permissible ambient temperature range must not be violated. Minimize reflections The display should be positioned so that reflections of lights, windows, furniture with shiny surfaces or light-monochrome walls do not appear on the screen.
19" LCD MONITOR REV A2 4. Start-up Caution In order to ensure safe operation of the equipment, close attention must be paid to the information contained in this Instruction Manual as well as the warnings in Section 2 "Safety precautions". Caution Information for end customer None of the settings must be changed on site by the user, otherwise the guarantee is canceled. This also applies to settings made using the HL1916 AMT keys. These are therefore locked for certain applications.
19" LCD MONITOR REV A2 4.1.1 Little cover (removing) Remove the one screws with an M4 Slot screwdriver (one turn suffices). Open the little cover and remove it 4.1.2 Cable (attaching) Connect the cables to the display. Connect the USB cable . Connect the power cable .
19" LCD MONITOR REV A2 computer system using the Sub-D connector. The display is adapted using an OSD menu. DVI connection: The connection to the computer can also be made via the digital single link or via the analog channel of the DVI connection. The picture quality, noise immunity and radiated interference of the complete system depend on the cable quality and length. USB connection：you can connect the touch screen via the USB connector to the computer to control the touch screen.
19" LCD MONITOR REV A2 standard (see Section 6.1 "Picture adjustment"). Normally auto adjust will work. 4.4 Adjusting the brightness and contrast The brightness and contrast must be adjusted for the respective graphics card (different output levels) in the system on site. Note on adjustment − Use the SMPTE test pattern. − Adjust the brightness so that image sections with 5% and 0% blackness still visibly contrast from one another.
19" LCD MONITOR REV A2 5. Connections 5.1 Connecting the flat panel display Note All screening precautions contained in the corresponding EMC guidelines must be observed. If these guidelines are not observed, interference signals could penetrate the monitor. Information on cable installation Only screened cables are permitted for the signal connections. All connectors should be of screw or locking types (as far as possible). Signal and power cables must not be routed in the same duct.
19" LCD MONITOR REV A2 5.3 Information on additional serial interface (Service Only) Serial connection: you can connect the display via the RJ45 connector to the computer for firmware updating and monitor test. 5.4 Analog and digital inputs (DVI-D, VGA) 15-pin Sub-D connector Connect VGA cable with 15-pin Sub-D connector (male) for the analog input to the 15-pin Sub-D connector (female). DVI socket With DVI-D digital signal. 5.
19" LCD MONITOR REV A2 6. Adjustments 6.1 Picture adjustment This section describes the settings for operation of the flat panel display with a video source. The most important settings are: Adjusting the graphics memory of the video source As with all monitors, the flat panel display also has certain limits, e.g. maximum resolution and vertical frequency. The graphics adapter must be set when using the flat panel display such that the limits are observed.
19" LCD MONITOR REV A2 slightly until the display is just above the absolute lowest black level (one step is generally sufficient). Similarly, set the white level using a 100%-white test pattern and the measurement device. Only the contrast level should be adjusted to ensure that the black level remains unchanged. • Control again the black value did not change. In case it did you need to duplicate the two previous steps until it does not change anymore (cause: pedestal).
19" LCD MONITOR REV A2 active. 6.3.2Key functions without active OSD menu Key Action Menu Activate OSD Up Adjust Backlight Down Analog Input auto balance * Scenario in case all signal sources is available. If not, the signal from the next available source will be displayed. 6.3.
19" LCD MONITOR REV A2 Key(s) Action In a sequence Lock or unlock OSD If the OSD is locked, it is only possible to EXIT , Up, Up ,Up switch over the source (see Section 6.3.2). 6.3.6 Keys assignment and operation LED A “dynamic help for keypad function” is available for each menu: it explains the role of each key depending on the OSD menu window, which is currently active.
" LCD MONITOR REV A2 6.4 Description of the menus Main Menu Function Adjustment range 0…255 Adjustment of contrast This allows the brighter area to be seen more distinctly. The center point is in 128 position. Note: for DVI-D signals the Contrast setting is optimized. Manual changes are not recommended. Brightness 0…255 It is used to adjust the Brightness of the monitor. The center point is in 255 position. This allows the darker area to be seen more distinctly.
19" LCD MONITOR REV A2 Frequency (VGA only) Adjust the frequency and phase of the input signal. Phase (VGA only) Adjust phase of the input signal. DVI-IN VGA-IN(A nalog) Picture Source Auto function (Analog input only) Language AutoBalance Auto -Config On/Off On/Off Select source for main display When you enter this OSD menu the current source is highlighted. Following switch off and on of the display, the picture sources are searched one after another.
19" LCD MONITOR REV A2 You can make further settings for the picture source OSD—Hposition Others Service level 2 Adjustment of OSD horizontal position (Default state is on the bottom right corner of the screen) OSD—Vposition Adjustment of OSD vertical position (Default state is on the bottom right corner of the screen) Hot Key On/Off Enable or disable the Hotkey. The up key is used for brightness, down key is used for Auto Adjust.
19" LCD MONITOR REV A2 Quit OSD menu Accept changes Reject changes Quick OSD menu and either save or reject the changes. If you have reached this menu unintentionally, you can return to the main menu using the EXIT key. If this message is displayed, you do not have the authority to carry out the changes in the OSD menu. Please contact your servicing partner in this case.
19" LCD MONITOR REV A2 Fault No picture appears on the display, operation LED off No picture appears on the display, operation LED green blinking Fuzzy picture, interference in vertical lines Other faults –LED orange blinking Cause Remedy Power cable not inserted Insert power cable or incorrectly inserted No video signal Video source supplying a signal Check video cable not Check video source Scanning frequency phase incorrectly set or Adjust frequency and phase Loose plugs Plug cables in properly a
19" LCD MONITOR REV A2 8. Technical data All technical data are valid after a warming-up period of 2 hours. 8.1 Display Type Display area Picture diagonal Native resolution Pixel organization Pixel pitch Contrast ratio Horizontal viewing angle Vertical viewing angle Backlight Brightness Lifetime backlight TFT,color active matrix 376.32 mm x 301.056 mm 19" or 48 cm 1280 x 1024 (full-screen format) 3 vertical sub pixels 0.294 mm x 0.
19" LCD MONITOR REV A2 8.3 Electronics Multi-standard technology Timing recognition Video modes with resolutions less than 1280 x 1024 can be expanded to the TFT resolution, and thus utilize the full display area (like multi-sync CRTs). In the same way, resolutions higher than 1280 x 1024 can be reduced and then displayed.
19" LCD MONITOR REV A2 8.4.3 Serial interface RS232 Via RJ45 6pin 8.4.4 Timing Input Input Signals Analog Digital Horizontal frequency 31kHz -82kHz 31kHz -82kHz Vertical frequency 50.0Hz - 75.0 Hz (Non-Interlaced) 50.0Hz - 75.0 Hz (Non-Interlaced) Video Signal Analog RGB Digital RGB Sync. Signal Separate Sync. (TTL) Composite Sync. Sync on green TMDS Pixel Clock 25.0MHz -140.0MHz 25.0MHz -140.0MHz Input connector Mini D-sub 15Pin DVI-D 8.
19" LCD MONITOR REV A2 Left Side Rear Four keys for OSD menu, operation-LED •Power supply connection • DVI socket • 15-contact 3-row Sub-D socket • RS 232 sockets RJ45 6 pin •USB-B Connection 8.6 Mechanical design Housing components Aluminum Visible screen surface Approx. 376 mm x 301 mm Ventilation slots In rear panel Degree of protection (front) IP20 to DIN 40 050 Connection panel At rear, covered Weight: Without stand 6.
19" LCD MONITOR REV A2 Transport and storage (packed) Ambient temperature - 20 ... + 60°C range Temperature gradient Max. 5 °C/h Relative Humidity 10%-85%, no condensation Atmospheric pressure 500 hPa to 1060hP a 8.8 Mechanical requirements Operation Vibration Shock According to EN 60068-2-6 10 ... 58 Hz with ± 0.075 mm deflection 58 ...
19" LCD MONITOR REV A2 8.10 Electromagnetic compatibility IEC60601-1-2 FCC Class-B 9. Dimensional drawings All dimensions in mm. 9.
19" LCD MONITOR REV A1 10 Remarks and contact address Invalidity of guarantee All unauthorized electrical or mechanical alterations on or in the unit result in loss of the guarantee. Information on the Instruction Manual For clarity reasons, this Instruction Manual does not contain all detailed information on this product.
FCC Statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
