Model No. Número de modelo TC-50CX400U Owner’s Manual 50" Class 4K2K LED UHD TV (49.5 inches measured diagonally) Manual de usuario Televisión de alta definición de 4K2K clase 50" de LED (49.5 pulgadas medidas diagonalmente) For assistance (U.S.A./Puerto Rico), please call: 1-877-95-VIERA (958-4372) www.panasonic.com/help Para solicitar ayuda (EE.UU./Puerto Rico), llame al: 1-877-95-VIERA (958-4372) www.panasonic.com/help Register online at www.panasonic.com/register (U.S.
This product incorporates the following software: (1) the software developed independently by or for Panasonic Corporation, (2) the software owned by third party and licensed to Panasonic Corporation, (3) the software licensed under the GNU LESSER GENERAL PUBLIC LICENSE Version 2.1 (LGPL V2.1) and/or, (4) open sourced software other than the software licensed under the LGPL V2.1.
The terms HDMI and HDMI High-Definition Mutilmedia Interface,and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. Contents Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.
Safety Precautions Note to CATV System Installer This reminder is provided to direct the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
This equipment is a Class II or double insulated electrical appliance. It has been designed in such a way that it does not require a safety connection to electrical earth. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. This product contains electrical or electronic materials. The presence of these materials may,if not disposed of properly, have potential adverse effects on the environment and human health.
FCC and IC STATEMENT FCC Caution: To assure continued compliance, follow the attached installation instructions and use only shielded interface cables when connecting to peripheral devices. Any changes or modifications not expressly approved by Panasonic Corp. of North America could void the user's authority to operate this device. This product is restricted to indoor use due to its operation in the 2.400 to 2.
CEA CHILD SAFETY NOTICES WARNING Flat panel displays are not always supported on the proper stands or installed according to the manufacturer’s recommendations. Flat panel displays that are inappropriately situated on dressers, bookcases, shelves, desks, speakers, chests, or carts may fall over and may cause personal injury or even death. The consumer electronics industry (of which Panasonic is a member) is committed to making home entertainment enjoyable and safe.
Accessories/Optional Accessories Accessories Check that all the following items have been included with your TV Remote Control NZQAYB001013 Batteries (2) AA Battery Owner’s Manual Pedestals Assembly Quick Start Guide Screws M4 x 35 Warranty Card Optional Accessories Please contact your nearest Panasonic dealer to purchase the recommended optional accessories. For additional details, please refer to the optional accessories installation manual.
Attaching the Pedestals to TV A Assembly screws B Pedestal (R) (buttom) (4) C Pedestal (L) (50") (50") M4 x 35 B C A A Attaching the pedestals(For 50") Be sure to attach the pedestals in the following way. 1. Lay the TV face down on a flat, cushioned surface to avoid damaging or scratching. 2. Attach the pedestals B C to the TV with four assembly screws A provided. Removing the pedestals from the TV 1.Remove the assembly screws A from the TV. 2. Lift the TV from the pedestals B C .
Installing the Remote's Batteries Push open Close Note the correct polarity (+ or -). 1 2 Open the battery cover. Insert two "AAA" size batteries (supplied with the product). 3 Close the battery cover • Place the batteries with their terminals corresponding to the (+) and (-) indications in the battery compartment. Caution Incorrect installation may cause battery leakage and corrosion, resulting in damage to the remote control. • Do not mix old and new batteries.
Connections Connection Panels Back of the TV 1. DIGITAL AUDIO OUT Connect to the audio socket on the digital audio system. 2. USB Port Connect to a USB storage device to play compatible audio and photo files. (USB mode) 3. ETHERNET Wired Network connection port. 4. HDMI Inputs Connect to a High-Definition (HD) signal output device. 5. VGA Input Connect to a computer or other devices with a VGA interface. 6. PC AUDIO Input Connect to a computer audio output. 7. ANTENNA/CABLE IN Connect to the antenna. 8.
Antenna or Cable Connection Back of the TV VHF/UHF Antenna or Cable TV Power Cord Connect after all other connections have been made. VHF/UHF Antenna NTSC (National Television System Committee): Analog television system ATSC (Advanced Television Systems Committee): Digital TV Standards include digital high-definition television (HDTV), standard-definition television (SDTV), data broadcasting, multi-channel surround sound audio and interactive television.
AV Cable Connection Best To use HDMI terminals A (Set-top-box / DVD recorder / Blu-ray Disc player / Camcorder / etc.) HDMI cable AV Equipment white L R Audio cable red e.g. Blu-ray Disc player DVI OUT HDMI-DVI Conversion cable white AV Equipment HDMI AV OUT AUDIO OUT e.g. Blu-ray Disc player red To use COMPONENT terminals B (DVD recorder / Blu-ray Disc player / etc.
Audio Connection Optical cable DIGITAL AUDIO IN e.g. Amplifier with speaker system HDMI cable HDMI OUT (ARC) HDMI connection is available if connected audio equipment has ARC (Audio Return Channel) function. Panasonic does not guarantee operation and performance of peripheral devices made by other manufacturers; and we disclaim any liability or damage arising from operation and/or performance from usage of such other maker’s peripheral devices.
Identifying Controls TV Controls/ Indicators Front of the TV Remote control sensor Maximum range for remote is 23 feet (7 meters) from front of TV set Power indicator ( On:red; Standby:no indicator) Back of the TV VOL CH Volume up/down Selects channels in sequence MENU Displays the main menu and submenu INPUT /OK Selects the different input mode; press OK to confirm the seletion in menu POWER On/Standby button Note The TV consumes a small amount of electric energy even when turned off.
Remote Control Switches TV On or Off (Standby) Select among the different sources: HDMI1/ HDMI2(ARC)/ HDMI3/ COMPONENT/ AV/ PC/ USB/ ANTENNA/CBL Enter multiple program channel number such as 2-1 use for digital channels Accesses NETFLIX service directly • This service requires network connection. • This service might be stopped or the conditions changed without notice.
First Time Setup Connect the power cord to the power socket after you have completed all the physical connections.Turn the TV on with the POWER button on the right back of TV or on the remote, then the red LED indicator will illuminate. (TV) (Remote) or The first time you turn the TV on, it will go into the Setup Wizard. Please firstly finish the necessary setup and connection. Use buttons to select the desired language and press OK button to confirm, then select the desired Time Zone.
When pressing button to , use OK button to go back to Time Zone menu. 2.When choosing “No” and entering, there are two options Cable Service(No Box) and Over-the Air Antenna to choose. Either selecting Cable Service(No Box) or Over-the Air Antenna, a screen menu will pop up as below: Press Yes to scan the available channels, after auto program completed, press OK button to enter the Network Type Setup and set the available network.
Wired Setup Auto Get IP: Connect the Ethernet cable to the ETHERNET port on the TV and select Auto Get IP to connect the wired network. Manual Get IP: select Manual Get IP and input the IP address to connect the wired network. Wireless Setup Enter Wi-Fi Scan to choose the available wifi and press OK button to enter, then use buttons to input the password. Then select Return and press OK button to go back, select Finish and press OK to connect the wifi.
Customizing TV Settings STREAMING Press the MENU button to directly enter the main interface. The default setting is STREAMING. Press OK or button to enter APP section. Use buttons to navigate and select the desired App, and press OK button to enter. Press BACK button to exit STREAMING. NETFLIX Enjoys TV shows & movies streamed instantly over the Internet. YouTube YouTube your way on the best screen in your house. Discover, watch and collect the latest movies and TV shows in high quality 1080p.
MEDIA Press buttons to select MEDIA, and use OK or button to enter. Then press button to navigate and select the desired PHOTOS or MUSIC option and press OK button to confirm. Press BACK button to exit MEDIA. VIEWING PHOTOS When selecting PHOTOS, press OK button to select the disk type to enter. Then use buttons to navigate in the picture folder and select the desired photo, press button to display the photo.Press MENU button to display the function bar to set the picture playing.
LISTENING TO MUSIC When selecting MUSIC, press OK button to select the disk type to enter. Then press to navigate in the music folder and select the desired music, then a subscreen will pop up. Press display the photo.Press MENU button to display the function bar to set the music playing. Note: File format supported: MP3. buttons button to SETUP Press buttons to select SETUP, and then use OK or button to enter.
PICTURE Press buttons to select PICTURE menu and then press OK button to enter. Use the following picture options and then use buttons to set each option’s setting. buttons to select Cycle among picture mode: Standard/Cinema/Game Mode(in HDMI or VGA mode)/Custom/Vivid. Picture Mode Alternative: you may press the P.MODE button to select the picture mode directly. Allow the blue background to turn On/Off during weak or no signal Blue Screen conditions.
SOUND Press buttons to select SOUND menu and then press OK button to enter. Use the following sound options and then use buttons to set each option’s setting. Sound Mode Bass Treble Balance Digital Out Surround Sound Auto Volume Audio Language buttons to select Allow the selection of an audio-enhancement technique: Standard/ Music/Cinema/Custom. Alternative: you may press the S.MODE button to select the sound mode directly. Control the relative intensity of lower-pitched sounds.
Network Type Wired(Ethernet) Wireless Network Status Software Update Deactivate Netflix Deactivate Vudu Netflix ESN Select two types of network: Wired(Ethernet) or Wireless. Connect the Ethernet to the TV: Auto Get IP/Manual Get IP. Connect the TV to the wireless network through searching the available Wifi. Display the current information of network status: Subnet Mask/ Gateway/DNS Server IP address /MAC ADDR. Upgrade the TV software through the network.
Use 0-9 buttons to input the old password and then input the new 4-digit password. Re-enter new password for confirmation. Select to turn On/Off system lock. The following options (USA, Canada, Content Ratings Settings and Content System Lock Ratings Reset) will only be accessible when you turn the system lock on. Set the TV Rating: TV-Y, TV-Y7, TV-G, TV-PG, TV TV-14 and TV-MA. USA Select MPAA rating : N/A,G, PG, PG-13, R, NCMPAA 17,or X.
Menu Language Transparency VGA Setting Closed Caption TIME Other Settings Restore Default Select menu language : English, Français or Español. The default on-screen menu language is English. Select to turn On/Off OSD transparency function. Set the VGA setting: H-POS, V-POS, Clock, Phase or Auto. (VGA source mode only) CC Mode Select CC mode : Off, On or CC on Mute. Basic Selection: CC1, CC2, CC3, CC4, Text1, Basic Selection Text2, Text3, Text4.
Frequently Asked Questions (FAQ) Questions Answers How can I confirm that my TV is working properly? The TV has a built in Self Test. On the remote control, press MENU and scroll down and select HELP to access the TV SELF TEST. Run the test and follow the on screen instructions. Why doesn’t the remote control work? Check that the batteries are fresh, are of the same type and are installed with the correct polarity (+ & -).
Care and Cleaning First, unplug the power cord plug from the wall outlet. Display panel The front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaning cloth or a soft, lint-free cloth. If the surface is particularly dirty after cleaning up the dust, soak a soft, lint-free cloth in diluted, mild liquid dish soap (1 part mild liquid dish soap diluted by 100 times the amount of water), and then wring the cloth to remove excess liquid.
Specifications TC-50CX400 Power Source AC 120 V, 60 Hz Power Consumption (Rated power / Standby power) Display Panel 150 W / 0.5 W Panel System LCD panel (LED backlight) Screen size 50 ” class (49.5 inches measured diagonally) W × H × Diagonal 43.1 ” × 24.2 ” × 49.5 ” (1096.01 mm × 616.
Note 31
USA Only: Disposal may be regulated in your community due to environmental considerations. For disposal or recycling information, please visit Panasonic website: http://www.panasonic.com/environmental or call 1-888-769-0149. Sólo Estados Unidos: La disposición puede estar regulada en su comunidad debido a consideraciones ambientales. Para información sobre la disposición o reciclaje, por favor visite la página web de Panasonic: http://www.panasonic.com/environmental o llame al 1-888-769-0149.
