Installation Guide SHENZHEN PUTIAN YONGGAO NEW ENERG Y TECHNOLOGY CO.
Important Safety Instructions SAVE THESE IMPORTANT SAFETY INSTRUCTIONS CAUTION WARNING ATTENTION AVERTISSEMENT This manual contains important instructions for EV700. When using electric products, always follow basic precautions, including the following. 1. Read and follow all warnings and instructions before installing and operating the WPT charging station. Install and operate only as instructed. Failure to do so may lead to death, injury, or property damage, and will void the Limited Warranty. 2.
9. Do not use this product if the enclosure or the EV connector is broken, cracked, open, or shows any other indication of damage. 10. Use 105°C wire copper conductors only. 11. Do not operate EV700 in temperatures outside its operating range. For charging stations set to 16-48 A, the range is -22˚F to 122˚F (-30˚C to 50˚C). For charging stations set to 50 A, the range is -40˚ to 113˚F (-40 to 45˚C). 12.
: Cet émetteur doit être installé pour fournir une distance de séparation d'au moins 20 cm de toute personne. IC RF Radiation Exposure Statement Caution: This Transmitter must be installed to provide a separation distance of at least 20 cm from all persons. Important: Under no circumstances will compliance with the information in this manual relieve the user of his/her responsibility to comply with all applicable codes or safety standards.
Table of Contents Package Contents ...................................................................................7 Tools .............................................................................................................8 Location Planning.................................................. ...................................9 Electrical Requirements for Plug In...................................................11 Mounting the EV700 ..............................................................
Package Contents Notice: The EV700 Home charging station requires a NEMA 6-50 or 14-50 outlet. Contact an electrician if you do not have a NEMA 6-50 or 14-50 installed. Check the box to ensure you have the Quick Start Guide, this installation guide, and these parts: a. Charging station • Mounting Bracket • Input Cable (2 ft.) • Output Cable (18 ft./24 ft. optional) • Device/Mounting Bracket Joiner Screw b. Screws (4) and washers (4) c. User Guide d.
Technical Parameters MODEL: WPTAC-7KW-S18-TD, WPTAC-7KW-S24-TD, WPTAC-9KW-S18-TD, WPTAC-9KW-S24-TD, WPTAC11KW-S18-TD, WPTAC-11KW-S24-TD Product name: AC Wallbox Charging Station Shell materia: Metal plate Linear way: Lower incoming line, lower outgoing line External Dimension of:380*250*90mm Weight: 8.
Tools These additional tools will be helpful for a quick installation: a. A NEMA-6-50 outlet or NEMA 14-50 outlet b. Measuring Tape c. Pencil d. Stud finer e. Level f.
Location Planning Prior to installation, verify your site has a sufficient electrical capacity and suitable location for mounting. 1. Be sure the area you have selected to mount your EV700 has sufficient space to accommodate the device. See dimensions below. Input Cable: 2 ft Output Cable: 18 ft (24 ft optional) Depth: 3.5” inches Width: 9.8” inches Height: 14.9” inches CAUTION: The circuit in use must be rated for 125% maximum load. The EV700 is a continuous load device. 2.
3. This charging station is not suitable for use in hazardous locations. Do not install EV700 near flammable, explosive, or combustible materials. 4. Be sure to install this device in an area that is inaccessible to children. 5. Ensure that the EV700 is within range of a Wi-Fi signal. 6. Failure to install this device on a surface that can support the weight of the charging station, cables, and necessary cable movement could result in personal injury or property damage.
Electric Requirements for Plug In DANGER: SHOCK RISK. Prior to wiring, make sure to turn off circuit breaker to the 240 V outlet. Do not return power to outlet until installation is complete. Failure to follow this step could result in shock or electrocution. The homeowner should know the final amperage of the circuit and the expected charging rate available after activation. Discuss with your electrician or power utility company. 1.
Mounting the EV700 1. The bracket will need to be mounted independently of the EV700 charging device. Remove the joiner screw on the bottom side of the device to separate the bracket. 2. Locate the stud closest to the NEMA 6-50 (or 14-50) socket on which you wish to mount the EV700. The mounting bracket allows for vertical or horizontal screw installation. 2a. If your stud is visible, add an additional stud for horizontal and vertical screw applications. 2b.
Complete Installation 1. Hang the EV700 on the wall mounting bracket. 2 Reattach the device to the newly mounted bracket using the joiner screw once again. 3. Extend the cable to its full length to remove any kinks or tension. 4. Drape the charging cable over the top of the charging station and dock the connector in its holster. 5. Restore power to the circuit at the electrical panel. 6. Plug the charging station into the outlet. NOTE: Be mindful of the EV700 charging cable.
7. Watch to ensure that the front status light glows solid blue. (indicates standby mode) 8. When the EV700 is plugged into your EV the LED indicator will glow solid green. 9. Once the charger is activated the LED lights will blink green to indicate that a charge has been initiated. 10. In the event of a fault the LED light indicator will glow solid red. 11. The EV700 is now ready for use. See User Guide for details.
Operating the EV700 For Charging Once the EV700 is powered properly, the main LCD touchscreen displays amperage, input voltage, kWh, charge time, and temperature. The default charge activation settings for the EV700 are automatic and application operation - “Auto & App”. This setting allows you to simply plug the EV700 into your EV to begin charging, while also allowing operation via the App. Plug the EV700 into your EV to begin charging. The LCD touchscreen will now display live statistics.
To change the operation settings to a different type of charge activation, select the gear at the bottom left of the touch screen. To protect your EV700’s settings, a passcode must be entered before making any changes. The default passcode is 123456. Enter these numbers and touch the check mark at the bottom right hand of the number pad. Once you have entered the code the touchscreen will display three properties available for modifying - Current Settings, Binding Card, and Start Mode.
WPT App “App Only’” restricts the EV700 to begin charging by mobile app only. Plug the EV700 into your EV, and the touchscreen will prompt you to activate the charge on your mobile device. RFID “Card & App” restricts the EV700 to begin charging only by RFID card, or mobile app. Plug the EV700 into your EV and the touchscreen will prompt you to activate the charge by swiping or using your mobile device.
Limited Warranty Our Promise This Limited Warranty for WPT EV700 Home Electric Vehicle charging station (“Warranty”) applies to you, the original purchaser of a new TURNONGREEN EV700 charging station (the “charging station”) from TURNONGREEN solely for use by you at your residence. This warranty is not transferrable and is valid for purchasers located in the U.S.A. and Canada only.
Important 1. You are responsible for the proper installation and maintenance of the charging station including the un-installing of any defective charging station and the installation of the repaired or replacement charging station returned to you. 2. Any service or repairs beyond the scope of the Warranty above will be performed upon customer approval at WPT then prevailing labor rates and other applicable charges. 3.
IN ADDITION: The Warranty on your charging station shall not apply if the original identification markings (for example, serial numbers and trademarks) have been defaced, altered or removed or if the charging station is used or installed for any purpose other than for use at a single family residence. WPT SPECIFICALLY DOES NOT WARRANT THAT ANY WPT SERVICES WILL BE ERROR FREE OR WILL OPERATE WITHOUT INTERRUPTION.
Additional Information This Warranty shall be governed by and construed in accordance with the laws of the State of California, U.S.A., exclusive of its conflict of laws principles. The U.N. Convention on Contracts for the International Sale of Goods shall not apply.
