XV-1 User’s manual 2K helmet camera V1.
Product Specification Sensor SONY IMX307 Aperture F1.8 Lens Angle Front: 140° Photo JPEG Video MP4 Resolution QHD 2560 X 1440P 30fps FHD 1920 X 1080P 60fps Waterproof IP66 Battery 1500 mAh Note：3-4 hours working time at full charge. Size / Weight D32.8 x 100mm / 98.5g Memory card TF card Max.
Product Structure ❶ Power button ❷ WIFI indicator (blue light) ❸ Recording button ❹ WIFI button ❺ Reset ❻ TF card slot ❼ USB charging port ❽ MIC
Key buttons commands 1. To power on / off: Press and hold the ❶power button for 3 seconds, and the camera will vibrate. 2. To start / stop recording: Short press the ❸recording button ONCE. 3. To turn the WIFI on / off: (First, stop recording.) Short press the ❹WIFI button TWICE. 4. To format the TF card: (First, stop recording and turn off the WIFI.) Quick short press the ❸ recording button 5 times . Note: If the camera can't detect or read the TF card, the 2 lights are flashing alternately.
Intelligent Energy-saving System 1. When the camera does not detect any motion for 3 minutes, it will automatically turn off. 2. When an external power supply is connected, the energy-saving system will be disabled. 3. This feature can be turned on/off in the APP's setting page. Insert the TF card 1. Open the cover of the TF card slot. 2. Insert a Class 10 or above TF card and the Max. storage is 128G. Please make sure to insert the TF card in the right direction and cover the card slot. 3.
Step 2 Step 3 Step 4 See instructional video here:
2. Using the APP: install the LOOKING CAM APP and connect your phone's WIFI to DB-1's WIFI, then go to the APP's setting page and format the TF card.
Step 3 See instructional video here:
Using the Camera 1. Before use, make sure that the camera is fully charged, and the TF card is inserted. Note: The TF card must be formatted when using it with the camera for the first time. 2. Long press and hold the ❶power button 3 seconds to turn on the camera, and it will vibrate once. 3. Once the camera is turned on, the recording light (green light) remains on (meaning, it's not recording), then it will automatically start recording. The green light will flash during recording.
Use the APP via WIFI 1. Download the LOOKING CAM APP. 2. After turning on the camera, press the ❹WIFI button TWICE to turn on its WIFI. Once the WIFI is on, the blue WIFI indicator light will flash. Note: If the camera is not connected to the phone within 1 minute, the camera's WIFI will automatically turn off. If the camera successfully connects to your phone, the camera's blue WIFI indicator light will remain on (not flashing).
3. Go to your phone’s setting page , click the camera's WIFI and enter the password to connect to it. The camera's WIFI name is DB1+SSID NO. and the password is 12345678 Note. Please DON’T change the WIFI name nor the password to avoid connection errors. 4. Once the camera's WIFI is connected to your phone's WIFI, open the LOOKING CAM APP and follow the on screen instructions to add the camera to the APP. 5. If successful, you'll see the camera in the LOOKING CAM app.
memory card. Format the memory card by pressing the ❸recording button 5 times, then connect again. Q3: The camera turns off automatically. A: (1) Please check if the memory card is inserted properly? (2) The camera has a 3 minute energy saving detection feature. If the camera detects no movement for 3 minutes, it will automatically turn off to save power. Q4: Updating the Firmware of the camera.
FCC Warning Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
