User's Manual

Bluetooth Headset
USER MANUAL
Left ear picture LRight ear picture R
The F10 earbud is designed for both ears. It will
be very comfortable for you whether you wear it
in your left or right ear.
Comfortable wearing
If the range between the Bluetooth and device
is more than 10 meters, the sound quality will
be terrible and headset will be constantly cut in
and off. In this condition the headset should be
be repaired with your device. If they can’t be
repaired, please select the Bluetooth name of
the headset in settings to repair.
To reduce the battery consumption, if there has
been no connected devices in the effective
range of headset within 5 minutes, the headset
will be automatically shut down.
Usual Connection
5 minutes
＞10 meters
Search
FOCUSPOWER-F10
Connection
Bluetooth
?
Long press
the button
for 6 seconds
Turn on: Long press the multifunction button for 3
seconds with voice promoting "power on" and the
blue light flashing for one time.
Turn off: Long press the multifunction button for 5
seconds with voice promoting "power off" and the
blue light flashing for 4 times.
3. Select "FOCUSPOWER-F10" from Bluetooth device
list. Please type in"0000" if password is required. The
blue light will go out and voice will prompt“Connected” if
connection is completed.
Turn on/off the headset
Play and pause music
Press the multifunction button.
Answer and end calls.
Press the multifunction button.
Reject the incoming call
Long press the multifunction for two seconds.
Re-dail
Double press the multifunction button.
Press the multifunction button for two seconds, then
you can go back to the previous call.
Double press the multifunction button, the previous
call will be hung up.
1. Long press the Multi-function button for "6"
seconds until voice prompts "ready to pair". Now the
blue indicator light is shining. (Attention: Don't loosen
your finger when you hear "power on"）
2. Activate the Bluetooth on mobile phones or
computers, then search and add new Bluetooth
device in the menu.
IOS terminal Settings > Bluetooth > Turn on
Different devices may lead to different operation
interfaces.
5. The headset supports multipoint connection(one for
two). You can pair it with second mobile phones at the
same time and answer calls from either one.
Turn off the headset after it’s successfully paired with
the first mobile phone.
Long press the multifunction button for 5 seconds to
pair with the second device.
Then select "FOCUSPOWER-F10" in the Bluetooth
menu of the second device. At last the two devices
have been connected with the headset.
4. The second time you connect the headset with the
device which has already been connected to the F10
previously , you needn’t repeat the above steps, the
headset will automatically enter the pairing mode when
you turn it on.
Switch to another call when making a phone
call
Answer a current call while making a phone
call
Basic Operation
Pair and connect
The effective
range is within
10 meters
1
2
To ensure safety, please note two points below:
1. Please stop charging the headset when it has already
been fully charged.
2. Please keep the headset off when it's being charged.
When the voice prompts "battery low", the headset
needs to be charged. When it’s being charged, the
blue light will come on. When it’s fully charged, the
blue light will go out.
Generally speaking, it will take 30-60 minutes to fully
charge the headset. However, the charging time will
make a difference if you use different USB-adapters.
To preserve the battery capacity and life, please don’t
keep charging the headset too long.
The current battery level will be displayed on the
device, you can check it anytime and anywhere.（
Some Android phones don’t support this function)
Charging
battery low
Search
FOCUSPOWER-F10
Connection
Bluetooth
2h 3h 4h ...
30-60
minutes
Android terminal Settings> Turn on Bluetooth
>Search
Search
FOCUSPOWER-F10
Connection
Bluetooth
Thank you so much for choosing FOCUS-
POWER product. Please read the following
safety and operational instructions before
using your headset/headphones and
accessories. Please keep these instructions
for your reference. This symbol identifies and
alerts the user to the presence of important
General
Important Safety and
Operational Information
Operating, storage and charging temperature is 0℃
to 40℃（32℉ to 104℉）.
Warnings
Exposure to high volume sound levels or excessive
sound pressure for a long time may cause temporary
or permanent damage to your hearing. You should
always use your headset/headphones with the
volume set at moderate levels.
Observe all signs and instructions that require an
electrical device or RF radio produce to be switched
off in designated areas, such as gas/refueling
stations, hospitals, blasting areas, potentially
explosive atmospheres, or aircraft.
This product is not a toy. Never allow children to play
with the product - small parts may be a choking
hazard.
Install and use eartips and earbuds in accordance
with the instructions provided. Do not force eartips
or earbuds down the ear canal. If either becomes
lodged in the ear canal, seek medical attention
immediately.
If the product or charger: overheats; has a damage
cord or plug; has been dropped or damaged; has
been dropped into water, disconnected any charger
from its power supply, discontinue use of the
product.
To avoid the risk of electric shock, explosion, fire or
leakage of corrosive or toxic chemicals, observe the
following charging and battery warnings. Charge the
headset/headphones according to the instructions
supplied with the unit.
NOTE: This equipment has been tested and f
ound to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions,may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
F10
！
FCC ID:2AWWT-F10