User's Manual

WIFI controller
Voice and intelligent speaker
control
Timer switch
Full range of W/ W + WW/RGB
/ RGBW/RGBW available
5-100% stepless dimming
Remote controllable after
connecting to internet
Features
WIFI controller
LED strip
Installation instructions
Attentions
1. Use DC12-24V power supply.
2. Install the WIFI controller correctly.
Use 3M tape to fix it
3. Please unfold the LED strip to avoid the overheat issues.
Please connect the cables of LED strip with the right position
on the controller. Test the APP to check if it can control the LED
strip correctly. If everything goes well, just keep going.
4. Check and ensure the power supply, WIFI controller and LED
strip are connected correctly.
1. Do not put any metal around the WIFI controller, which could
blocked WiFi signal
2. Ensure power supply and controller are connected correctly.
3. The power supply output voltage should be same as LED strip
working voltage.
4. Do not cover anything on the surface of power supply, WIFI
controller and LED strip.
5. Ensure the connection is correct before powering.
APP function introduction
Third party control
In the Smart Life APP: Find more service in "Me" menu, click to enter
“voice service”
(Alexa/ Google Assistant) and other services, click on the service you
need.
Connect to the third-party service device according to the operation
guide.
Remote control: The LED strip can be controlled anywhere after the
smart device is successfully connected.
Timer function: Set the timer to turn on and turn off the LED strip.
Intelligent scene: The system sets a variety of intelligent scenes, and
different scenes correspond to different lighting atmospheres.
Group: Group control is available (only for the same type of product).
Family room management.
Device Sharing: The device is shared with other user control devices in
the home.
Click the interface to control it according to the specific mode of the
specific LED strip.The following is public function introduction.
User Manual
1. Please confirm that the phone and controller are in the same WIFI environment;
2. Please confirm that WIFI is in 2.4G signal mode;
3. If the WIFI signal is in 5G mode, please click "compatibility mode" in the upper
right corner of the "confirm the light is flashing" page.
For any product and APP updating,please contact with customer service.
Log in / Register account number
Open the Smart Life APP, sign up for a new account or log in with an existing
account.
1. Preparation: Turn on the LED strip and enter the home of APP while
ensure the WIFI signal is good and stable.
2. LED strip will flashing when turn on the power supply. Add all devices
on the APP and enter adding lighting device interface, match LED strips.
3. If the LED strip is not flashing when turn on the power supply, long press
the Reset button for more than 5 seconds. While LED strip flashing, enter
the APP adding lighting device interface, match LED strips.
4. Select the Wi-Fi connected to the smart device, input the WiFI password,
and then click "OK" to wait for the matching to succeed.(Make sure smart
devices share the same WiFi)
1:DC12-24V input connection port
2:Output connection port to connect to LED strip(4-6PIN female
bracket/5PIN male PIN connector)
3:
Function buttons:
Switch on
Switch off
Long press for more than 5 seconds to reset
45 mm
195 mm
130 mm
150 mm
Product functions diagram
Music :External microphone receives sound
Item.NO
TYWFC3-41
TYWFC3-42
TYWFC3-43
TYWFC3-44
TYWFC3-45
CCT
W
Colour
RGB
RGB+W
RGB+CCT
Input Voltage
12-24Vdc
12-24Vdc
12-24Vdc
12-24Vdc
12-24Vdc
Power
Max.48W
Max.48W
Max.48W
Max.48W
Max.48W
Current
2A*1CH Max.2A
2A*2CH Max.2A
2A*3CH Max.2A
2A*4CH Max.2A
2A*5CH Max.2A
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception,which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
ÿ Reorient or relocate the receiving antenna.
ÿ Reorient or relocate the receiving antenna.
ÿ Reorient or relocate the receiving antenna.
ÿConsult the dealer or an experienced radio/TV technician for help
important announcement Important Note:
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed
and operated with minimum distance 20cm between the radiator and
your body.
This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.