User's Manual

Tuya DIY
Smart WIFI+IR Digital Music Lines Kit
User Manual
Features
DIY intelligent splicing scheme, which can be spliced according to
customer needs.
Cool lighting effects, colorful, flowing water, rainbow, Ambilight and
other transformation modes.
WIFI+BLE+IR protocol with APP+Remoter control.
12V low-voltage power supply, and uses any single product as the
power supply for the overall shape. Classic appearance and compact
structure. It can be spliced with different shapes and is easy to install.
Product Size
Installation Instructions
10
Styling reference
Product function diagram
Music Mode
Single click to switch ON
Double click to switch OFF
Single click mode
Long press for 5 seconds to reset
Plug
Connector
Brightness
1: Unpack the package and check whether the appearance is intact, and
whether the number of accessories is correct:
Figure Ś Remove the protective cover of the controller and the lamp IN-
interface, and then install the connector of the controller The connector is
aligned with the OUT of the controller.The bumps are aligned with one end
of the single notch of the connector. (Bump to Notch) Figure ś(The yellow
slant of the connector clip and the orange slant of the controller are close to
each other and then pressed down diagonally).
Note: Press down on the side of the suspension to remove a single connector.
When two lamps are connected together, grab one lamp and lift it up
to remove it, and then remove the single connector.
3: Take out the first one according to the shape, install connectors on both
sides, and deduct the OUT direction to connect position the protective
cover, then take out the connector to connect one end of the single notch
of the clip is connected to one end of the lamp OUT. (Bump to Notch)
(The yellow slope in the diagram of the connector buckle and the orange
slope on the controller are close to each other, and then press down
diagonally.) Figure ş Attach the connector at one end of the two notches
in the IN direction with same way.
4: Determine a position according to the shape, tear off the double-sided
adhesive red centrifugal paper on the lamp, align the adhesive surface on
the wall to be installed, press hard and install the first piece, and then install
the rest according to the shape. Determine whether to use screws for
reinforcement according to the user's usage scenario. The reinforcement
position is as shown in the figure. At the middle oval hole of the buckle, the
whole set needs to be reinforced, and the user decides by himself. Figure Š
Note: (one inlet, three outlets) - the OUT port of the lamp must be connected
to the IN port of the next lamp.
5: The second one of the modeling starts, just install the connector on the
OUT port, and tear off the red centrifugal paper on the lamp. When installing,
the width of the lamp should be aligned with the previous lamp, and the
inclined surface of the IN interface of the lamp should be aligned with the
inclined surface of the buckle, and then press down firmly. Figure š Refer
to Figure Š to see if screw reinforcement is required, and install the
remaining few in the same way. The last part of the shape does not need
to buckle the protective cover, and does not need to install the connector.
6: Finally, tear off the double-sided tape of the controller, buckle the connector,
and install the controller on the connector of the first head. Installation is
complete. Figure Ţ Plug the adapter into the DC socket of the controller
and start the experience. Figure ţ
2: In the same way, align the IN-port of the lamp to connect, plug in the adapter
to light up, and test each one. Figure Ŝ Take out the double-sided adhensive,
tear off one side of the white centrifugal paper, and stick it to the square position
on the back of the lamp(controller). Figure ŝ And design the shape and place
it according to your own preferences. Figure Ş Check if there is a problem
with the lamp. Pay attention to the running mode of the light, which is related
to the position of the controller. It is recommended that the controller be
designed in the head position.
Parameters
Model Colour
Voltage
Power Control
10WDC12V
RGBIC
FWWSA8-23-6
Parts List
Adapter x 1 3M glue x 13 Connector x 8
Manual x 1 screw x 8 Remote Controller x 1
Adapter x 1 3M glue x 19 Connector x 11
Manual x 1 screw x 11 Remote Controller x 1
Adapter x 1 3M glue x 25 Connector x 14
Manual x 1 screw x 14 Remote Controller x 1
14WDC12V
RGBIC
FWWSA8-23-9
18WDC12V
RGBIC
FWWSA8-23-12
Remoter+control
Remoter+control
Remoter+control
1
2
5;:5;:
6
/4
3
4 5
8
9
/4
5;:
5;:

7
5;: