8' W x 8' H or 10' H Peak Style Shelter Assembly Instructions Description 8' x 8' x 8' Peak Style Shelter - Gray 8' x 8' x 10' Peak Style Shelter - Gray Recommended Tools Please read instructions COMPLETELY before assembly. This shelter MUST be securely anchored. THIS IS A TEMPORARY STRUCTURE AND NOT RECOMMENDED AS A PERMANENT STRUCTURE. Before you start: 2+ individual recommended for assembly, approximate time 3 hr. 1-800-524-9970 150 Callender Road Watertown, CT 06795 www.shelterlogic.
ATTENTION: This shelter product is manufactured with quality materials. It is designed to fit the ShelterLogic®, LLC custom fabric cover included. ShelterLogic®, LLC Shelters offer storage and protection from damage caused by sun, light rain, tree sap, animal - bird excrement and light snow. Please anchor this ShelterLogic®, LLC structure properly. See manual for more anchoring details. Proper anchoring, keeping cover tight and free of snow and debris is the responsibility of the consumer.
8'W x 8'H Peak Style Frame Assembly Please read and understand instructions completely before assembly. Layout out frame parts as shown.
8'W x 10'H Peak Style Frame Assembly Please read and understand instructions completely before assembly. 18 TOP RAIL Layout out frame parts as shown. 24 8 MIDDLE RIBS 18 7 13 24 19 11 24 16 5 19 1 4 END RIB 19 4 17 3 17 8 20 3 25 24 25 20 5 1 16 25 14 5 12 15 25 UPRIGHT EXTENSION, 27” SWEDGED-1 SIDE 1 5/8 D.
ASSEMBLY OF PEAK STYLE GARAGE SHELTER NOTE FOR FRAME EXTENSION KIT: 8’ x 8’ is the base frame dimension. Your model may have more middle ribs than shown in the illustrations. You will receive one extra rib for every extra 4 feet of building length that you purchase. The basic frame assembly will remain the same. The cover will be the correct size for the length of the building ordered. 8' 1. Plotting and squaring up the Frame: A.
3. Install Side Rails and ShelterLock™ Stabilizer Blocks: A. Place assembled first end rib in the staked area. Place the ShelterLock™ on the upright as shown in Detail D. From the outside of the rib insert the bolt through the upright and then through the ShelterLock™. B. Place the plain end of the side rail over the bolt and nest it into the ShelterLock™. Install the nut onto the bolt and tighten. Repeat these steps for the opposite side and all of the remaining ribs.
5. Install Top Rail: Place the first top rail under each end rib and secure it with a bolt as shown in Detail F. The same cross rail should lay on top of the all middle ribs. Secure the rails to the frame with the hardware indicated in Detail F. The top rail attached to the last rib will be installed under the pipe. Install the Top Rail OVER all Middle Ribs DETAIL F 10115 802630 6. Properly Anchor the Frame A. Anchors must be placed inside shelter at the corners of the shelter. B.
7. Door and solid End panel installation A. Hold end panel at the top center with white inner surface facing inside of the shelter. Wrap the edges of the fabric panel around the end rib. B. Disconnect top rail from the end rib. Pass the top cross rail through the gap in the fabric, in between the webbing and rib frame. Re-attach top cross rail to end rib. Repeat Step B for side cross rails. C. If this connection has the wind brace on it remove the wind brace end before pulling the side rail.
8. INSTALLING COVER AND COVER RAILS A. Lay the cover on the ground next to the frame with inside of the cover (the side with the pipe pockets) facing down and the webbing on the front and rear of the corner of the building. B. Pull cover over the frame, making sure to center cover on frame. There should be an equal amount of over- hang at all four corners. C. Insert the “S”- Hook on ratchet into hole on the leg bend. Insert the webbing into the spindle of the ratchet and pull tight.
