Technical data

ManualsBrandsShelter Logic ManualsSport & travel14'W x 7'H

OFF GRID

Xtender Accessories

310

500

220

Remote control and

programming centre RCC-03

Thanks to its graphic display it provides many understandable indica-

tions on the state of the system.

The remote control memorises and displays the events that occurred

on an installation and so it does anticipate the problems that might

appear.

It gives access to the many adjustable parameters of the Xtender like the

setting of the charge curve of the battery, the programming of the auxi-

liary relays or even, among others, to a lot of operation options.

A place is dedicated to a SD card which will allow the parameters memo-

rising, the data transfer or the software update.

Battery temperature sensor BTS-01

This sensor enables to accurately adapt the charge thresholds to the

battery temperature.

Communication module 3ph and parallel PEM-01

Allows the setting in parallel or the implementation of a 3-phase system

even when only a single-phase source is available.

Communication cable for 3ph and parallel

CAB-RJ45-2 (2 m)

Allows the setting in parallel or the implementation of a 3-phase system

even when only a single-phase source is available.

62|

|63

Xtender XTH

3000-12, 5000-24, 6000-48, 8000-48

The serie Xtender offers a new function, the Smart-Boost,

which enables to add the inverter power to another sour-

ce, like for instance a genset or the shorepower, even

in case of asymetric loads. It is also possible to add an

Xtender to almost any other existing inverter in order to

increase the power available.

The products of the Xtender-Series provide an unmat-

ched freedom of use, thanks to their many functions. In

a basic application, they offer together the functions of

inverter, battery charger, transfersystem and assistance to

the source.

These functions can be combined and controlled in a to-

tally automatic way for an exceptional comfort and an

optimal management of the available energy.

By the implementation of several units, it is possible to

create a 3-phase source or to set them in parallel to in-

crease the power available. Up to 9 inverters of the serie

Xtender shall therefore be combined together (see page

49).

The programmable auxiliary contacts allow as well the

inter connection with existing systems or the implemen-

tation of extended functions. Fully programmable by

means of its remote control, it enables the update of the

software, making it an upgradeable product.

Features

Possibility to connect up to 3 Xtenders in parallel

Three-phase systems with up to 9 Xtenders

True sine wave voltage

Reliable and noiseless with any kind of load

Outstanding overload capabilities

Function Smart-Boost for assistance to the source

even with difficult loads

Automatic reduction of peak loads (power shaving)

Automatic allocation of the power available

(power sharing)

Standby level adjustable over a large range

and from a very low threshold

Multi-stage programmable 4 STEP battery charger

with PFC

Ultra-fast transfer relay

High efficiency

Ultra-fast regulation

Control by digital signal processors (DSP)

Full internal protection.



Model XTH 3000-12 XTH 5000-24 XTH 6000-48 XTH 8000-48

Inverter

Nominal battery voltage 12 V 24 V 48 V 48 V

Input voltage range 9.5 - 17 V 19 - 34 V 38 - 68 V 38 - 68 V

Continuous power @ 25 °C 2500 VA 4000 VA 5000 VA 7000 VA

Power Smart-Boost 2500 VA 4000 VA 5000 VA 7000 VA

Power 30 min. @ 25 °C 3000 VA 5000 VA 6000 VA 8000 VA

Power 5 sec. @ 25 °C 3 x Pnom

Load detection (standby) 2 to 25 W

Cos ϕ 0.1 - 1

Max. efficiency 93 % 94 % 96 % 96 %

Consumption OFF/standby/ON 1.7 W / 2.2 W / 14 W 1.8 W / 2.5 W / 20 W 2.2 W / 3 W / 22 W 2.2 W / 3.8 W / 34 W

Output voltage 230 Vac (- 10 % / 0)

Output frequency 50 / 45-65 Hz +/- 0.05 % (crystal controlled)

Harmonic distortion < 2 %

Overload and short-circuit protection Automatic disconnection with 3 time restart attempt

Overheat protection Warning before shut-off - with automatic restart

Battery charger 6 step adjustable : I-U-Uo-Equalize-Uo(low)-U(periodic)

Charging current adjustable 0 - 160 A 0 - 140 A 0 - 100 A 0 - 120 A

Input current balance adjustment 1 - 30 A 1 - 50 A

Max. input voltage 265 Vac

Input AC voltage range Adjustable threshold from 150 to 230 Vac

Input frequency 45 - 65 Hz

Power Factor Correction (PFC) Yes, according to EN 61000-3-2

General data

Multifunction contact adjustable 2 independent contacts 16 A 250 Vac (potential free 3 points)

Max. current on transfer relay 30 A / 6.9 kVA 50 A / 11.5 kVA

Weight 34 kg 40 kg 42 kg 46 kg

Dimension h x w x l 220 x 290 x 500 mm 220 x 310 x 500 mm

Protection index IP 23

Operating temperature range -20 °C to 55 °C

Ventilation Forced from 45 °C

Acoustic level < 10 dB / < 35 dB (with / without ventilation)

Sine

Wave Inverter

Multifunctional contacts

The potential free contacts can be programmed to provi-

de many supplementary functions.

They can react to each event, inside or outside of the

inverter (presence of the grid, battery thresholds, alarm

signal). The contacts can also be programmed as time

switch or can be disabled during sensitive periods (night,

weekend). They allow therefore the implementation of

functions like the automatic start of gensets, the auto-

matic disconnection of second priority users, the alarm

signal, the conditional charge of the battery, etc.

Technical data

COMSHS VPS RV HYBRID UPS

Sine

Wave Inverter

Power class 3,000 W - 72,000 W

0 W 25,000 W 50,000 W

100,000 W

5,000 W

Function Smart-Boost

The function Smart-Boost enables to add the inverter

power to another source, like for instance a genset or the

shorepower, even in case of asymetric loads. It is possible

to add an Xtender to almost any other existing inverter in

order to increase the power available.

75,000 W