Operating instructions

Display:
HS1 03-53
Display:
0000
Display:
CALL LOG
Display:
DELETE HANDSET
Display:
0000
Display:
HS~
Then input register pin code like PIN 0000 (pressing button to erase if any error)
>>Press button to confirm, once registration succeed, a sound of “di du du” can be
heard and the screen will display:
>>Long sound of “bi bi” will be heard and screen displays BASE 1 and keep blinking
if fail in registration, this device will return to standby mode automatically 2 seconds
later and it is required the registration again.
>> To activate the additional handset(s) (if available), the repeat operation is required
as above (max link up to 5 handsets); once the registration succeed, then the screen will
display HS2 or HS3 accordingly.
B: deregistration (base unit and handset)
Note: it is not recommend to do the deregistration unless the link-up between handset
and base is lost permanently.
Handset Deregister
(applicable to multi handsets only)
>>at standby model, Press button till screen displays
>>Press or button to select BS SETTINGS
>>Press button and the screen displays
>>Press button and it displays PIN? Input registration pin code like PIN 0000
(note: 0000 is the defaulted pin code on this device)
>>Press button to enter handset deregistration setting mode,
press or to select handset to be deregistered.
>>Press button to confirm, a sound of “di du” will guide you the successful
deregistration done, or else a sound of 'bibi” heard to indicate the deregistration is
failed (Note: the original No.1 handset are restricted to do deregistration)
>>Press button to turn into standby mode
Base Deregister
>> at standby mode, press and hold PAGE button continuously up to 5S'till
LINE BUSY LED blink, fast press PAGE button intermittently for 7 times and
then the LINE BUSY LED will get blinking fast, until LINE BUSY LED turn
off. It indicates that the deregistration succeeds.
(NOTE: the operation is effective only under fast operation of the pressing)
Display:
BASE SETTING
Display:
BASE 1
To register and deregister
Note : the registration has already been done on this device when ex-factory, antenna
icon will appear at the top of right corner while handset power on. While antenna icon
is steady on display, it means handset has linked up with base unit.
If antenna icon blinks long time on display, it means lost linking with base units, you
are required to re-register the handset. process as below:
1).on base unit, press button to start registering mode, base will give a beep tone
PAGE
2). press button on handset to enter menu setting mode, then press button
with red LED start blinking (if more 2 minutes and register not suceed , blinking will stop,
you need to re-press "PAGE" key again) .
to find "Registration" menu,
3). press button to start handset registering mode, handset will display "searching",
4). if handset find base unit, display will show "PIN CODE", blinking cursor will guide to input
pin code 0000(default value).
5). if registration is sucessful, handset will give a long beep tone, then antenna icon is steady,
display will show , it means it is the first handset of the base unit.
1
6 ). if registration is not sucessful, handset will return to searching status, you need to try again.
To register a handset
To select a base unit
The handset can be registered to different base (up to a maximum of 4) at same time,
and you can select which base you want the handset to operate with.
If you select "AUTO" the handset will link with the first of the registered
bases that it finds.
To de-register a handset
You may need to do this if you need to replace a faulty handset.
In standby mode, press  button to enter setting mode.
1).
2).
press or button to select "HS SETTINGS",
3).
press button to enter handset function setting,
4).
press or button to find "SELECT BASE",
5).
press button to enter next step, handset will show "BASE 1,
6). press or button to scroll " BASE 2", "BASE 3", "BASE 4", "AUTO"
if base number followed " ", it means handset had been registered on this base,
7).
press button to confirm, then handset link up to your desired base unit.
~13~
In standby mode, press  button to enter setting mode.
1).
2).
press or button to select "BS SETTINGS",