Instruction Manual

1Printed in China.
READ ALL WARNINGS AND PRECAUTIONS BEFORE USE
SAFETY WARNINGS
• Not recommended for children under 14 years of age. As with all electrical products, precautions should be
observed during handling and use to reduce the risk of electrical shock.
• Adult supervision is required at all times.
• Drive drone only on smooth flat surfaces.
• Never fly drones above or near people, sudden changes in wind or other conditions could lead to unexpected crashes.
• Always use caution when flying drone vehicles, obey relevant laws, respect the privacy and property rights of others.
• The drone shall never be modified or used for anything except its intended purpose.
• Before each use, an adult should review the product and battery to determine that no damage or hazards exist.
• DO NOT TOUCH SPINNING PROPELLERS.
• Do not allow anything to intentionally make contact in any way with spinning propellers o Prevent contact with
spinning blades by turning off remote prior to handling drone.
• Use caution and pay attention to your surroundings while operating drone.
• Do not fly drone into animals, people, or inanimate objects.
• Keep drone away from power lines, buildings, trees, public areas, and any other potentially hazardous areas.
• Do not operate in rain, heavy wind, and or any type of severe weather.
• Do not land drone on wet surfaces.
• Never touch or allow others to touch drone while it is flying.
• Always turn drone off when it is not in use.
• Always fly drone in large open areas.
• The drone will lose controlling capabilities if fly distance is more than maximum recommended altitude of 100 ft.
Keep below 100 ft. to avoid potential crashing risk.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Fly-aways are the responsibility of the individual
pilot and will not be replaced by the manufacturer.
WARNING: Changes or modifications to this unit not
expressly approved by the party responsible for
compliance could void the user’s authority to operate
the equipment.
TROUBLESHOOTING:
When remote switch is turned on, the remote light does not illuminate:
1) Check that batteries in the remote are installed correctly OR
2) Replace with new batteries.
When remote LED come dim or the control sensitivity is weak:
1) Remote batteries are low.
2) Replace them with new batteries.
Drone and remote properly pair, but the drone will not lift-off or the
drone LEDs flash during the flying:
1) Drone Li-Po needs charging.
2) Use charging cable to connect the drone to power source.
After trimming the drone, the drone flight is very unstable and
cannot fly properly:
1) One or more blades are most likely damaged.
2) Turn off the drone and remote.
3) Replace with the proper number replacement blade and try
flying again.
After impact, the drone is unstable:
1) Land the drone on the ground and propellers are stopped.
Press and hold Land button for 3s to calibrate the gyro.
2) If the above does not resolve the issue, reboot the drone and
controller and pair again.
Remote Controller and Drone can not be paired:
1) Check Point: Remote Controller must be close to Drone.
2) Do not exceed 4 meters.
Note: If there are 2 sets of Drones within 4 meters for Pairing, you
must pair one successfully before pairing the second set.
This drone weighs 0.242lbs (110g). As of December 21, 2015, the Federal
Aviation Administration (FAA) only requires registration on unmanned aircrafts
weighing more than .55 lbs. Visit www.faa.gov/uas/registration/ for more
information. Although the FAA does not require this drone to be registered,
ongoing compliance with federal, state, and local laws is an owner’s sole
responsibility. Always fly safely and respect the privacy of others.
Drone Air Racer