XV-Z12000 SERVICE MANUAL SERVICE-ANLEITUNG S14M8XV-Z1200 PROJECTOR PROJEKTOR MODEL MODELL XV-Z12000 In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used. Im lnteresse der Benutzersicherheit (erforderliche Sicherheitsregeln in einigen Ländern) muß das Gerät in seinen Originalzustand gebracht werden.
XV-Z12000 CONTENTS Page • • • • • • • • • • • • • Page SPECIFICATIONS ............................................. 3 INPOTANT SERVICE SAFETY NOTES ............ 4 OPERATION MANUAL ...................................... 9 REMOVING OF MAJOR PARTS ..................... 15 RESETTING THE TOTAL LAMP TIMER ......... 21 THE OPTICAL UNIT OUTLINE ........................ 22 ELECTRICAL ADJUSTMENT .......................... 26 TROUBLE SHOOTING TABLE ........................ 35 CHASSIS LAYOUT ........................
XV-Z12000 Specifications Product type Projector Model XV-Z12000 Video system NTSC 3.58/NTSC 4.43/PAL/PAL-M/PAL-N/PAL 60/SECAM DTV480I/DTV480P/DTV720P/DTV1080I Display method DLP chip, RGB optical shutter method DLP panel Panel size: 0.8" Display method: Single Panel Digital Micromirror Device (DMD™) by Texas Instruments Drive method: Digital Light Processing (DLP™) No. of dots: 921,600 dots (1,280 [H] X 720 [V]) Lens 1—1.35X zoom lens, F2.5—8, f = 32.5—44.
XV-Z12000 IMPORTANT SERVICE SAFETY NOTES (for USA) Ë Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and servicing guidelines as follows: » Use an AC voltmeter with sensitivity of 5000 ohm per volt., or higher, sensitivity to measure the AC voltage drop across the resistor (See Diagram). » All checks must be repeated with the AC plug connection reversed.
XV-Z12000 NOTE TO SERVICE PERSONNEL NOTE POUR LE PERSONNEL D’ENTRETIEN UV-RADIATION PRECAUTION PRECAUTION POUR LES RADIATIONS UV The light source, lamp, in the projector emits small amounts of UV-Radiation. La source de lumière, la lampe , dans le projecteur émet de petites quantités de radiation UV. AVOID DIRECT EYE AND SKIN EXPOSURE. EVITEZ TOUTE EXPOSITION DIRECTE DES YEUX ET DE LA PEAU.
XV-Z12000 UV-RADIATION PRECAUTION (Continued) PRECAUTION POUR LES RADIATIONS UV (Suite) Lamp Replacement Remplacement de la lampe Note: Remarque: Since the lamp reaches a very high temperature during units operation replacement of the lamp should be done at least one hour after the power has been turned off. (to allow the lamp to cool off.) Installing the new lamp, make sure not to touch the lamp (bulb) replace the lamp by holding its reflector 2. [Use original replacement only.
XV-Z12000 WARNING: High brightness light source, do not stare into the beam of light, or view directly. Be especially careful that children do not stare directly in to the beam of light. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO MOISTURE OR WET LOCATIONS. CAUTION The lighting flash with arrowhead within a triangle is intended to tell the user that parts inside the product are risk of electric shock to persons. RISK OF ELECTRIC SHOCK.
XV-Z12000 Precautions for using lead-free solder 1 Employing lead-free solder "Main, Key, R/C Receiver(Rear), R/C Receiver(Front), LED, IRIS DRIVE ,PC I/F and Power PWB" of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The alphabetical character following LF shows the type of lead-free solder. Example: LFa Indicates lead-free solder of tin, silver and copper.
XV-Z12000 Operation Manual rt Names Projector (Front and Top View) MENU bu tton Adjustment b uttons (", ', \, |) For displaying adjustment and setting screens. For selecting menu items. ENTER butto n RESIZE bu tton For switching the screen size (SIDE BAR, SMART STRETCH, etc.). For setting items selected or adjusted on the menu. UNDO button For undoing an operation or returning to the default settings. INPUT butto n For switching input mode 1, 2, 3, 4 or 5. ON bu tton For turning the power on.
XV-Z12000 INPUT 3 terminal Terminal for connecting video equipment with an S-video terminal. Projector (Rear View) INPUT 1 terminals RS-232C terminal Terminals for component and RGB signals. For controlling projector using a computer. INPUT 5 terminal DC 12V OUTPUT terminal Terminal for DVI digital, computer RGB and component signals. WIRED REMOTE cont ro l input terminal INPUT 2 terminals Terminals for component and RGB signals. INPUT 4 terminal For connecting video equipment.
XV-Z12000 Names Remote Control (Front View) STANDBY b utton For putting the projector into the standby mode. ON button For turning the power on. KEYSTONE button For adjusting Keystone Correction or Vertical Size setting. MENU button For displaying adjustment and setting screens. ENTER button For setting items selected or adjusted on the menu. Adjustment buttons (", ', \, |) For selecting menu items. UNDO button For undoing an operation or returning to the default settings.
XV-Z12000 ing the Remote Control Available Range of the Remote Control The remote control can be used to control the projector within the ranges shown in the illustration. Remote control Note 23'(7 m) • The signal from the remote control can be reflected off a screen for easy operation. However, the effective distance of the signal may differ due to the screen material. 45˚ 30˚ 30˚ When using the remote control: • Be sure not to drop, expose to moisture or high temperature.
XV-Z12000 Connection Pin Assignments nnecting Pin Assignments DVI-I (INPUT 5 / DIGITAL T INPUT) port: 29 pin connector • DVI Digital INPUT C3 C5 Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 24 23 • • • ~ • • • 18 17 C4 C2 C1 16 8 7• • • • • ~ • • • • • 2 1 ••••••••• ~ ••••••••• 9 • DVI Analog RGB Input Pin No.
XV-Z12000 Dimensions mensions Rear View Top View Side View 15 49/50 (406) Side View 7 (178) Front View 18 11/16 (475) Bottom View Unit: inches (mm) 14
XV-Z12000 REMOVING OF MAJOR PARTS 1. Removing the top panels 1-1. Remove the six lock screw. 1-2. Press on side Arrow A of the bottom body and Lift the rear body. 1-3. Disconnect the connector. 1-4. Press on front Arrow B of the bottom body and unhook the claws, and detach the top body. 2-1. Remove the two screws and detach the LED PWB. 2-2. Remove the one screw and detach the R/C PWB. 2-3. Remove the three screws and detach the operation PWB.
XV-Z12000 2. Removing the cooling fan and PWB unit assembly. 3-1. 3-2. 3-3. 3-4. Disconnect the ten connectors. Remove the two screws and detach the lamp socket. Remove the two screws and detach the cooling fan. Remove the four screws and detach the PWB unit assembly.
XV-Z12000 3. Removing the rear panel, PC unit, cooling duct and main PWB unit. 4-1. 4-2. 5-1. 5-2. 6-1. 7-1. 8-1. 8-2. 8-3. Remove the two screws. Remove the three screws and detach the rear panel. Remove the two screws. Remove the four hexagonal supports and detach the shield plate. Remove the four screws and detach the PC I/F unit. Remove the four screws and detach the cooling duct. Remove the two hexagonal supports. Remove the five screws and detach the main PWB unit. Remove the lock of the holder.
XV-Z12000 4. Removing the power unit shield , power/ballast unit and power unit. 9. Remove the seven screws and detach the power unit shield. 10-1. Remove the two screws. 10-2. Remove the four white supports and detach the ballast unit. 11. Remove the four screws and detach the power unit.
XV-Z12000 5. Removing the optical mechanism unit and R/C PWB unit. 12. 13. 14. 15. Disconnect the lens connectors from the IRIS DRIVER PWB unit. Remove the six screws and detach the optical mechanism unit. Remove the one screw and detach the R/C PWB unit. Remove the Two hooks and detach the IRIS DRIVER PWB unit.
XV-Z12000 6. Removing the lamp unit, CW fan, outlet fan, bimetal, wind way duct, shield plate and formater PWB. 16. Remove the three screws and detach the lamp unit. 17. Remove the two screws and detach the CW fan. 18. Remove the three screws and detach the outlet fan. 19-1. Remove the two screws and detach the bimetal. 19-2. Remove the two screws and detach wind way duct. 20-1. Remove the four screws and detach the shield plate(B). 20-2. Remove the three screws and detach the formater PWB. 20-3.
XV-Z12000 Resetting the TOTAL LAMP TIMER ● Resetting the lamp timer Reset the lamp timer after replacing the lamp. 1 Connect the power cord. 2 Reset the lamp timer. • Plug the power cord into the AC socket of the projector. • While holding down , " and | on the projector, press on the projector. • “LAMP 0000H” is displayed, indicating that the lamp timer is reset. Info • Make sure to reset the lamp timer only when replacing the lamp.
XV-Z12000 THE OPTICAL UNIT OUTLINE Layout for proper setup of the optical components and parts (top view) Projection lens Prism DMD Chips Condensor lens IR-cut mirror Light tunnel Relay lens Fold mirror Condensor lens Color filter Lamp Item 1 Lamp 2 Condensor lens, IR-cut mirror and light- tunnel 3 Color filter 4 Relay lens and fold mirror 5 Prism 6 DMD chip 7 Projection lens Descriptions The DC Light source lamp with parabola reflector.
XV-Z12000 Adjusting the mirrors Make adjustment by the indication territory on the screen to prevent the circumference of the screen from getting dark because a lighting range deviated. 1. Remove the top body so that the optical unit may be seen. Display white only screen on the screen. 2. Detach the mirror adjustment part cover 1 on the bottom right of the projection lens. 3.
XV-Z12000 Replacement of the DMD or formatter unit The DMD may be broken by static electricity. Always wear an earth band before beginning the work. The contact of the interposer is minute, so pay sufficient attention when handling. Attachment of DMD Check of DMD bin voltage Check the last alphabet of the lowest line of the rear side of the DMD to attach.
XV-Z12000 1 Formatter unit 2 DMD 3 Interposer 4 Clamp 5 Backer plate 6 Screw (4 pcs) 7 Radiator fin 8 Clip When the DMD unit has been replaced Note: DMD chip and Formatter PWB are supplied at the same time, and an exchange only with DMD isn't done.Refer to "REMOVING OF MAJOR PARTS" when exchanging Formatter PWB. There is no need to readjust the back focal distance of the projection lens. If focusing is noticeably poor, however, make this readjustment. (1) (2) (3) (4) (5) (6) (7) Provide a distance of 2.
XV-Z12000 No. Adjusting procedure ELECTRICAL ADJUSTMENT Adjusting point Adjusting conditions The unit has been adjusted optimally at the time of factory shipment. However, if the screen position is deviated or when exchanging parts, make an adjustment as shown below. • Turn on the power (lamp on state) and wait for 15 minutes for aging. • Enter the adjustment process mode with SW2002 (tact switch) on the main unit.
XV-Z12000 No. Adjusting point 2-2 A/D (COMP) G brightness adjustment CR offset checking CB offset checking 3 Color wheel index adjustment Adjusting conditions Adjusting procedure 1. Input a white pattern color difference signal of Y (brightness) 0% and CB/CR 0%. INPUT 5 2. Select the following group and subject. Group: A/D (COMP) Subject: G-BRIGHT CR OFFSET CB OFFSET 1. Select the A/D (COMP) menu and set G-BRIGHT to the numeric value of G-BRIGHT of A/D (RGB). 2.
XV-Z12000 No. Adjusting point Adjusting conditions Adjusting procedure 8 NTSC color saturation adjustment 1. Input split color bar signal. INPUT 4 2. Select the following group and subject. Group: VIDEO1 Subject: N-COLOR 1. Select the VIDEO 1 menu to check the value of NCOLOR. Fixed value: 100 9 PAL color saturation adjustment 1. Input the PAL color bar. INPUT 4 2. Select the following group and subject. Group: VIDEO1 Subject: P-COLOR 1. Select the VIDEO 1 menu to check the value of PCOLOR.
XV-Z12000 No. Adjusting point Adjusting conditions Adjusting procedure 15 Off-timer performance check 1. Set to the no-signal state. 2. Select the following group and subject. Group: LINE Subject: OFF 1. Select OFF of LINE in the process mode and press the ENTER key on the remote control. The 5-minute display of the off timer appears and check that the power is turned off about 6 seconds after the display appears. 16 Delivery settings 1. Select the following group and subject.
XV-Z12000 No. Adjusting point Adjusting Adjusting conditions the PC Board Adjusting procedure 1. Initializing the EEPROM 1) Press SW2002 to enter the process mode. 2) Execute the S1 command on the SSS menu. (The S1 command initializes the PC board alone. Do not execute the S2 command because otherwise the adjustment data other than the PC board will be initialized.) 2. Adjustment of input signal level 2.1 Setting the oscilloscope Set the oscilloscope range to DC 1V/div. and 5 É sec/div . 2.
XV-Z12000 No. Adjusting point Background Adjusting conditions adjustment method Adjusting procedure Ι. Adjustment conditions 1) Adjustment item: Process mode, DLP menu GAMMA R-GAIN, G-GAIN, B-GAIN 2) Input signal: Component video 75% white signal 1 With the component video 100% white signal, adjust the output to 0.7 ± 0.05 Vp-p (excluding the synchronous part.) (The sync signal is 0.3 Vp-p.) 2 Next drop the image signal output to 75%. 3 Input the signal to INPUT5 (DVI-I connector).
XV-Z12000 Process menu 1 No.
XV-Z12000 Process menu 2 No.
XV-Z12000 Process menu 3 No. Adjusting point Group Adjust CVIC Adjusting conditions CVIC Sub Group CMS-HUE CMS-SAT CMS-VAL DEGAMMA GAMMA POS Version Check etc.
XV-Z12000 TROUBLE SHOOTING TABLE Checking the basic performance Is the POWER LED on or flickering in red or blue? NO Go to "Checking the power unit" YES Is the set turned on by the set’s or remote controller’s power key? NO Go to "Checking the microcomputer peripherals" and "Checking the PC PWB". YES Is the cooling fan running? Is the lamp on? NO Go to "Checking the lamp light-up". YES NO Is the user menu displayed? Check the formatter circuit’s peripheral circuits.
XV-Z12000 Checking the power unit Are all the connectors NO inside the power unit tightly connected? Insert the connectors CN7106, 7103, 7101AND 7102 tightly. YES Is the lamp cover closed completely? NO Tighten up the lamp door closed with the screws. YES Is the bimetal switch off? NO Replace the bimetal switch or press the red button to reset. YES Is AC voltage applied across the RL7001 relay? NO YES Is AC voltage applied across L7005? Replace F7001. NO Replace F7002.
XV-Z12000 The lamp lights. The power lamp does not light at all. YES Check the power BU6V circuit. IC2005 is defective. YES Check the lamp door and the lamp switch. Try pressing the red button on the bimetal switch. Check the power outputs. NO When plugged into an AC socket, the power lamp turns red, but it goes out soon. NO The power lamp flashes slowly. YES Check the 3.3 V power supply. NO The lamp turns blue, but it goes out in about 15 seconds. (The stand-by indicator turns on.
XV-Z12000 The lamp is flashing blue continuously. Is a voltage of 2.5 V or more present at pins (5) and (15) of J8003 in the PCI/F unit? NO Check IC2005 (sub-microcomputer) and peripheral parts. YES Is a voltage of 3 V or more present at pin (8) of J8003 in the PCI/F unit? NO Is a 1 Vp-p clock signal present at pin (F2) of IC9101 in the formatter unit? YES NO Check IC2005 (sub-microcomputer) and peripheral parts. Check X9101.
XV-Z12000 No horizontal synchronization is being supplied from the external synchronization input. This is not normal. Is the terminal input connection as specified? Is YES the cable tightly connected? NO Is there the horizontal sync pulse at pin (14) of IC2506? NO Check the line between IC2506 and the input terminal. YES Is there the horizontal sync pulse at pin (11) of IC2509? Use the specified cable. Reconnect it tight enough. NO Check the line between IC2506 and IC2509.
XV-Z12000 Checking IC3504 (3D Noise Reduction) and its Peripheral Circuits Are there the input signals at pins (88) (Y signal) and (96) (C signal) of IC3504? NO Check the signal input circuit or IC2505 and its peripheral circuits. YES Are there the output signals at pins (84) (Y signal) and (83) (C signal) of IC3504? NO Check IC3504 and its peripheral circuits. YES Check the line up to the PC board connector or the circuits that follow the PC board.
XV-Z12000 Check the PCI/F unit. Can the menu display be brought up? YES NO Check OSD. Check the RGB input. Check the input at the components. Check the VIDEO input. Check the 480iRGB (or component) input. Check the basic flow of the signals. Since the component and VIDEO signals follow the same path to the output as the formatter unit uses, after CVIC (IC8025), the check that would otherwise be performed after the CVIC does not need to be performed. (480i and 576i are excluded.
XV-Z12000 Check OSD. Press the key on the main unit or the [MENU] key on the remote control. Is the menu display brought up? YES End. NO Is there a clock signal at R8974? NO Is a clock signal (37.125 MHz) present at TL8114? YES IC8029 (GA4) is defective. NO YES Is there a clock signal at FL8110? NO X8005 is defective. YES IC8025 (CVIC) is defective.
XV-Z12000 Check the RGB input. Select INPUT1 or INPUT2 using the operation key or the remote control. Select INPUT1 or INPUT2 using the operation key or the remote control. Is a projection image displayed? NO Go to "Check the video input.". YES Is the picture distorted? YES Go to "Check the synchronization signal.". NO Go to "Check the RGB signal.". NO Go to "IC8004 peripheral check". NO Are all three colors (R, G, and B) being output? YES Is the image frame normal? YES End.
XV-Z12000 Check the video input. Is the signal generator (input source) set correctly? NO Set the signal generator (input source) correctly. YES When checking the optional input signal on the menu display, select the RGB input or set it to RGB using the RGB/COMP key on the remote control (toggles). Check the input signal type. Is the video signal present at pin (25) of IC8367? NO Check the installation of the main unit. The main unit is defective. NO The IC8367 peripheral circuit is defective.
XV-Z12000 Check the synchronization signal. Is the signal generator (input source) set correctly? NO Set the signal generator (input source) correctly. YES Is a vertical synchronization signal present at TL8134? NO YES Is a horizontal synchronization signal present at TL8133? NO The main unit is defective.
XV-Z12000 Check the RGB signal. Is the input signal type set to RGB? No YES Set the input signal type to RGB. Go to "GA4 peripheral check". GA4 peripheral check Press the key on the main unit or the NO [MENU] key on the remote control. Is the menu display brought up? Go to "Check OSD.". YES Select the color bar from the process mode Pattern menu.
XV-Z12000 IC8004 peripheral check Set the signal generator to output a RAMP signal. NO The IC8325 peripheral parts or IC8025 (CVIC) are defective. NO The IC8004 clock oscillation circuit or IC8004 is defective. NO Check the RAMP signal on TL8073 - 75 using an oscilloscope.
XV-Z12000 Check the input at the components (480i and 580i are excluded). Supply a component signal to INPUT1 or INPUT2. Select INPUT1 or INPUT2 using the key on the main unit or the remote control. When checking the optional input signal on the menu display, select the component or set it to the component using the RGB/COMP key on the remote control (toggles). Check the input signal type. NO Go to "Check the SOG circuit.".
XV-Z12000 Check the SOG circuit. Is the signal generator (input source) set correctly? NO Set the signal generator (input source) correctly. YES Is a composite synchronization signal present at R8981? YES The SOG circuit is normal. NO Is a composite synchronization signal with the correct timing being output to TL8136? YES The IC8325 peripheral circuit is defective.
XV-Z12000 Check the 525i (625i) RGB (or component) input. Supply a 525i (625i) RGB (or component) signal to INPUT1 or INPUT2. Select INPUT1 or INPUT2 using the key on the main unit or the remote control. When checking the optional input signal on the menu display, select RGB (or component) or set it to RGB (or component) using the RGB/COMP key on the remote control. Check the input signal type. NO Go to "Check the SOG circuit.
XV-Z12000 Check the composite VIDEO (CVBS) input. Check the S-VIDEO input. Supply an NTSC3.58 VIDEO signal to INPUT4. Supply an NTSC3.58 S-VIDEO signal to INPUT3. Select INPUT4 using the key on the main unit or the remote control. Select INPUT3 using the key on the main unit or the remote control. Select NTSC3.58 as the optional video signal system on the menu display. Select the video signal type.
XV-Z12000 Check the VIDEO synchronization signal. Is a vertical synchronization signal present at TL8140? NO YES Is a horizontal synchronization signal present at TL8142? NO YES The VIDEO synchronization signal is normal. Is a clock signal (20.25 MHz) present at TL8002? NO X8006 or IC8338 is defective. YES NO Is the input signal 525iRGB (or component)? YES NO Is a video signal present at TL8138? Is a video signal present at pin (74) of IC8338? YES IC8338 is defective.
XV-Z12000 IC8338 peripheral check Is a clock signal (20.25 MHz) present at TL8002? NO Check X8006, or IC8338 is defective. YES Is a clock signal present at TL8004? NO IC8338 is defective. YES Supply a RAMP signal to INPUT4, and observe pins (31 - 40) of IC8338 using an oscilloscope. Is a pulse present at pins (31 - 40) of IC8338? NO IC8338 is defective. YES Supply a color bar signal to INPUT4, and observe pins (41 - 50) of IC8338.
XV-Z12000 Check the DVI analog input. Supply a PC-RGB analog signal to INPUT5. Select INPUT5 using the key on the main unit or the remote control. When checking the optional input signal on the menu display, set it to "A. RGB". Check the input signal type. YES Is a projection image displayed? End. NO Is an RGB signal present at pins (126), (136), and (141) of IC8004? YES Check in the vicinity of the DVI connector.
XV-Z12000 Check the DVI digital input. Supply a PC-RGB digital signal to INPUT5. Select INPUT5 using the key on the main unit or the remote control. When checking the optional input signal on the menu display, set it to "D. PC RGB". Check the input signal type. YES Is a projection image displayed? End. NO Is a clock signal present at R8685? NO Check the DVI connector peripherals. IC8298 is defective. YES Is a pulse present at pins (10 - 37) and (48 - 77) of IC8298? NO IC8298 is defective.
XV-Z12000 Technische Daten Produkttyp Modell Videosystem Wiedergabeverfahren DLP-Panel Objektiv Projektionslampe S-Videoeingangssignal Komponenten-Eingangssignale Horizontale Auflösung RGB-Eingangssignal Videoeingangssignal Computer-Steuerungssignal Pixeltakt Vertikale Frequenz Horizontale Frequenz Nennspannung Eingangsspannung Nennfrequenz Leistungsaufnahme (normal) Leistungsaufnahme (Bereitschaft) Wärmeableitung Betriebstemperatur Lagertemperatur Gehäuse I/R-Trägerfrequenz Abmessungen (ca.
XV-Z12000 HINWEIS FÜR DAS WARTUNGSPERSONAL Auswechseln der Lampe ACHTUNG: UV-STRAHLUNG Hinweis: Die Beleuchtungsquelle des LCD-Projektors, eine UHP-Lampe, emittiert eine geringe Menge UV-Strahlung. DIREKTE BESTRAHLUNG AUF AUGEN UND HAUT MUSS VERMIEDEN WERDEN. Zur Gewährleistung der Sicherheit muß folgendes beachtet werden: 1. Bei Arbeiten am Projektor bei eingeschalteter Lampe und abgenommenem oberen Gehäuse muß unbedingt eine Sonnenbrille getragen werden.
XV-Z12000 Vorsichtsmaßregeln für bleifreien Lötzinn 1 Verwendung von bleifreiem Lötzinn Die "Haupt-, Taste-, Einlass (Hinter)-, Einlass (Vorter)-, LED-, Blendentreiber-, PC-I/F-, Netz-Platine" dieses Modells verwendet bleifreien Lötzinn. Das LF-Symbol zeigt bleifreien Lötzinn an und ist an den Platinen und Wartungsanleitungen angebracht. Der Buchstabe nach LF zeigt den Typ des bleifreien Lötzinns an. Beispiel: LFa Zeigt bleifreien Lötzinn aus Zinn, Silber und Kupfer an.
XV-Z12000 Bedienungsanleitung Bedienelemente Projektor (Vorde-und Draufsicht) MENU-Taste Einstelltasten (", ', \, |) Für die Anzeige des Justierungs- und Einstellungsbildschirms. Für die Wahl der Menüpunkte. ENTER-Taste RESIZE-Taste Für die Einstellung der gewählten oder eingestellten Menüpunkte. Für das Umschalten der Bildwandgröße (SEITENBA., SMART STRECKEN, usw.) UNDO-Taste Für das Rückgängigmachen eines Bedienschrittes oder für die Rückkehr zu den Grundeinstellungen.
XV-Z12000 INPUT 3-Anschluss Anschluss für ein Videogerät mit einem SVIDEO-Anschluss. Projektor (Hintersicht) INPUT1-Anschlüsse Anschlüsse für Komponenten- und RGBSignale. RS-232C-Anschluss INPUT 5-Anschluss DC 12 V OUTPUTAnschluss Für die Bedienung des Projektors über Computers. Anschluss für DVI-Digital-, Computer-RGB- und COMPONENT-Signale. WIRED REMOTEEingabeanschluss INPUT 2-Anschluss Anschlüsse für Komponenten- und RGB-Signale. INPUT 4-Anschluss Für den Anschluss eines Videogerätes.
XV-Z12000 Bedienelemente Fernbedienung (Vordersicht) STANDBY-Taste Schaltet den Projektor in den Standby-Modus. ON-Taste Schaltet die Stromversorgung ein. KEYSTONE-Taste Für die Trapezkorrektur oder die Einstellung der vertikalen Größe. MENU-Taste Für die Anzeige des Justierungs- und Einstellungsbildschirms. ENTER-Taste Für die Einstellung der gewählten oder eingestellten Menüpunkte. Einstelltasten (", ', \, |) Für die Wahl der Menüpunkte.
XV-Z12000 Verwendung der Fernbedienung Reichweite der Fernbedienung Fernbedienung Der Projektor kann mittels der Fernbedienung innerhalb der in der Abbildung gezeigten Bereiche gesteuert werden. 7m 30˚ Hinweis 45˚ • Das Signal von der Fernbedienung kann für eine einfache Bedienung von der Bildwand reflektiert werden. Die tatsächliche Reichweite des Signals kann je nach Bildwandmaterial unterschiedlich sein.
XV-Z12000 Pin-Belegung Verbindungs-Pin-Zuweisungen DVI-I (INPUT 5 / DIGITAL INPUT)-Anschluss: 29-pol. Stecker • DVI-Digital-Eingang C3 C5 Pin Nr. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 24 23 • • • ~ • • • 18 17 C4 C2 C1 16 8 7• • • • • ~ • • • • • 2 1 ••••••••• ~ ••••••••• 9 • DVI-Analog-RGB-Eingang Pin Nr. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Signal Pin Nr.
XV-Z12000 Abmessungen Abmessungen Einheiten: mm Ansicht von der Seite Ansicht von oben 406 Ansicht von der Seite Ansicht von hinten 178 Ansicht von vorne 475 Ansicht von unten Einheit:mm 64
XV-Z12000 ENTFERNEN DER HAUPTTEILE 1. Ausbau der oberen Abdeckung 2-1. Die beiden Schrauben losdrehen, dann die LEDPlatine entfernen. 2-2. Die Schraube losdrehen und die R/C-Platine entfernen. 2-3. Die drei Schrauben losdrehen und die Betriebsplatine entfernen. 1-1. Die sechs Sicherungsschrauben losdrehen. 1-2. An den seitlichen Pfeil A an der Gehäuseunterseite hineindrücken und die hintere Abdeckung anheben. 1-3. Den Stecker abziehen. 1-4.
XV-Z12000 2. Ausbau des Kühlgebläses und der Platineneinheit 3-1. 3-2. 3-3. 3-4. Die zehn Steckverbinder abziehen. Die beiden Schrauben losdrehen und die Lampenfassung entfernen. Die beiden Schrauben losdrehen und das Kühlgebläse entfernen. Die vier Schrauben losdrehen und die Platineneinheit entfernen.
XV-Z12000 3. Ausbau der Rückwand, der PC-Einheit, des Kühlschachts und der Hauptplatineneinheit 4-1. 4-2. 5-1. 5-2. 6-1. 7-1. 8-1. 8-2. 8-3. Die beiden Schrauben losdrehen. Die drei Schrauben losdrehen und die Abdeckplatte entfernen. Die beiden Schrauben losdrehen. Die vier Sechskanthalterungen entfernen, dann die Abdeckplatte entfernen. Die vier Schrauben losdrehen, dann die PC I/F-Einheit abnehmen. Die vier Schrauben losdrehen, dann den Kühlschacht abnehmen. Die beiden Sechskanthalterungen entfernen.
XV-Z12000 4. Entfernen der Netzteilabdeckung, der Netz-/Vorschaltgeräte-Einheit sowie des Netzteils. 9. Die sieben Schrauben losdrehen und die Netzteilabdeckung entfernen. 10-1. Die beiden Schrauben losdrehen. 10-2. Die vier weißen Halter entfernen, dann das Netzteil abnehmen. 11. Die vier Schrauben losdrehen, dann das Netzteil entfernen.
XV-Z12000 5. Ausbau der Optikmechanismus-Einheit und der R/C-Platineneinheit 12. 13. 14. 15. Die Linsenanschlüsse aus der Blendentreiber-Platineneinheit trennen. Die sechs Schrauben losdrehen und die Optikmechanismus-Einheit entfernen. Die Schraube losdrehen und die R/C-Platineneinheit entfernen. Die beiden Steckverbinder losdrehen und die Blendentreiber-Platineneinheit entfernen.
XV-Z12000 6. Ausbau von Lampeneinheit, Farbeinstellscheiben-Gebläse, Auslaßgebläse, Luftkanal, Abschirmblech und Bildformatiererplatine 16. Die drei Schrauben losdrehen und die Lampeneinheit entfernen. 17. Die beiden Schrauben losdrehen und das Farbeinstellscheiben-Gebläse entfernen. 18. Die drei Schrauben losdrehen und das Auslaßgebläse entfernen. 19-1. Die beiden Schrauben losdrehen und das Bimetall entfernen. 19-2. Die beiden Schrauben losdrehen und den Luftkanal entfernen. 20-1.
XV-Z12000 Rückstellen des Lampenbetriebszeit-Timers » Rückstellung des Lampen-Timers Den Lampen-Timer nach dem Lampenaustausch zurückzustellen. 1 Das Netzkabel anschließen. • Das Netzkabel am Netzanschluss des Projektors anschließen. 2 Den Lampen-Timer zurückstellen. • Während , " und | auf dem Projektor auf dem gleichzeitig gedrückt wird, Projektor drücken. • "LAMPE 0000H" erscheint und zeigt damit an, dass der Lampen-Timer zurückgestellt ist.
XV-Z12000 Beschreibung der Optik-Einheit Anordnung der optischen Komponenten und zugehörigen Bauteile (Draufsicht) Projektionsobjektiv Prisma DMD-Chips Kondensatorlinse IR-Arretierspiegel Lichtschacht Übertragungslinse Faltspiegel Kondensatorlinse Farbfilter Lampe Gegenstand 1 Lampe 2 Kondensatorlinse, IR-Arretierspiegel und Lichtschacht 3 Farbfilter 4 Übertragungslinse und Faltspiegel 5 Prisma 6 DMD-Chips 7 Projektionsobjektiv Beschreibung Gleichstrom-Lampe mit Parabolreflektor Die Kondensatorlin
XV-Z12000 Einstellung der Spiegel Einstellung des Anzeigebereichs am Bildschirm vornehmen, um Dunkelbereiche am äußeren Bildschirmrand zu vermeiden. 1. Die obere Abdeckung abnehmen, so daß die Optikeinheit sichtbar wird. Nur Weiß am Bildschirm anzeigen. 2. Die Abdeckung 1 der Spiegeleinstellplatte an der Unterseite rechts vom Projektionsobjektiv entfernen. 3.
XV-Z12000 Austausch von DMD oder Formatter-Einheit DMD kann durch statische Elektrizität beschädigt werden. Bei der Arbeit ist ein Erdstreifen stets zu tragen. Da der Kontakt des Interposers sehr klein ist, diesen sorgfältig behandeln. Montage von DMD Überprüfung der binären DMD-Spannung Das letzte Alphabet in der niedrigsten Zeile auf der Rückseite von DMD überprüfen, das montiert werden soll.
XV-Z12000 Wenn die DMD-Einheit ausgewechselt wurde Hinweis: Der DMD-Chip und die Bildformatiererplatine werden zur gleichen Zeit geliefert. Es wird ausschließlich der DMD-Chip ausgewechselt. Beziehen Sie sich beim Auswechseln der Bildformatiererplatine bitte auf den Abschnitt "AUSBAU DER WICHTIGSTEN BAUTEILE". Die hintere Brennweite des Projektionsobjektivs braucht nicht eingestellt zu werden. Wenn die Brennpunkteinstellung jedoch unzufriedenstellend ist, muß die folgende Einstellung ausgeführt werden.
XV-Z12000 ELEKTRISCHE EINSTELLUNGEN Beim Versand vom Werk ist das Gerät optimal eingestellt. Wenn der Bildschirm von dem richtigen Position abweicht, oder nachdem Teile ausgewechselt worden sind, ist das Gerät folgendermaßen einzustellen. • Die Stromversorgung einschalten (Lampe leuchtet auf), und das Gerät für 15 Minuten altern. • SW2002 (Taktschalter) auf dem Hauptgerät drücken, um in den Einstellprozeßmodus umzuschalten.
XV-Z12000 Nr. Einstellgegenstand 2-2 A/D (COMP) Einstellung der G- Helligkeit Überprüfung des CR-Offsets Überprüfung des CB-Offsets 3 Einstellung des FarbeinstellscheibenIndexes Einstellbedingungen Einstellverfahren 1. E i n W e i ß m u s t e r Farbdifferenzsignal mit 0 % Y (Helligkeit) und 0 % CB/ CR eingeben. INPUT5 2. Die nachfolgende Gruppe bzw. die Positionen wählen: Gruppe: A/D (COMP) Position: G-BRIGHT CR OFFSET CB OFFSET 1.
XV-Z12000 Nr. Einstellgegenstand Einstellbedingungen Einstellverfahren 8 Einstellung der NTSCFarbsättigung 1. Geteiltes Farbbalkensignal an INPUT 4 eingeben. 2. Die nachfolgende Gruppe bzw. die Positionen wählen: Gruppe: VIDEO1 Position: N-COLOR 1. Das Menü VIDEO1 wählen, um den Wert von NCOLOR zu überprüfen. Fixierte Einstellung: 100 9 Einstellung der PALFarbsättigung 1. Das PAL-Farbbalkensignal zuführen. INPUT4 2. Die nachfolgende Gruppe bzw.
XV-Z12000 Nr. Einstellgegenstand Einstellbedingungen Einstellverfahren 14 Überprüfung der RGBLeistungswerte 1. Das RGB-Signal zuführen. INPUT5 2. Die nachfolgende Gruppe bzw. die Positionen wählen: Gruppe: LINE Position: L4 1. L4 aus dem Prozeßmodus LINE wählen, und die ENTER-Taste auf der Fernbedienung drücken. Die Leistung von Bild, Helligkeit, Takt, Phase, Horizontal- und Vertikalposition überprüfen. überprüfen. 15 Leistung des AusschaltTimers 1. Den Kein-Signal-Status herstellen. 2.
XV-Z12000 Einstellung der PC-Platine 1. Initialisierung des EEPROM 1) Den Schalter SW2002 drücken, um den Prozeßmodus aufzurufen. 2) Den S1-Befehl am SSS-Menü ausführen. (Der S1-Befehl dient dazu, die Platine alleine zu initialisieren. Der S2-Befehl darf allerdings nicht eingegeben werden, da hierdurch auch alle anderen Einstelldaten der Platine initialisiert werden.) 2. Einstellung des Eingangssignalpegels 2.1 Vorbereiten des Oszilloskops Das Oszilloskop auf einen Bereich zwischen 1 V/div. und 5 µs/div.
XV-Z12000 Verfahren der Farbhelligkeitseinstellung Einstellung in den folgenden beiden Schritten I Einstellbedingungen 1. Einstellgegenstand: Prozeßmodus, Menü DLP GAMMA R-GAIN, G-GAIN, B-GAIN 2. Eingangssignal: Komponenten-Video-75%-Weißsignal 1 Mit dem Komponenten-Video-100%-Weißsignal den Ausgang auf 0,7 ± 0,05 Vp-p (ausschließlich dem Synchronteil). (Das Synchronsignal ist 0,3 Vp-p.) 2 Den Bildsignalausgang auf 75% reduzieren. 3 Das Signal in INPUT5 (DVI-I-Anschluß) eingeben. 3.
XV-Z12000 Prozeßmenü 1 Gruppe Adjust PC Image Untergruppe A/D (RGB) Gegenstand R-BRIGHT G-BRIGHT B-BRIGHT R-D B-D G-D AD-AUTO G-BRIGHT CB-OFFSET CR-OFFSET AD AUTO CW-INDEX DLP-GAMMA R-BRIGHT G-BRIGHT B-BRIGHT R-GAIN G-GAIN B-GAIN NTSC-H PICTURE BRIGHT TINT N-COLOR P-COLOR S-COLOR SET UP SET UP B SET UP C VIDEO-AUTO PEAK FIL PEAK GAIN PEAK COR N358 DLY N433 DLY PAL DLY SECAM DLY L1 L2 L3 L4 OFF TEMP OFF SENSOR CHECK A/D (COMP) Adjust HDDE formatter DLP Adjust VIDEO Image VIDEO1 VIDEO2 Process mode
XV-Z12000 Prozeßmenü 2 Gruppe INITIAL SETTING Sample Pattern Adjust CVIC Untergruppe Gegenstand TIME S1 S2 S3 S4 S5 LAMP RGB RGB(50) CROSS STEP COLOR CHR SSS PATTERN CVIC PROGRESSSIVE MODE IP MDSW PTGSW C-TESTSW C-ILG-LY C-MODE-LY C-VE-LY TABLE ENH-PLUS ENH-GAIN CUBIC TABLE ENH-PLUS ENH-GAIN CUBIC YNR-LEBEL YNR-K YNR-FSEL YNR-FILSW CNR-LEBEL CNR-K CNR-FSEL CNR-FILSW TBL-ON TESTSW ENABLE MV-F VDDYP ENH-MODE(V) ENH-MODE(PC) NR PTG 83
XV-Z12000 Prozeßmenü 3 Gruppe Adjust CVIC CVIC Untergruppe CMS-HUE Gegenstand TABLE CMS-HUE-R CMS-HUE-Y CMS-HUE-G CMS-HUE-C CMS-HUE-B CMS-HUE-M TABLE CMS-SAT-R CMS-SAT-Y CMS-SAT-G CMS-SAT-C CMS-SAT-B CMS-SAT-M TABLE CMS-VAL-R CMS-VAL-Y CMS-VAL-G CMS-VAL-C CMS-VAL-B CMS-VAL-M TABLE R GAMMA G GAMMA B GAMMA R GAIN G GAIN B GAIN R OFFSET G OFFSET B OFFSET IPL E2PROM ADR RD/WR CMS-SAT CMS-VAL DEGAMMA GAMMA POS Version Check etc.
XV-Z12000 FEHLERSUCHTABELLE Überprüfung der allgemeinen Leistung Blinkt die POWER-LED rot oder blau? NEIN Zur "Überprüfung des Netzgeräts" weitergehen. JA Wird das Gerät durch die Netztaste auf der Fernbedienung eingeschaltet? NEIN JA Läuft das Kühlgebläse? Leuchtet die Lampe? NEIN Zur "Überprüfung der Lampenfunktion" weitergehen. JA Wird das Benutzermenü angezeigt? NEIN Den Bildformatierer-schaltkreis und seine peripheren Schaltkreise überprüfen.
XV-Z12000 Überprüfung der Stromversorgung Sind alle Steckverbindungen innerhalb der Stromversorgung fest angeschlossen? NEIN Die Steckverbinder CN7106, 7103, 7101 und 7102 gut einstecken. JA Ist die Lampenabdeckung vollkommen geschlossen? NEIN JA NEIN Funktioniert der Bimetallschalter? Den Bimetallschalter auswechseln oder den roten Knopf zwecks Rückstellung drücken. JA Wird dem Relais RL7001 Netzspannung zugeführt? NEIN JA Wird dem L7005 Netzspannung zugeführt? F7001 auswechseln.
XV-Z12000 Die Lampe leuchtet. Die Netzanzeige leuchtet nicht. JA Den Spannungs-BU6V-Kreis Überprüfen. IC2005 ist defekt. JA Die Lampenklappe und den Lampenschalter überprüfen. Die rote Taste am Bimetallschalter drücken. Jeden Ausgang der Stromversorgung überprüfen. NEIN Beim Anschluß an eine Steck-dose leuchtet die Netzanzeige rot, aber sie erlischt bald. NEIN Die Netzanzeige blinkt langsam. JA Die 3,3-V-Spannungsversorgung überprüfen.
XV-Z12000 Die Lampenanzeige blinkt blau weiter. Liegt eine Spannung von 2,5 V oder darüber an den Stiften (5) und (15) von J8003 in der PCI/F-Einheit an? NEIN IC2005 (Sub-Mikrocomputer) und seine Peripherie überprüfen. JA Liegt eine Spannung von 3 V oder darüber am Stift (8) von J8003 in der PCI/F-Einheit an? JA IC2005 (Sub-Mikrocomputer) und seine Peripherie überprüfen. NEIN Liegt ein Taktsignal von 1 Vss oder darüber am Stift (F2) von IC9101 in der Formatter-Einheit an? NEIN X9101 überprüfen.
XV-Z12000 Beim externen Synchronisierungseingang wird keine horizontale Synchronisation hergestellt. Dies ist nicht normal. Ist der TerminalEingangsanschluß wie spezifiziert? Ist das Kabel fest angeschlossen? NEIN JA Liegt am Stift (14) des IC2506 ein HorizontalSynchronsignal an? NEIN Das vorgeschriebene Kabel benutzen, einstecken und gut befestigen. Die Leitung zwischen dem IC2506 und dem Eingangsterminal überprüfen.
XV-Z12000 Überprüfung des IC3504 (3DRauschunterdrückung) und seiner peripheren Schaltkreise. Liegen Eingangssignale an den Stiften (88) (YSignal) und (96) (C-Signal) von IC3504 an? NEIN Den Eingangssignal schaltkreis des IC2505 und seine peripheren Schaltkreise überprüfen. JA Liegen Ausgangssignale an den Stiften (84) (YNEIN Signal) und (83) (C-Signal) von IC3504 an? JA Der IC3504 und sein peripherer Schaltkreis ist defekt. Die Leitung zum PC-Kartenanschluß bzw.
XV-Z12000 Überprüfen der PCI/F-Einheit Wird die Menüanzeige angezeigt? JA NEIN OSD überprüfen. Den RGB-Eingang überprüfen. Den Komponenteneingang überprüfen.. Den VIDEO-Eingang überprüfen. Den 480iRGB (oder Komponenten)-Eingang überprüfen. Den grundlegenden Signalfluß überprüfen. Was den Ausgang von CVIC (IC8025) bis zur Formatter-Einheit betrifft, folgen sowohl das Komponenten- als auch das VIDEOSignal dem gleichen Pfad.
XV-Z12000 OSD überprüfen. Die Taste auf der Hauptgerät oder die Taste [MENU] auf der Fernbedienung drücken. Erscheint der MenüBildschirm? JA Ende. NEIN Liegt ein Taktsignal an R897 an? NEIN JA Liegt ein Taktsignal (37,125 MHz) an TL8114 an? JA IC8029 (GA4) ist defekt. NEIN Liegt ein Taktsignal an FL8110 an? NEIN X8005 ist defekt. JA IC8025 (CVIC) ist defekt. Liegt ein Synchronsignal an TL8026-28 an? NEIN NEIN Liegt ein Synchronsignal an TL8112 und TL8113 an? JA JA IC8029 (GA4) ist defekt.
XV-Z12000 Den RGB-Eingang überprüfen. INPUT1 oder INPUT2 ein Synchrontrennungs-RGB-Signal zuführen. (525i und 625i werden ausgeschlossen.) Mit der Bedienungstaste bzw. Fernbedienung INPUT1 oder INPUT2 wählen. Wird ein Projektionsbild angezeigt? NEIN Mit dem Abschnitt "Überprüfen des Bildeingangs" fortfahren. JA Mit dem Abschnitt "Überprüfen des Synchronsignals" fortfahren. NEIN Mit dem Abschnitt "Überprüfen des RGB-Signals" fortfahren.
XV-Z12000 Überprüfen des Bildeingangs Ist der Signalgeber (Eingangsquelle) richtig eingestellt? NEIN Den Signalgeber (Eingangsquelle) richtig einstellen. JA Aus der Option in der Menüanzeige den RGB-Eingang als Eingangssignal wählen, oder mit der RGB/COMP-Taste (Umschalter) auf der Fernbedienung auf RGB stellen. Den Eingangssignaltyp überprüfen. Liegt ein Bildsignal am Stift (25) von IC8367 an? NEIN Die Montage am Hauptgerät überprüfen. Das Hauptgerät ist defekt.
XV-Z12000 Überprüfen des Synchronsignals Ist der Signalgeber (Eingangsquelle) richtig eingestellt? NEIN Den Signalgeber (Eingangsquelle) richtig einstellen. JA Liegt ein vertikales Synchronsignal an TL8134 an? NEIN JA Liegt ein horizontales Synchronsignal an TL8133 an? NEIN Das Hauptgerät ist defekt. JA Liegt ein vertikales Synchronsignal an TL8131 an? NEIN JA Liegt ein horizontales Synchronsignal an TL8130 an? NEIN IC8302, IC8325 oder die Peripherie von IC8001 ist defekt.
XV-Z12000 Überprüfen des RGB-Signals Wird der Eingangssignaltyp auf RGB gestellt? JA NEIN Den Eingangssignaltyp auf RGB stellen. Mit dem Abschnitt "Überprüfen der Peripherie von GA4" fortfahren.
XV-Z12000 Überprüfen der Peripherie von GA4 Die Taste auf der Hauptgerät oder die NEIN Taste [MENU] auf der Fernbedienung drücken. Erscheint der MenüBildschirm? Mit dem Abschnitt "Überprüfen von OSD" fortfahren. JA Den Farbbalken aus dem Prozeß- JA modus-Pattern-Menü wählen. Wird das Projektionsbild richtig angezeigt? "Überprüfen der Peripherie von GA4" ist beendet. NEIN Befindet sich der CW-INDEX-Wert NEIN des Prozeßmodus-DLP-Menüs im Bereich von 130 ± 2? CW-INDEX einstellen.
XV-Z12000 Überprüfen der Peripherie von IC8004 Den Signalgeber auf das RAMPSignal stellen. Liegt ein Synchronsignal an TL8022, TL8025 und TL8084 an? NO Die Peripherie von IC8325 oder IC8025 (CVIC) ist defekt. NO Der Taktschwingkreis von IC8004 oder IC8004 ist defekt. NO Liegt ein Bildsignal an den Stiften (124), (133) und (139) von IC8004 an? YES Liegt ein Taktsignal an R8128 an? YES Das RAMP-Signal von TL8073-75 mit einem Oszilloskop überprüfen.
XV-Z12000 Den Komponenteneingang (ausschließlich 480i und 580i) überprüfen. INPUT1 oder INPUT2 das Komponetensignal zuführen. Mit der Taste auf dem Hauptgerät bzw. auf der Fernbedienung INPUT1 oder INPUT2 wählen. Aus der Option in der Menüanzeige die Komponente als Eingangssignal wählen, oder mit der RGB/COMP-Taste (Umschalter) auf der Fernbedienung auf RGB stellen. Den Eingangssignaltyp überprüfen. Wird ein Projektionsbild angezeigt? NEIN Mit dem Abschnitt "Überprüfen der SOG-Schaltung" fortfahren.
XV-Z12000 Überprüfen der SOG-Schaltung Ist der Signalgeber (Eingangsquelle) richtig eingestellt? NEIN Den Signalgeber (Eingangsquelle) richtig einstellen. JA Liegt das Composite-Synchronsignal an R8981 an? JA Die SOG-Schaltung ist normal. NEIN Wird ein Composite-Synchronsignal mit dem korrekten Timing TL8136 zugeführt? JA Die Peripherieschaltung von IC8325 ist defekt.
XV-Z12000 Überprüfen des 525i (625i) RGB (oder Komponenten)-Eingangs INPUT1 oder INPUT2 das 525i (625i) RGB (oder Komponenten)Signal zuführen. Mit der Taste auf dem Hauptgerät bzw. auf der Fernbedienung INPUT1 oder INPUT2 wählen. Aus der Option in der Menüanzeige den RGB (oder Komponente) als Eingangssignal wählen, oder mit der RGB/COMP-Taste auf der Fernbedienung auf RGB (oder Komponente) stellen. Den Eingangssignaltyp überprüfen.
XV-Z12000 Überprüfen des S-VIDEOEingangs Überprüfen des CompositeVIDEO(CVBS)-Eingangs INPUT4 das VIDEO-Signal von NTSC3.58 zuführen. INPUT3 das S-VIDEO-Signal von NTSC3.58 zuführen. Mit der Taste auf dem Hauptgerät bzw. auf der Fernbedienung INPUT4 wählen. Mit der Taste auf dem Hauptgerät bzw. auf der Fernbedienung INPUT3 wählen. Aus der Option in der Menüanzeige NTSC3.58 als Videosignalsystem wählen. Den Videosignalsystem überprüfen.
XV-Z12000 Überprüfen des VIDEOSynchronsignals Liegt ein vertikales Synchronsignal an TL8140 an? NEIN JA Liegt ein horizontales Synchronsignal an TL8142 an? NEIN JA Das VIDEO-Synchronsignal ist normal. Liegt ein Taktsignal (20,25 MHz) an TL8002 an? NEIN X8006 oder IC8338 ist defekt. JA Entspricht das Eingangssignal 525iRGB (oder Komponente)? NEIN Liegt ein Bildsignal an TL8138 an? JA Liegt ein Bildsignal am Stift (74) von IC8338 an? NEIN JA IC8338 ist defekt.
XV-Z12000 Überprüfen der Peripherie von IC8338 Liegt ein Taktsignal (20,25 MHz) an TL8002 an? NEIN X8006 überprüfen. IC8338 ist defekt. JA Liegt ein Taktsignal an TL8004 an? NEIN IC8338 ist defekt. JA INPUT4 das RAMP-Signal zuführen, und die Stifte (31-40) von IC8338 mit einem Oszilloskop beobachten. Liegt ein Impuls an den Stiften (31-40) von IC8338 an? NEIN IC8338 ist defekt. JA INPUT4 das Farbbalkensignal zuführen, und die Stifte (41-50) von IC8338 mit einem Oszilloskop beobachten.
XV-Z12000 Überprüfen des DVI-Analogeingangs INPUT5 das PC-RGB-Analogsignal zuführen. Mit der Taste auf dem Hauptgerät bzw. auf der Fernbedienung INPUT5 wählen. Aus der Option in der Menüanzeige "A. RGB" als Eingangssignal wählen. Den Eingangssignaltyp überprüfen. Wird ein Projektionsbild angezeigt? JA Ende. NEIN Liegt ein RGB-Signal an den Stiften (126), (136) und (141) von IC8004 an? JA Die Peripherie des DVIAnschlusses überprüfen.
XV-Z12000 Überprüfen des DVI-Digitaleingangs INPUT5 das PC-RGBDigitalsignal zuführen. Mit der Taste auf dem Hauptgerät bzw. auf der Fernbedienung INPUT5 wählen. Aus der Option in der Menüanzeige "D. PC RGB" als Eingangssignal wählen. Den Eingangssignaltyp überprüfen. Wird ein Projektionsbild angezeigt? JA Ende. NEIN Ist das Taktsignal an R8685 vorhanden? NEIN JA Liegt ein Impuls an den Stiften (10-37) und (48-77) von IC8298 an? Die Peripherie des DVIAnschlusses überprüfen. IC8298 ist defekt.
XV-Z12000 -MEMO- 107
XV-Z12000 CHASSIS LAYOUT / CHASSIS-ANORDNUNG H G IRIS DRIVE DUNTKC176DE01 P2101 P2104 P2103 F E D C B A 1 2 3 4 5 6 108 7 8 9 10
XV-Z12000 10 11 12 13 14 15 109 16 17 18 19
XV-Z12000 BLOCK DIAGRAM / BLOCKSCHALTBILD H G F E D C B A 1 2 3 4 5 6 110 7 8 9 10
XV-Z12000 10 11 12 13 14 15 111 16 17 18 19
XV-Z12000 OVERALL WIRING DIAGRAM / GESAMTSCHALTPLAN H G F E D C B A 1 2 3 4 5 6 112 7 8 9 10
XV-Z12000 10 11 12 13 14 15 113 16 17 18 19
XV-Z12000 DESCRIPTION OF SCHEMATIC DIAGRAM BESCHREIBUNG DES SCHEMATISCHEN SCHALTPLANS VOLTAGE MEASUREMENT CONDITION: SPANNUNGSMESSUNGEN: 1. Voltages at test points are measured at the supply voltage of AC 220V. Signals are fed by a color bar signal generator for servicing purpose and the above voltages are measured with a 20k ohm/V tester. 1.
XV-Z12000 WAVEFORMS / WELLENFORMEN 1 P3580 32 (VIDEO AC) H : 20µ sec/div V : 500mV/div 2 P3580 34 (Y-signal) H : 10µ sec/div V : 0.2V/div 3 P3580 4 (CHROMA signal) H : 10µ sec/div V : 0.
XV-Z12000 Ë MAIN UNIT / HAUPT-EINHEIT -1/5 H G F E D C B A 1 2 3 4 5 6 116 7 8 9 10
XV-Z12000 10 11 12 13 14 15 117 16 17 18 19
XV-Z12000 Ë MAIN UNIT / HAUPT-EINHEIT -2/5 H G F E D C B A 1 2 3 4 5 6 118 7 8 9 10
XV-Z12000 10 11 12 13 14 15 119 16 17 18 19
XV-Z12000 Ë MAIN UNIT / HAUPT-EINHEIT -3/5 H G F E D C B A 1 2 3 4 5 6 120 7 8 9 10
XV-Z12000 10 11 12 13 14 15 121 16 17 18 19
XV-Z12000 Ë MAIN UNIT / HAUPT-EINHEIT -4/5 H G F E D C B A 1 2 3 4 5 6 122 7 8 9 10
XV-Z12000 10 11 12 13 14 15 123 16 17 18 19
XV-Z12000 Ë MAIN UNIT / HAUPT-EINHEIT -5/5 H G F E D C B A 1 2 3 4 5 6 124 7 8 9 10
XV-Z12000 10 11 12 13 14 15 125 16 17 18 19
XV-Z12000 Ë KEY UNIT / TASTE-EINHEIT H G F E D C B A 1 2 3 4 126 5 6
XV-Z12000 Ë R/C RECEIVER (Front) Unit / EINLASSEINHEIT (Vorder) H G F E Ë R/C RECEIVER (Rear) Unit / EINLASSEINHEIT (Hinter) D C B A 1 2 3 4 127 5 6
XV-Z12000 Ë IRIS DRIVE UNIT/ BLENDENTREIBER-EINHEIT H G F E D C B A 1 2 3 4 5 6 128 7 8 9 10
XV-Z12000 10 11 12 13 14 15 129 16 17 18 19
XV-Z12000 Ë FORMATTER UNIT / FORMATTER-EINHEIT-1/7 H G F E D C B A 1 2 3 4 5 6 130 7 8 9 10
XV-Z12000 No Use 10 11 12 13 14 15 131 16 17 18 19
XV-Z12000 Ë FORMATTER UNIT / FORMATTER-EINHEIT-2/7 H G F E D C B A 1 2 3 4 5 6 132 7 8 9 10
XV-Z12000 10 11 12 13 14 15 133 16 17 18 19
XV-Z12000 Ë FORMATTER UNIT / FORMATTER-EINHEIT-3/7 H G F E D C B A 1 2 3 4 5 6 134 7 8 9 10
XV-Z12000 10 11 12 13 14 15 135 16 17 18 19
XV-Z12000 Ë FORMATTER UNIT / FORMATTER-EINHEIT-4/7 H G F E D C B A 1 2 3 4 5 6 136 7 8 9 10
XV-Z12000 10 11 12 13 14 15 137 16 17 18 19
XV-Z12000 Ë FORMATTER UNIT / FORMATTER-EINHEIT-5/7 H G F E D C B A 1 2 3 4 5 6 138 7 8 9 10
XV-Z12000 10 11 12 13 14 15 139 16 17 18 19
XV-Z12000 Ë FORMATTER UNIT / FORMATTER-EINHEIT-6/7 H G F E D C B A 1 2 3 4 5 6 140 7 8 9 10
XV-Z12000 10 11 12 13 14 15 141 16 17 18 19
XV-Z12000 Ë FORMATTER UNIT / FORMATTER-EINHEIT-7/7 H G F E D C B A 1 2 3 4 5 6 142 7 8 9 10
XV-Z12000 10 11 12 13 14 15 143 16 17 18 19
XV-Z12000 Ë POWER UNIT / NETZTEINHEIT H G F E D C B A 1 2 3 4 5 6 144 7 8 9 10
XV-Z12000 10 11 12 13 14 15 145 16 17 18 19
XV-Z12000 Ë PC I/F UNIT / PC-I/F-EINHEIT-1/9 H G F E D C B A 1 2 3 4 5 6 146 7 8 9 10
XV-Z12000 10 11 12 13 14 15 147 16 17 18 19
XV-Z12000 Ë PC I/F UNIT / PC-I/F-EINHEIT-2/9 H G F E D C B A 1 2 3 4 5 6 148 7 8 9 10
XV-Z12000 10 11 12 13 14 15 149 16 17 18 19
XV-Z12000 Ë PC I/F UNIT / PC-I/F-EINHEIT-3/9 H G F E D C B A 1 2 3 4 5 6 150 7 8 9 10
XV-Z12000 10 11 12 13 14 15 151 16 17 18 19
XV-Z12000 Ë PC I/F UNIT / PC-I/F-EINHEIT-4/9 H G F E D C B A 1 2 3 4 5 6 152 7 8 9 10
XV-Z12000 10 11 12 13 14 15 153 16 17 18 19
XV-Z12000 Ë PC I/F UNIT / PC-I/F-EINHEIT-5/9 H G F E D C B A 1 2 3 4 5 6 154 7 8 9 10
XV-Z12000 10 11 12 13 14 15 155 16 17 18 19
XV-Z12000 Ë PC I/F UNIT / PC-I/F-EINHEIT-6/9 H G F E D C B A 1 2 3 4 5 6 156 7 8 9 10
XV-Z12000 10 11 12 13 14 15 157 16 17 18 19
XV-Z12000 Ë PC I/F UNIT / PC-I/F-EINHEIT-7/9 H G F E D C B A 1 2 3 4 5 6 158 7 8 9 10
XV-Z12000 10 11 12 13 14 15 159 16 17 18 19
XV-Z12000 Ë PC I/F UNIT / PC-I/F-EINHEIT-8/9 H G F E D C B A 1 2 3 4 5 6 160 7 8 9 10
XV-Z12000 10 11 12 13 14 15 161 16 17 18 19
XV-Z12000 Ë PC I/F UNIT / PC-I/F-EINHEIT-9/9 H G F E D C B A 1 2 3 4 5 6 162 7 8 9 10
XV-Z12000 10 11 12 13 14 15 163 16 17 18 19
XV-Z12000 Ë LED UNIT/ LED-EINHEIT H G F E D C B A 1 2 3 4 164 5 6
XV-Z12000 H PRINTED WIRING BOARD ASSEMBLIES LEITERPLATTENEINHEITEN G F E Power Unit (Component Side) Netzteinheit (Bestückungsseite) D C B A Power Unit (Wiring Side) Netzteinheit (Leiterbahnseite) 1 2 3 4 165 5 6
XV-Z12000 H G F E D C B Main Unit (Component Side) Haupt-einheit (Bestückungsseite) A 1 2 3 4 5 6 166 7 8 9 10
XV-Z12000 10 11 12 13 14 15 167 16 17 18 19
XV-Z12000 H G F E D C B Main Unit (Wiring Side) Haupt-einheit (Leiterbahnseite) A 1 2 3 4 5 6 168 7 8 9 10
XV-Z12000 10 11 12 13 14 15 169 16 17 18 19
XV-Z12000 H G Key Unit (Component Side) Taste-Einheit (Bestückungsseite) F E D R/C Receiver (Rear) Unit (Component Side) Einlasseinheit (Hinter) (Bestückungsseite) R/C Receiver (Front) Unit (Component Side) Einlasseinheit (Vorder) (Bestückungsseite) C B LED Unit (Component Side) LED-Einheit (Bestückungsseite) IRIS DRIVE Unit (Component Side) BLENDENTREIBER-Einheit (Bestückungsseite) A 1 2 3 4 170 5 6
XV-Z12000 H G Key Unit (Wiring Side) Taste-Einheit (Leiterbahnseite) F E D R/C Receiver (Rear)Unit (Wiring Side) Einlasseinheit (Hinter) (Leiterbahnseite) R/C Receiver (Front)Unit (Wiring Side) Einlasseinheit (Vorder) (Leiterbahnseite) C B LED Unit (Wiring Side) LED-Einheit (Leiterbahnseite) IRIS DRIVE Unit (Wiring Side) BLENDENTREIBER-Einheit (Leiterbahnseite) A 1 2 3 4 171 5 6
XV-Z12000 H G F E D C B PC I/F Unit (Component Side) PC-I/F-einheit (Bestückungsseite) A 1 2 3 4 172 5 6
XV-Z12000 H G F E D C B PC I/F Unit (Wiring Side) PC-I/F-einheit (Leiterbahnseite) A 1 2 3 4 173 5 6
XV-Z12000 H G F E FORMATTER Unit (Component Side) FORMATTER-einheit (Bestückungsseite) D C B A FORMATTER Unit (Wiring Side) FORMATTER-einheit (Leiterbahnseite) 1 2 3 4 174 5 6
XV-Z12000 Ref. No. Part No. ★ Description PARTS LIST Code Ref. No. ★ Part No. Description Code ERSATZTEILLISTE PARTS REPLACEMENT AUSTAUSCH VON TEILEN Parts marked with "å" are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set. Ersatzteile, die besondere Sicherheitseigenschften haben, sind in dieser Anleitung markiert.
XV-Z12000 Ref. No. ★ Part No.
XV-Z12000 Ref. No. Part No. ★ Description Code Ref. No.
XV-Z12000 Ref. No. ★ Part No. Description Code Ref. No.
XV-Z12000 Ref. No. Part No. ★ Description Code Ref. No.
XV-Z12000 Ref. No. Part No. ★ Description Code Ref. No. ★ Part No.
XV-Z12000 Ref. No. ★ Part No. Description Code Ref. No. Description DUNTKC175DE01 DUNTKB474FE03 LED UNIT FORMATTER UNIT J LED RED & BLUE J LED RED & BLUE J LED RED IC9001 IC9002 IC9003 IC9004 IC9005 IC9101 IC9102 IC9201 IC9202 IC9203 IC9301 IC9401 IC9402 IC9403 AM AM AC CAPACITOR C2204 VCKYCY1CB104K J 0.1 16V Ceramic AB RESISTORS J J J J J R2213 R2214 R2215 R2216 R2217 VRS-TV1JD182J VRS-TV1JD472J VRS-TV1JD102J VRS-TV1JD102J VRS-TV1JD472J P2450 QPLGN0758REZZY J Plug, 7pin(RE) 1.8k 4.
XV-Z12000 Ref. No. Part No. ★ Description Code Ref. No.
XV-Z12000 Ref. No. ★ Part No. Description Code DUNTKB474FE03 FORMATTER UNIT(Continued) C9542 C9543 C9544 C9545 C9546 C9547 C9548 C9549 C9550 C9551 VCKYCY1EB104KY VCKYCY1EB104KY VCKYCY1EB104KY VCKYCY1EB104KY VCKYCY1EB104KY VCKYCY1EB104KY VCKYCY1EB104KY VCKYCY1EB104KY VCKYCY1AB105KY VCKYCY1AB105KY J J J J J J J J J J 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.
XV-Z12000 Ref. No. ★ Part No. Description Code Ref. No.
XV-Z12000 Ref. No. ★ Part No.
XV-Z12000 Ref. No. R7407 R7408 R7409 R7411 R7412 R7413 R7414 R7415 R7416 R7417 R7418 R7419 R7420 R7421 R7430 R7431 å R7432 å R7433 å R7434 Part No. ★ Description Code Ref. No. ★ Part No.
XV-Z12000 Ref. No. ★ Part No. Description Code Ref. No.
XV-Z12000 Ref. No. Part No. ★ Description Code Ref. No.
XV-Z12000 Ref. No. Part No. ★ Description Code Ref. No.
XV-Z12000 Ref. No. Part No. ★ Description Code Ref. No.
XV-Z12000 Ref. No. Part No. ★ Description Code Ref. No.
XV-Z12000 CABINET AND MECHANICAL PARTS/ GEHÄUSE UND MECHANISCHE BAUTEILE 11-3 H 72 1-4 72 57 1-1-5 11-1 1-1-4 1 1-13 1-1-3 1-16 11 1-1-6 9 1-4 11-4 1-8 1-1-1 80 1-8 9-3 32 70 16 D 1-20 C 25 38 77 1-8 G 37 29 1-1-2 B 1-14 37 N 1-2 11-2 38 14 1-7 1-7 9-1 K M 29 1-1-9 1-8 1-20 L 72 46 1-5 32 1-15 17 1-20 H 77 1-9 1-20 1-10 1-1 1 G 55 1-1-8 64 F 1-3 1-20 A 1-19 12 O 26 77 P J 1-12 1-1 1-1-10 9-2 32 A 72 13 79 1-6 50 78 1-20 1
XV-Z12000 Ref. No. Part No. ★ Description Code Ref. No.
XV-Z12000 Ref. No. Part No. ★ Description Code Ref. No.
XV-Z12000 OPTICS MECHANISM PARTS/ TEILE FÜR OPTIKMECHANISMUS H 6-19 6-20 6-21 6-8 8-17 G 6-15 6-16 6-16 6-7 6-12 6-6 6-22 8-13 6-11 6-9 6-14 F 6-13 8-16 6-2 6-10 6-18 6-17 8-9 8-7 8-11 E 6-5 8-8 8-11 8-11 8-12 6-4 8-10 8-11 8-5 6-5 8-3 8-6 8-4 6-1 6-5 6-4 6-3 6-5 8-5 D 8-4 8-4 7-1 6 8-14 7-7 8-2 8-1 C 7-2 7-3 7-6 7 B 7-6 7-4 7-6 7-7 7-5 7-7 7-6 7-6 A 1 2 3 4 195 5 6
XV-Z12000 Ref. No. Part No. ★ Description Code Ref. No. å å J AC Cord for U.S. AL J AC Cord for U.K., AX Hong Kong and Singapore QACCVA011WJPZ J AC Cord for Europe without AT U.K. and Korea QACCLA018WJPZ J AC Cord for Australia and AU New Zealand RRMCGA216WJSA J R/C Unit BB UDSKAA040WJZZ J CD ROM AM TiNS-A970WJZZ J Projector Operation manual BA for U.S.
XV-Z12000 Part No. ★ Description Ref. No. Part No. ★ Description PACKING OF THE SETCode / VERPACKEN DES GERÄTS Ref. No. Code Polystyrene Bag (SSAKA0170CEZZ ) CD ROM (UDSKAA040WJZZ) Projector Operation Manual (TiNS-A970WJZZ for U.S.) (TiNS-A972WJZZ for European 7 language) (TiNS-A973WJZZ for Chinese, Korean and Arabic language) CD ROM Operation Manual (TiNS-B097WJZZ) Video Cable (QCNWGA001WJZZ except for U.S. ) DVI to 15pin D-Sub Adaptor (QCNWGA010WJPZ except for U.S.
XV-Z12000 Ref. No. Part No. ★ Description Code Ref. No. ★ Part No. Description Code COPYRIGHT © 2004 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher. TQ1673-S Jan.