XL-MP130 MICRO COMPONENT SYSTEM Thank you for purchasing this SHARP product. To obtain the best performance from this product, please read this manual carefully. It will guide you in operating your SHARP product. XL-MP110E Micro Component System consisting of XL-MP110E (main unit) and CP-MP110E (speaker system). MODEL XL-MP110E OPERATION MANUAL Accessories Please confirm that the following accessories are included. Remote control 1 AM loop aerial 1 Note: Only the above accessories are included.
XL-MP110E Contents Special notes Important Instruction WARNINGS When the ON/STAND-BY button is set at STAND-BY position, mains voltage is still present inside the unit. When the ON/ STAND-BY button is set at STAND-BY position, the unit may be brought into operation by the timer mode or remote control. This unit contains no user serviceable parts. Never remove covers unless qualified to do so.
Precautions XL-MP110E General Please ensure that the equipment is positioned in a well-ventilated area and ensure that there is at least 10 cm (4") of free space along the sides, top and back of the equipment. 10 cm (4") 10 cm (4") Hold the AC power plug by the head when removing it from the wall socket, as pulling the lead can damage internal wires. Do not remove the outer cover, as this may result in electric shock. Refer internal service to your local SHARP service facility.
XL-MP110E Controls and indicators Front panel Reference page 1. Disc Trays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 2. Timer Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 3. On/Stand-by Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 4. Clock/Timer Button . . . . . . . . . . . . . . . . . . . . . . . . . 13, 27, 30 5. Tape Record Pause Button . . . . . . . . . . . . . . . . . . . . . . 25, 34 6.
XL-MP110E 10 11 12 13 1 2 3 4 5 6 7 8 9 14 Reference page 1. Disc Number Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 2. Disc Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 3. Disc Pause Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 4. Memory Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 5. Disc Repeat Play Indicator . . . . . . . . . . . . . . . . . . . . . . . . . 19 6.
XL-MP110E Controls and indicators (continued) Rear panel 3 ANTENNA AM LOOP Reference page 1. Speaker Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2. AC Power Lead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3. FM 75 Ohms Aerial Socket . . . . . . . . . . . . . . . . . . . . . . . . . 10 4. AM Loop Aerial Socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 5. Video/Auxiliary (Audio Signal) Input Sockets . . . . . . . . . . 31 6.
XL-MP110E 1 2 3 11 12 7 13 14 15 16 17 18 19 20 21 8 9 22 23 24 4 5 6 10 Reference page 1. Remote Control Transmitter . . . . . . . . . . . . . . . . . . . . . . . . 11 2. Disc Clear/Dimmer Button . . . . . . . . . . . . . . . . . . . . . . 12, 20 3. Disc Number Select Buttons . . . . . . . . . . . . . . . . . . . . . . . . 14 4. Disc Random Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 5. Disc Stop Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
XL-MP110E System connections Make sure to unplug the AC power lead before any connections. Aerial connection (see page 9) AM loop aerial FM aerial Right speaker Preparation for Use Left speaker ANTENNA AM LOOP FM 75 OHMS VIDEO/AUX IN RIGHT LEFT AC INPUT SPEAKERS RATED SPEAKER IMPEDANCE: 6 OHMS MIN.
XL-MP110E Speaker connection Connect the black wire to the minus (-) terminal, and the red wire to the plus (+) terminal. Supplied AM loop aerial: Connect the AM loop aerial to the AM LOOP socket. Position the AM loop aerial for optimum reception. Place the AM loop aerial on a shelf, etc., or attach it to a stand or a wall with screws (not supplied).
XL-MP110E System connections (continued) AC power connection Demonstration mode After checking all the connections have been made correctly, plug the AC power lead of this unit into the wall socket. If you plug in the unit first, the unit will enter the demonstration mode. ANTENNA To cancel the demonstration mode: When the unit is in the power standby mode (demonstration mode), press the X-BASS/DEMO button. The unit will enter the low power consumption mode.
Remote control Battery installation Use 2 "AA" size batteries (UM/SUM-3, R6, HP-7 or similar). Batteries are not included. 1 2 3 Open the battery cover. Insert the batteries according to the direction indicated in the battery compartment (back of the battery cover). When inserting or removing the batteries, push them towards the battery terminals. Close the cover. XL-MP110E Notes concerning use: Replace the batteries if the operating distance is reduced or if the operation becomes erratic.
XL-MP110E General control Volume control / / Main unit operation: When the VOL +/- control is turned clockwise, the volume will increase. When it is turned anti-clockwise, the volume will decrease. Remote control operation: Press the VOLUME (+ or -) button to increase or decrease the volume. 0 ..... 30 MAXIMUM Bass control Basic Operation When the power is first turned on, the unit will enter the extra bass mode which emphasises the bass frequencies, and "X-BASS" will appear.
Setting the clock XL-MP110E 5 / Press the or button once to advance the time by 1 hour. Hold it down to advance continuously. 6 In this example, the clock is set for the 24-hour (0:00) display. 4 Press the ON/STAND-BY button to turn the power on. Press the CLOCK/TIMER button. Within 10 seconds, press the or button to select "CLOCK", and press the MEMORY/SET button. Press the or button to select 12-hour or 24hour display and then press the MEMORY/SET button.
XL-MP110E Listening to a CD or MP3/WMA disc CD or MP3/WMA disc Playback This system can play back a standard CD, CD-R/RW in the CD format and CD-R/RW with MP3 or WMA files, but cannot record on them. Some audio CD-R and CD-RW discs may not be playable due to the state of the disc or the device that was used for recording. MP3: MP3 is a form of compression. It is an acronym which stands for MPEG Audio Layer 3.
XL-MP110E Press the ON/STAND-BY button to turn the power on. 4 Place the disc on the disc tray 1, label side up. Be sure to place 8 cm (3") disc in the middle of the disc trays. Press the CD button. Press the 1 button and within 5 seconds, press the OPEN/CLOSE button to open the disc tray 1. 12 cm (5") 8 cm (3") Playback will begin from track 1 on DISC 1. After that disc finishes playing, the next disc will automatically play.
XL-MP110E Listening to a CD or MP3/WMA disc (continued) Various disc functions CD or MP3/WMA disc Playback Function Remote control Operation Play Press in the stop mode. Stop Press in the playback mode. Pause Press in the playback mode. Press the / button to resume playback from the paused point. Press in the playback or stop mode. If you press the button in the stop mode, press the / button to start the desired track.
XL-MP110E To select the desired folder or track by name (MP3/WMA discs only) 1 Whilst in the stop mode, press the DISPLAY button to display the folder name. [When in the stop mode] 2 Select the desired folder by pressing the button. 3 Press the DISPLAY button to display the track name. 4 Select the desired track by pressing the button. 5 Press the / (CD to begin playback.
XL-MP110E Advanced CD or MP3/WMA disc playback To specify a disc to play You can play a disc by specifying the disc number. CD or MP3/WMA disc Playback 1 Press one of the 1- 5 buttons to select the desired disc. Use the direct search buttons on the remote control to select the desired track whilst playing the selected disc. Selected track number Selected disc number 2 Within 5 seconds, press the CD DIRECT PLAY button on the main unit. The direct search buttons allow you to select up to number 9.
XL-MP110E To repeat all tracks on up to 5 discs: Press the / button twice. Random play The tracks on the disc(s) can be played in random order automatically. To random play all tracks on up to 5 discs: Press the RANDOM button on the remote control. To repeat desired tracks: Perform steps 1 - 6 in "Programmed play" section on page 20 and then press the / button twice. To cancel random play: Press the / (CD / ) button. "NORMAL" will appear for 2 seconds. To cancel repeat play: Press the / button again.
XL-MP110E Advanced CD or MP3/WMA disc playback (continued) Programmed play Whilst in the stop mode, press the MEMORY/SET (MEMORY) button to enter the programming save mode. To clear the programmed selections: Press the CLEAR/DIMMER button on the remote control whilst the "MEMORY" indicator is flashing. Each time the button is pressed, one track will be cleared, beginning with the last track programmed. Press one of the 1 - 5 buttons to select the desired disc.
Listening to the radio XL-MP110E Tuning / / 1 2 Press the ON/STAND-BY button to turn the power on. 3 Press the TUNING ( station. Press the TUNER (BAND) button repeatedly to select the desired frequency band (FM or AM). or ) button to tune in to the desired Notes: When radio interference occurs, auto scan tuning may stop automatically at that point. Auto scan tuning will skip weak signal stations. To stop the auto tuning, press the TUNING button again.
XL-MP110E Listening to the radio (continued) Memorising a station Radio You can store 40 AM and FM stations in memory and recall them at the push of a button. (Preset tuning) 1 2 Perform steps 1 - 3 in "Tuning" on page 21. 3 Within 30 seconds, press the PRESET ( or ) button to select the preset channel number. Store the stations in memory, in order, starting with preset channel 1. 4 Within 30 seconds, press the MEMORY/SET (MEMORY) button to store that station in memory.
Listening to a cassette tape Before playback: For playback, use normal or low-noise tapes for the best sound. (Metal or CrO tapes are not recommended.) Do not use C-120 tapes or poor-quality tapes, as they may cause malfunctions. Before loading a tape into the cassette compartment, tighten the slack with a pen or a pencil. / XL-MP110E Tape playback 1 2 3 Press the ON/STAND-BY button to turn the power on. 4 Load a cassette into the cassette compartment with the side to be played on facing you.
XL-MP110E Listening to a cassette tape (continued) Various tape functions Tape Playback Function Main unit Remote control Operation Playback Press in the stop mode. Stop Press in the playback, fast forward or rewind mode. Fast forward/ Rewind Press in the playback or stop mode. Before recording: When recording important selections, make a preliminary test to ensure that the desired material is properly recorded.
XL-MP110E Recording from a CD or MP3/WMA disc You can record the desired disc using the CD DIRECT PLAY button. / 1 2 3 / 4 Press the ON/STAND-BY button to turn the power on. Press the CD button. Load a cassette into the cassette compartment with the side to be recorded on facing you. Wind past the leader of the tape, on which recording cannot be performed. Press the button. 5 6 Press one of the 1- 5 buttons to select the desired disc.
XL-MP110E Recording on a cassette tape (continued) Recording from several CDs continuously: 1 Perform steps 1 - 5 in "Recording from a CD or MP3/WMA disc" on page 25. 2 Within 5 seconds, press the / (TAPE ) button to start recording. To perform programmed recording: 1 Programme discs and tracks (see page 20). 2 Press the button. 3 Press the / (TAPE ) button to start recording. Tape Recording To stop recording: Press the (TAPE ) button. The CD and tape will stop.
Timer and sleep operation XL-MP110E Timer playback: The unit turns on and plays the desired source (CD, tuner, tape) at a preset time. / Timer recording: The unit turns on and starts recording from the tuner at the preset time. / This unit has 2 types of timer: ONCE TIMER and DAILY TIMER. Once timer play or once timer recording works for one time only at a preset time. For example, if you are away but want to record a programme on a radio station.
XL-MP110E Timer and sleep operation (continued) 4 Within 10 seconds, press the or button to select "ONCE SET" or "DAILY SET", and press the MEMORY/ SET button. 5 Press the or button to select "PLAY" or "REC", and press the MEMORY/SET button. Advanced Features White Red The illustrations show the daily timer setting. 6 Press the or button to adjust the hour and then press the MEMORY/SET button. 9 Switch input with the or button, and then press the MEMORY/SET button.
XL-MP110E start. The volume will increase gradually until it reaches the preset volume. 13 When the timer end time is reached, the system will enter the power stand-by mode automatically. Once timer: The timer will be cancelled. Daily timer: The timer will operate at the same time every day. It will continue until the daily timer setting is cancelled. Cancel the daily timer when it is not in use.
XL-MP110E Timer and sleep operation (continued) Sleep operation The radio, compact disc and cassette tape can all be turned off automatically. Advanced Features 1 2 3 4 Play back the desired sound source. Press the CLOCK/TIMER button. Within 10 seconds, press the or button to select "SLEEP", and press the MEMORY/SET button. Press the or button to select the time.
Enhancing your system XL-MP110E Listening to the playback sounds from VCR, DVD, etc. The connection lead is not included. Purchase a commercially available lead as shown below. 1 When using video equipment, connect the audio output to this unit and the video output to a television. To the line output sockets ANTENNA White AM LOOP FM 75 OHMS Red VIDEO/AUX IN RIGHT LEFT Use a connection lead to connect the VCR, DVD, etc. to the VIDEO/AUX IN sockets.
XL-MP110E Enhancing your system (continued) Subwoofer connection When a commercially available speaker with a built-in amplifier is connected to this unit, you can enjoy sound with emphasised bass. Connect an RCA lead from a commercially available speaker with a built-in amplifier to the SUBWOOFER PRE-OUT socket. ANTENNA Many potential problems can be resolved by the owner without calling a service technician.
XL-MP110E Cassette deck Cannot record tracks with proper sound quality. Cannot erase completely. Sound skipping. Cannot hear treble. Sound fluctuation. Cannot remove the tape. Possible cause Is the erase-prevention tab removed? Is it a normal tape? (You cannot record on a metal or CrO tape.) Is there any slack? Is the tape stretched? Are the capstans, pinch rollers, or heads dirty? If a power failure occurs during playback, the heads remain engaged with the tape.
XL-MP110E Troubleshooting chart (continued) If trouble occurs When this product is subjected to strong external interference (mechanical shock, excessive static electricity, abnormal supply voltage due to lightning, etc.) or if it is operated incorrectly, it may malfunction. If such a problem occurs, do the following: 1 Set the unit to the stand-by mode and turn the power on again. 2 If the unit is not restored in the previous operation, unplug and plug in the unit, and then turn the power on.
Maintenance XL-MP110E Cleaning the tape-handling parts Cleaning the cabinet Dirty heads, capstans or pinch rollers can cause poor sound and tape jams. Clean these parts with a cotton swab moistened with commercial head/pinch roller cleaner or isopropyl alcohol. When cleaning the heads, pinch rollers, etc., unplug the unit which contains high voltages. Pinch roller Capstan D B Caution: Do not use chemicals for cleaning (petrol, paint thinner, etc.). It may damage the cabinet finish.
XL-MP110E Specifications As part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.
MEMO CD-MEMO.
MEMO CD-MEMO.
FOR LOCATION ENQUIRIES WITHIN FOR LOCATION ENQUIRIES WITHIN AUSTRALIA NEW ZEALAND REGARDING YOUR LOCAL REGARDING YOUR LOCAL SHARP APPROVED SERVICE CENTRE SHARP APPROVED SERVICE CENTRE VISIT OUR WEBSITE AT VISIT OUR WEBSITE AT www.sharp.net.au www.sharp.net.
WARRANTY Consumer Electronic Products Congratulations on Your Purchase! This Sharp product is warranted against faults in materials and manufacture for a period of twelve(12) months from the date of original purchase. If service is required during the warranty period, please contact your nearest Sharp Approved Service Centre. These repairs would be carried out at no charge to the owner, subject to the conditions specified herein.
