Specifications

E-12
Sleep operation■
The radio, compact disc and USB can all be turned off
automatically.
Play back the desired sound source.
Press the SLEEP button.
Within 5 seconds, press the SLEEP button repeatedly
to select the time.
SLP 120 90 60 30 15 10 5
“SLEEP” will appear.
The unit will enter the power stand-by mode
automatically after the preset time has elapsed.
To confi rm the remaining sleep time:
Whilst “SLEEP” is indicated, press the SLEEP button. The
remaining time is displayed for about 10 seconds.
To cancel the sleep operation:
Press the ON/STAND-BY button whilst “SLEEP” is
indicated. To cancel the sleep operation without setting the
unit to the stand-by mode, proceed as follows.
Whilst “SLEEP” is indicated, press the SLEEP button
repeatedly until SLEEP indicator disappears.
1
2
3
4
5
To use timer and sleep operation together■
Sleep and timer playback:
For example, you can fall asleep listening to the radio and
wake up to CD in the next morning.
Set the sleep time (refer to the column on the left,
steps 1 - 5).
Whilst the sleep timer is set, set the timer playback
(steps 2 - 8, pages 10 - 11).
1
2
Sleep timer
setting
Timer playback
setting
End time
Timer playback
start time
Sleep operation will
automatically stop
Desired time5 - 120 minutes
Adjust the volume using the VOLUME + or VOLUME
– and then press the MEMORY button. (Do not turn the
volume up too high).
Press the ON/STAND-BY button to enter the power
stand-by mode. The TIMER red indicator lights up and
the unit is ready for timer playback.
When the preset time is reached, playback will start.
The volume will increase gradually until it reaches the
preset volume. The “ ” indicator will blink during timer
playback.
Checking the timer setting:
Press the CLOCK/TIMER button repeatedly to view as
follows:
Cancelling the timer setting:
Press the CLOCK/TIMER button for about 2 seconds.
Within 5 seconds, press
or to select “OFF” and
press MEMORY button.
Note:
After selecting the volume level and press the MEMORY
button to confi rm, it will change to last function.
8
9
10
Timer and sleep operation (Remote control only) (continued)
MICRO COMPONENT SYSTEM XL-DAB1
Headphones■
Enhancing your system
The connection cord is not included. Purchase a
commercially available cord as shown below.
Portable audio
player, etc.
Audio cable
(not supplied)
Use a connection lead to connect the portable audio
player etc. to the AUDIO IN socket.
Press the ON/STAND-BY button to turn the power on.
Press the AUDIO IN button on the remote control or
FUNCTION button repeatedly on main unit to select
AUDIO IN function.
Play the connected equipment. If volume level of the
connected device is too high, sound distortion may
occur. Should this happen, lower the volume of the
connected device. If volume level is too low, increase
the volume of the connected device.
Note:
To prevent noise interference, place the unit away from the
television.
1
2
3
4
Listening to the playback sounds of
portable audio player, etc.
■
Do not turn the volume on to full at switch on and listen
to music at moderate levels. Excessive sound pressure
from earphones and headphones can cause hearing
loss.
Before plugging in or unplugging the headphones,
reduce the volume.
Be sure your headphones have a 3.5 mm (1/8”)
diameter plug and impedance between 16 and 50
ohms. The recommended impedance is 32 ohms.
Plugging in the headphones disconnects the speakers
automatically. Adjust the volume using the VOLUME
control.
●
●
●
●
XL-DAB1H_AUS (A5).indd 12XL-DAB1H_AUS (A5).indd 12 6/21/2010 9:12:56 AM6/21/2010 9:12:56 AM