Specifications

E-2
Remote control
Battery installation■
Open the battery cover.
Insert the supplied battery according to the terminal indicated in
the battery compartment.
When inserting or removing the battery, push it towards the (–)
battery terminals.
Close the cover.
Caution:
Replace all old batteries with new ones at the same time.
Do not mix old and new batteries.
Remove the battery if the unit will not be used for a long period of
time. This will prevent potential damage due to battery leakage.
Do not use rechargeable battery (nickel-cadmium battery, etc.).
Installing the battery incorrectly may cause the unit to
malfunction.
Batteries (battery pack or batteries installed) shall not be exposed to
excessive heat such as sunshine, re or the like.
Notes: concerning use:
Replace the battery if the operating distance is reduced or if the
operation becomes erratic. Purchase two “AAA” size batteries
(UM-4, R03, HP-16 or similar).
Periodically clean the transmitter on the remote control and the
sensor on the unit with a soft cloth.
Exposing the sensor on the unit to strong light may interfere with
operation. Change the lighting or the direction of the unit if this
occurs.
Keep the remote control away from moisture, heat, shock, and
vibrations.
Test of the remote control■
Check the remote control after checking all the connections.
Point the remote control directly at the remote sensor on the unit. The remote
control can be used within the range shown below:
Remote sensor
0.2 m - 6 m
(8” - 20’ )
�
2�
3�
4�
●
●
●
●
●
●
●
●
●
●
General control
Turning the Power On■
Press ON/STAND-BY on the remote control or on the main unit to
turn on the power.
Entering standby
Press ON/STAND-BY on the remote control or on the main unit to
enter standby.
Note:
When you turn on this unit for the rst time after purchase or
when you turn on this unit after you perform “System Reset” (see
page 29), the language setting screen will be displayed, so please
perform the language setting (see step 3 of page 13).
If you press ON/STAND-BY again immediately after entering standby,
the Unit may not turn on. If this happens, wait for 10 seconds or more
and then turn on the power again.
About the Home screen
When turning on the unit on DISC function, the Home screen appears.
Home screen
Video
Music
Picture
BD-Video
USB
e-Contents
Settings
ENTER EXIT
Select
Enter Return Exit
1
5
32 4
Home Network
Main menu
Icon for disc inserted
Icon for USB memory device connected
Icon for LAN connection
Button Guide
●
●
1�
2�
3�
4�
5�
Display brightness control■
To dim the display brightness, press and hold the DISPLAY <DIM>
button on the remote control for more than 2 seconds.
The display brightness will change each time the DISPLAY <DIM>
button is pressed for more than 2 seconds.
Dimmer 1
Dimmer 2
Dimmer off
(Display is dim).
(Display gets dimmer).
(Display is bright).
Volume auto fade-in■
If you turn off and on the main unit with the volume set to 80 or higher, the
volume starts at 40 and fades in to the last set level.
Volume control■
Turn the volume knob towards VOLUME +/– (on main unit) or press
VOL. +/– (on remote control) to increase or decrease the volume.
Speaker output selection (HDMI connection)■
By using HDMI connection, you have an option to listen to the sound
output either from this unit or your TV.
To select the preferred speaker output, press and hold TV (ARC)
button on the remote control until “TV Speaker” or “BD601 Speaker”
appears on the display.
Auto power on function■
When you press any of the following buttons, the unit turns on.
iPod <TV OUT>, DISC, INPUT, TUNER, TV (ARC) on the remote
control: Selected function is activated.
/ or OPEN/CLOSE button on the main unit: The unit turns on
and playback of the last function will start (DISC, TUNER, USB-2
(iPod), iPod, AUDIO IN, LINE IN, DIGITAL IN, TV ARC)
Auto power off function■
The main unit will enter the stand-by mode (when iPod or iPhone is not
docked) after 15 minutes of inactivity during:
iPod/USB-2 (iPod): No connection.
DISC: In the stop mode.
AUDIO IN/LINE IN/DIGITAL IN/ TV ARC: No detection of input signal
or very low sound audibility
Note:
However, if iPod or iPhone is docked, the unit will begin charging.
“Charge Mode” will be displayed.
Muting■
The volume is muted temporarily when pressing the button on the
remote control. Press again to restore the volume.
X-Bass control■
When the power is rst turned on, the unit will enter the extra bass
mode which emphasises the bass frequencies, and X-BASS ON will
appear. To cancel the extra bass mode, press and hold BASS/TREBLE
[X-BASS] button on the remote control.
●
●
●