AN-PHCM20 INSTALLATION INSTRUCTIONS FOR MOUNTING BRACKET FOR USE ONLY WITH SHARP PROJECTOR MODEL XG-PH50X CEILING MOUNTING BRACKET AN-PHCM20 CEILING MOUNTING BRACKET COMBINED WITH OPTIONAL ADJUSTABLE EXTENSION TUBE MODEL AN-EP101B COPYRIGHT © 2005 SHARP ELECTRONICS CORPORATION
INSTALLATION INSTRUCTIONS CEILING BRACKET AN-PHCM20 C A U T I O N INSTALLATION OF THIS ADJUSTABLE CEILING MOUNTING BRACKET SHOULD BE PERFORMED BY QUALIFIED SERVICE/ INSTALLATION PERSONNEL FOLLOWING THE INSTALLATION INSTRUCTIONS THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.
INSTALLATION INSTRUCTIONS CEILING BRACKET AN-PHCM20 FIGURE 1. ILLUSTRATION OF PARTS FOR CEILING BRACKET A. D. C. B. E. F. H. I. J. G. INVERT THE PROJECTOR IMAGE Please refer to the owners manual for your LCD Projector for detailed instructions of how to electrically invert the projected image to accommodate its use in the ceiling mounted mode.
INSTALLATION INSTRUCTIONS 1.1 1.2 CEILING BRACKET AN-PHCM20 a. Select straddle beam or single beam installation. b. Use the ceiling bracket as a template to mark the location where the pilot holes should be drilled. c. Drill the pilot holes for the support screws using a 1/8” drill bit into the center of the beam. (See Figs. 2 and 3). Screw the ceiling plate to the beams. Use at least 6 screws and metal washers supplied with the unit.
INSTALLATION INSTRUCTIONS CEILING BRACKET AN-PHCM20 FIGURE 3 ILLUSTRATION OF SINGLE BEAM CEILING BRACKET INSTALLATION Ceiling Beam Ceiling Mounting Bracket Cable access hole Washers Security Bushing Sheetrock or lath and plaster ceiling 1/4 x 10 Lag Bolts Velcro DO NOT RUN THE AC POWER CORD THROUGH THE CEILING PLATE AND TRIM COVER STEP 2. INSTALL THE CEILING MOUNT PLASTIC TRIM 2.1 The Access Hole (See Fig.
INSTALLATION INSTRUCTIONS CEILING BRACKET AN-PHCM20 STEP 3 DETACH THE POSITIONING ASSEMBLY FROM THE PROJECTOR ATTACHMENT PLATE. FIGURE 5 POSITIONING KNUCKLE ASSEMBLY NOTE: PLEASE LOOK OVER THE EXACT MANNER IN WHICH THE POSITIONING ASSEMBLY AND THE ATTACHMENT PLATE GO TOGETHER SO THAT YOU WILL BE ABLE TO REASSEMBLE THEM WHEN YOU HANG THE PROJECTOR. 3.
INSTALLATION INSTRUCTIONS CEILING BRACKET AN-PHCM20 STEP 5 ATTACH THE POSITIONING ASSEMBLY TO THE CEILING PLATE FIGURE 8 WASHER LOCKING NUT UPPER KNUCKLE IF YOU INTEND TO RUN AUDIO OR VIDEO CABLES THROUGH THE CEILING PLATE PROCEED WITH STEP 5.1 AND 5.2, OTHERWISE PROCEED TO STEP 5.3: 5.1 Cut opening in the ceiling plate trim cover as indicated on the label inside cover near the center bushing. 5.2 Thread cables through the plastic trim cover. 5.
INSTALLATION INSTRUCTIONS CEILING BRACKET AN-PHCM20 STEP 6 HANGING THE PROJECTOR FROM POSITIONING ASSEMBLY IT IS RECOMMENDED THAT TWO PERSONS SUPPORT THE PROJECTOR WHEN RAISING IT UP IN ORDER TO HANG IT IN PLACE. 6.1 Raise the projector with the mounting plate attached and slide the fitting (See Fig. 9) over the support stud on the hanging position. 6.2 Replace the locking nut and split lock washer (removed in step 3.1). Using the 9/16” run the nut up but do not tighten all the way.
INSTALLATION INSTRUCTIONS CEILING BRACKET AN-PHCM20 FIGURE 11 DETAIL OF POSITIONING ASSEMBLY CEILING PLATE PLASTIC CEILING PLATE TRIM COVER LOCKING NUT AND HORIZONTAL POSITION ADJUSTMENT HORIZONTAL TILT ADJUSTMENT VERTICAL POSITION ADJUSTMENT STEP 8 INSTALL THE PLASTIC TRIM COLLAR 8.1 The plastic trim collar may be used as a cosmetic concealment of the positioning adjustment knuckle assembly and the audio and video signal cables. 8.
INSTALLATION INSTRUCTIONS CEILING BRACKET AN-PHCM20 DIMENSIONS AND MEASUREMENTS OF COMPONENTS FOR SHARP MOUNTING BRACKET AN-MBCM10 CEILING PLATE 4” WIDE X 18” LONG DISTANCE BETWEEN SETS OF MOUNTING HOLES: 1st SET 12”, 2nd SET 14”, 3rd SET 16” ADDITIONAL POSSIBLE COMBINATIONS OF MOUNTING HOLE DISTANCE 13” & 15” THREAD SIZE OF SWIVEL SHAFT & CEILING PLATE BUSHING 1/2” X 20 15 ” VELCRO 4” VELCRO 12” 14” 16” 18” SECURITY ANCHOR FITTING CENTER BUSHING 7/8” DEEP 1/2X20 THREADED HOLE CABLE ACCESS HOLE ATTAC
INSTALLATION INSTRUCTIONS CEILING BRACKET AN-PHCM20 ONE YEAR LIMITED WARRANTY SHARP Electronics Corporation warrants to the first end use purchaser, that this SHARP brand product (the “Product”), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective product or part thereof at no charge to the purchaser for parts or for labor, excluding costs of removal and/or installation, for
COPYRIGHT © 2005 SHARP ELECTRONICS CORPORATION
AN-PHCM20 SUPPLEMENTAL INSTRUCTIONS FOR INSTALLATION OF 2” EXTENSIONS TO LOWER MOUNTING BRACKET FROM CEILING. CEILING PLATE COVER INSTALL ONE 2” EXTENSION OR TWO 2” EXTENSIONS HERE AS NEEDED. CONTINUE WITH STEP 5 OF THE INSTALLATION INSTRUCTIONS.
