Specifications

ManualsBrandsSharp ManualsProjectorsXG-P20XU

Quick Start Reference Sheet

Sharp XG-P20XU

Revision B

DR-SHP17 – 9/04/02 SP Controls reserves the right to modify specifications without notice at any time.

NOTE: This document is intended only as a quick reference for installation – please read the following

SP Controls Application Note for a complete description of this projector driver prior to installation.

I. Driver Features

1. Input Selection Mapping

Selection 1: INPUT 1 (VGA)

Selection 2: INPUT 2 (5 BNC)

Selection 3: INPUT 4 (RCA)

Selection 4: INPUT 5 (S-Video)

2. Hidden Function Mapping

Selection 1: BLACK SCREEN

Selection 2: ENTER

Selection 3: ADJUST LEFT

Selection 4: ADJUST RIGHT

Off: MENU

Volume Up: ADJUST UP

Volume Down: ADJUST DOWN

3. Other Driver Features

Power Status Feedback Method Current Sensor

Control Wiring Option Wired Remote or IR Emitter

NOTE: Due to an interoperability issue, Power Polling for this projector is not available. If power feedback

is required, we recommend using a third party power current sensor. If the projector's automatic shutoff

timers are disabled, the SmartPanel will reliably remain in sync with the projector unless the projector is

powered on or off manually.

II. Wiring Specifications

NOTE: For a wiring diagram, please see the SP Controls Application Note for the Sharp XG-P20XU

1. RS-232:

Wire the Panel RS-232 port to a female DB9 as follows:

RX to 2

TX to 3

GND to 5

JUMPER 7 and 8

Connect this female DB9 to the projector port labeled RS-232C.

2. Infrared Emitter:

Wire the Panel IR/Serial port to a female 1/8" Mini as follows:

IR/SER to tip

GND to ring

Attach to the projector port labeled Wired Remote using a male 1/8” mini to male 1/8” mini (not

included).

III. Additional Projector Information

1. If the Panel is wired to the Projector’s Wired Remote port, the Wired Remote port must be manually

switched to IR on the projector.

2. You must set the Economy Mode labeled “MNTR Out/RS232C” to OFF. If you leave this setting on,

the Sharp will not respond to RS-232 control when in standby mode. See Application Note Section V.

Special Control Note for instructions.

Summary of content (8 pages)

PAGE 1
Quick Start Reference Sheet Sharp XG-P20XU Revision B NOTE: This document is intended only as a quick reference for installation – please read the following SP Controls Application Note for a complete description of this projector driver prior to installation. I. Driver Features 1. Input Selection Mapping Selection 1: Selection 2: Selection 3: Selection 4: INPUT 1 (VGA) INPUT 2 (5 BNC) INPUT 4 (RCA) INPUT 5 (S-Video) 2.
PAGE 2
SmartPanel Projector Driver Application Note Sharp XG-P20XU 3. You should set Economy Mode labeled Auto Power Off feature to OFF. If you leave this setting on, the Sharp will automatically shut itself off when no signal is detected for several minutes. If you desire automatic shutdown, use the Panel’s Automatic Shutdown Timer. See Application Note Section V. Special Control Note for instructions. 4.
PAGE 3
Projector Driver Application Note Sharp XG-P20XU Revision B This document describes the SmartPanel Projector Driver for the Sharp XG-P20XU projector. For information on configuring and using the Panel see the SmartPanel Configuration and Installation Guide. Please read the SPECIAL CONTROL NOTE in Section V of this document before attempting control of the projector. This note describes how the Sharp’s configurable settings impact the projector’s behavior. I. PROJECTOR CONTROL A.
PAGE 4
SmartPanel Projector Driver Application Note Sharp XG-P20XU LENS SELECT is a function that accesses a menu controlling FOCUS, ZOOM, LENS SHIFT, KEYSTONE, and DIGITAL SHIFT. Once this menu is called, use the hidden function ADJUST commands to change settings (while still holding down the ON key). Continue pressing LENS SELECT to toggle through the available LENS SELECT functions.
PAGE 5
SmartPanel Projector Driver Application Note Sharp XG-P20XU The following table specifies settings for the Panel’s configurable timers. For more information on the inactivity shutdown feature and the lockout timer see the SmartPanel Configuration and Installation Guide. Lockout Timer Inactivity Shutdown 65 seconds (see note 3) Disabled © 2002 SP Controls Inc. 601 Minnesota Suite 115 San Francisco, CA 94107 help@spcontrols.
PAGE 6
SmartPanel Projector Driver Application Note Sharp XG-P20XU II. CONTROL WIRING This section specifies how RS-232 and Wired Remote should be wired to the Sharp projector. PROJECTOR CONTROL A. RS-232 should be connected to the Sharp control port labeled RS-232C IN. Connection should be as follows: SENSE GND IR/SER +12V CTS IR/SERIAL GND RTS TX RX RS232 1. Wire the Panel to a female DB9 as follows: RX to 2 TX to 3 GND to 5 JUMPER across 7 and 8 2.
PAGE 7
SmartPanel Projector Driver Application Note Sharp XG-P20XU III. TROUBLESHOOTING Additional tips can be found in the SmartPanel Configuration and Installation Guide. The Projector keeps turning itself off! The Panel turns itself off when power verification indicates that the projector is off (see Note 1). Also, if the Automatic Power Shut-Off Feature is on, the projector will shut itself off if it does not receive a signal after fifteen minutes.
PAGE 8
SmartPanel Projector Driver Application Note Sharp XG-P20XU V. SPECIAL CONTROL NOTE Read before attempting to control the projector The XG-P20XU can be configured with two power saving settings as an Economy Mode. These settings determine whether (a) the projector shuts itself off in the absence of an input signal; and (b) whether the projector responds to RS-232 command when in standby (“off) mode. When installing the P10XU: • You must set the Economy Mode labeled “MNTR Out/RS232C” to OFF.