Operating instructions

-11
Introduction
Optional lenses
 Lens Projection distance for 100" screen size
Wide-zoom lens (× 1.5 – 1.9) AN-C12MZ 10' 5" – 13' 1" (3.2 m – 4.0 m)
Tele-zoom lens (× 2.2 – 2.8) AN-C18MZ 15' 7" – 19' 10" (4.8 m – 6.0 m)
Tele-zoom lens (× 3.3 – 5.1) AN-C27MZ 23' 2" – 35' 8" (7.1 m – 10.9 m)
Tele-zoom lens (× 5.1 – 7.2) AN-C41MZ 36' 2" – 50' 10" (11.0 m – 15.5 m)
The standard zoom lens is attached to the projector.
The optional lenses from Sharp are also available for specialized application. Please see
your nearest Sharp Authorized Projector Dealer for details on all the lenses. (Refer to the
SETUP MANUAL on the supplied CD-ROM for details.) Also, be sure to have service person-
nel install the optional lenses.
Throw Distance
The graph below is for 100 inches (254 cm) screen with 16:10 Signal Input (Normal Mode).
Screen
10 20 30 5040 55(ft)
Standard zoom lens
12'4"–14'9" (3.8 m–4.5 m)
Throw distance ratio 1:1.8–2.1
Tele-zoom lens (AN-C18MZ)
15'7"–19'10" (4.8 m–6.0 m)
Throw distance ratio 1:2.2–2.8
Tele-zoom lens (AN-C27MZ)
23'2"–35'8" (7.1 m–10.9 m)
Throw distance ratio 1:3.3–5.1
Tele-zoom lens (AN-C41MZ)
36'2"–50'10" (11.0 m–15.5 m)
Throw distance ratio 1:5.1–7.2
Wide-zoom lens (AN-C12MZ)
10'5"–13'1" (3.2 m–4.0 m)
Throw distance ratio 1:1.5–1.9
Downloaded From projector-manual.com Sharp Manuals
-17
Quick Start
Pages 31, 32
4. Adjus he agle
5. Adjus he focus ad he zoom
7. Tu r he Power off
Page 30
6. Selec he INPUT mode
Page 34
••
••
• This projector is equipped with an ÒAuto V-Keystone
CorrectionÓ function that automatically corrects any
trapezoidal distortion within the projected image.
Bring the projected image into focus
••
••
• Bring the projected image into focus by
rotating the focus ring.
Adjust the projected image size
••
••
• Adjust the projected image size by moving the
zoom knob.
Select the ÒCOMPUTER 1Ó using the INPUT buttons on the projector or the COMPUTER 1 button on the remote control.
••
••
• When you press the INPUT buttons on the projector, the INPUT list appears.
Press
''
''
' /
""
""
" to select an item on the list, and press ENTER to switch to the selected INPUT mode.
••
••
• When using the remote control, press COMPUTER1 /2 , DVI , S-VIDEO or VIDEO to
switch the INPUT mode.
On the remote
control
On the
projector
""
""
" INPUT list
Press the STANDBY button, then press that button again while the confirmation message is displayed, to put the projector into standby mode.
••
••
• Even if you unplug the power cord from the AC outlet, the cooling fan continues to run for a while.
On the remote controlOn the projector
""
""
" On-screen Display
Adjust the projector angle
••
••
•
Adjust the projector angle using the Height
Adjustment buttons.
••
••
• Rotate the Tilt dial to adjust the horizontal tilt of
the projector.
Height Adjustment
buttons
Tilt dial
Focus ring Zoom knob
Zoom in
Zoom out
""
""
" On-screen Display (RGB)
RGB
1024 ◊ 768
COMPUTER1
INPUT
COMPUTER1
COMPUTER2
DVI-D Computer
D
Page 33
Downloaded From projector-manual.com Sharp Manuals
-23
Connections
Connecting to a Computer
Before connecting, ensure the power cord of the projector from the AC outlet is unplugged,
and that the devices to be connected are turned off. After making all connections, turn on the
projector and then the other devices. When connecting a computer, ensure that it is the last
device to be turned on after all the connections are made.
Esure he operaio mauals of he devices o be coeced have bee read before makig coecios.
When connecting with the RGB cable
(Coecig o COMPUTER/COMPONENT 1 or 2: The illusraio show below is for he former.)
To audio output terminal
To RGB output terminal
* ø3.5 mm stereo or mono audio cable
(commercially available or available as Sharp service part QCNWGA038WJPZ)
To COMPUTER/
COMPONENT 1
input terminal
Computer
To AUDIO input terminal
RGB cable
* Whe usig he ¿3.5 mm moo audio cable , he v olume le v el will be half of whe usig he ¿3.5 mm sereo audio cab le .
Noe
• See page 65 Compuer Compaibiliy Char for a lis of compuer sigals compaible wih he projecor.
Use wih compuer sigals oher ha hose lised may cause some of he fucios o o work.
• A Maciosh adapor may be required for use wih some Maciosh compuers. Coac your eares
Maciosh Dealer.
• Depending on the computer you are using, an image may not be projected unless the computerÕs
external output port is switched on. (e.g. Press ÒFnÓ and ÒF5Ó keys simultaneously when using a
SHARP notebook computer). Refer o he specific isrucios i your compuers operaio maual o
eable your compuers exeral oupu por.
RGB cable
Supplied
accessory
Downloaded From projector-manual.com Sharp Manuals
-25
Connections
Connecting to Video Equipment
The image qualiy is highes i order of he Compoe sigal, he RGB sigal, he S-video sigal ad he
Video sigal. If y our audio-visual equipme has a compoe oupu ermial or RGB oupu ermial, use he
COMPUTER/COMPONENT ermial 1 or 2 o he projecor for video coecio.
When connecting video equipment with a DVI output terminal
Noe
• Selec he ipu sigal ype of he video equipme. See page 47.
• While he projecor is coeced o video equipme ha has a HDMI oupu ermial, oly he video
sigal ca be ipu o he projecor. (Coec he AUDIO ipu ermial for audio ipu.)
• Depedig o specificaios of video equipme or HDMI o DVI digial cable, he sigal rasmissio
may o work propery. (The HDMI specificaio does o suppor all coecios o video equipme
ha has HDMI digial oupu ermial usig HDMI o DVI digial cable.)
• F or deails o compaibiliy for coecio, see suppor iformaio o DVI coecio provided by he
video equipme maufacurer.
When connecting video equipment with component video output terminal
(Coecig o COMPUTER/COMPONENT 1 or 2: The illusraio show below is for he former.)
Noe
• Whe you coec video equipme wih a 21-pi RGB oupu (Euro-scar) o he projecor, use a
commercially available cable ha fis i he projecor ermial you wa o coec.
• The projecor does o suppor RGBC sigals via he Euro-scar.
DVI Digital cable (commercially available)
To audio output terminals
ø3.5 mm stereo minijack to RCA audio cable
(commercially available)
To DVI output terminal
Video Equipment
To DVI-D
input terminal
To AUDIO input terminal
(for COMPUTER/COMPONENT 2, DVI-D)
To audio output terminal
ø3.5 mm minijack to RCA audio cable (commercially available)
3 RCA (Component) to 15-pin D-sub cable
(optional: AN-C3CP2)
To component video output terminal
To COMPUTER/COMPONENT 1
input terminal
To AUDIO
input terminal
Video Equipment
Downloaded From projector-manual.com Sharp Manuals
-41
Useful Features
ÒScreen adjustment (SCR-ADJ)Ó menu
O
Off
O
Off
Main Menu Sub Menu
OSD Display
Backgroud
Logo
Blue
Noe
Normal
Full
Do By Do
Area Zoom
V-Srech
Srech
Ceer
Upper Righ
Lower Righ
Upper Lef
Lower Lef
Meu Posiio
Page 50
Resize
Page 49
Page 50
Page 50
Auo V-Keysoe
Page 49
Page 49
Page 49
+40-40
Image Shif
V-Keysoe
Page 49
+100-100
H-Keysoe
SCR-ADJ
Page 49
Laguage
Page 50
Fro
Ceilig + Fro
Rear
Ceilig + Rear
PRJ Mode
Page 50
Eglish
Deusch
Espaol
Nederlads
Fraais
Ialiao
Sveska
Porugus
polski
Magyar
Trke
+60-60
ÒSignal adjustment (SIG-ADJ)Ó menu
O
Off
SIG-ADJ
+30-30
+60-60
+150-150
+150-150
Clock
Phase
H-Pos
V-Pos
Rese
Sigal Ifo
Resoluio
Main Menu
Auo Syc
Page 47
Page 47
Page 47
Page 47
Page 48
*4
*4
*5
*5
*5
Sigal Type
Page 47
Page 48
*6
Auo
RGB
Compoe
Dyamic Rage
*7
Auo
Sadard
Ehaced
Auo
PAL
SECAM
NTSC4.43
NTSC3.58
PAL-M
PAL-N
PAL-60
Video Sysem
Page 48
*8
*4 Item when inputting RGB signal through COMPUTER/COMPONENT 1 or 2
*5 Item when inputting COMPUTER/COMPONENT 1 or 2
*6 Item when selecting COMPUTER/COMPONENT 1, 2 or DVI-D
*7 Item when selecting DVI-D
*8 Item when selecting VIDEO or S-VIDEO
Downloaded From projector-manual.com Sharp Manuals
-47
Useful Features
0
0
0
0
Phase
Clock
Pic. SIG
—
ADJ SCR PRJ Ne.
H-Pos
V-Pos
Rese
Auo
640 x 480
O
Sadard
Auo
SEL./ADJ.
RETURN
ENTER
END
Resoluio
Auo Syc
Sigal Type
Dyamic Rage
Video Sysem
Sigal Ifo : 800 x 600
H 60.3 kHz / V 37.8 Hz
1
3
4
5
6
2
7
Signal Adjustment (ÒSIG-ADJÓ Menu)
11
11
1
Adjusting the Computer Image
If the optimum image cannot be obtained with Auto
Sync adjustment, use the SIG-ADJ function.
Note
• To reset all adjustment items, select “Reset” and
press ENTER.
• The adjustable range of “H-Pos” (H-Position)
and “V-Pos” (V-Position) may vary depending
on the screen resolution of the computer.
Selectable items
Clock
Phase
H-Pos
V-Pos
Description
Adjusts vertical noise.
Adjusts horizontal noise (similar to
tracking on your VCR).
Centers the on-screen image by
moving it to the left or right.
Centers the on-screen image by
moving it up or down.
22
22
2
Resolution Setting
Ordinarily, the type of input signal is detected and the
correct resolution mode is automatically selected. How-
ever, for some signals, the optimal resolution mode in
Ò ResolutionÓ on the Ò SIG-ADJÓ menu may need to be
selected to match the computer display mode.
Note
• See “Checking the Input Signal” on page 48 for
information on the currently selected input sig-
nal.
33
33
3
Auto Sync Adjustment
Used to automatically adjust a computer image.
Note
• Auto Sync adjustment is also performed by
pressing AUTO SYNC on the projector or on
the remote control.
• The Auto Sync adjustment may take some time
to complete, depending on the image of the
computer connected to the projector.
Selectable items
On
Off
Description
Auto Sync adjustment will occur when
the projector is turned on or when the
input signals are switched, when
connected to a computer.
Auto Sync adjustment is not automati-
cally performed.
Menu operation
Page 43
44
44
4
Signal Type Setting
This function allows you to select the input sig-
nal type RGB or Component for COMPUTER/
COMPONENT 1, 2 or DVI-D.
Description
Input signals are automatically recog-
nized as RGB or component.
Set when RGB signals are received.
Set when Component signals are
received.
Selectable items
Auto
RGB
Component
Downloaded From projector-manual.com Sharp Manuals
-49
Useful Features
Resize
0
0
0
Image Shif
H-Keysoe
V-Keysoe
Auo V-Keysoe
Ceer
O
O
Normal
Logo
Fro
Eglish
SEL./ADJ.
RETURN
ENTER
END
OSD Display
Backgroud
Meu Posiio
PRJ Mode
Laguage
Pic. SIG SCR-ADJ PRJ Ne.
1
3
4
5
6
7
8
2
Screen Adjustment (ÒSCR-ADJÓ Menu)
Menu operation
Page 43
11
11
1
Setting the Resize Mode
Note
• For details of the Resize mode, see pages 37
and 38.
• You can also press RESIZE on the remote con-
trol to set the resize mode. (See page 37.)
22
22
2
Adjusting the Image Position
You can move the projected image vertically.
Note
• This function only works in some RESIZE
modes. (See pages 37 and 38.)
• To reset this function, select “0”.
button
button
33
33
3
Keystone Correction
When the image is projected either from the top or from
the bottom towards the screen at an angle, the image be-
comes distorted trapezoidally. The function for correct-
ing trapezoidal distortion is called Keystone Correction.
Auto V-Keystone Correction
Set ÒAuto V-KeystoneÓ on the ÒSCR-ADJÓ screen
menu to ÒOnÓ.
Manual Keystone Correction
Set ÒAuto V-KeystoneÓ on the ÒSCR-ADJÓ screen
menu to ÒOffÓ. Select ÒV-KeystoneÓ, and then
press or to parallelize the left and right sides
of the projected image with the slide bar. To
parallelize the upper and lower sides, select ÒH-
KeystoneÓ and press or .
Note
• The Keystone Correction can be adjusted up to
an angle of approximately ±12 degrees with “Auto
V- Keystone” and up to an angle of approximately
±50 degrees with “V-Keystone” and approxi-
mately ±30 degrees with “H-Keystone”.
• When the screen is slanting or the image is de-
teriorated, set “Auto V-Keystone” to “Off”.
Horizontal Keystone Correction
Vertical Keystone Correction
Downloaded From projector-manual.com Sharp Manuals
-51
Useful Features
Auo Power Off
Auo Resar
Sysem Soud
Speaker
Audio Ou
9600bps
Eable
O
O
O
FAO
O
Eable
Normal
Disable
SEL./ADJ.
RETURN
ENTER
END
Moior Ou
LAN/RS232C
RS-232C
Fa Mode
Sysem Lock
All rese
Lamp Timer (Life) [ 0]h [ 0] mi ( 100%)
Pic. SIG SCR PRJ-ADJ Ne.
1
2
3
4
5
6
7
8
9
0
q
w
Menu operation
Page 43
Description
The projector automatically enters the
standby mode when no input signal is
detected for 15 minutes or longer.
The Auto Power Off function will be
disabled.
Selectable items
On
Off
11
11
1
Auto Power Off Function
Note
• When the Auto Power Off function is set to ÒOnÓ,
5 minutes before the projector enters the
standby mode, the message ÒEnter STANDBY
mode in X min.Ó will appear on the screen to
indicate the remaining minutes.
Description
If the power cord is unplugged from the
outlet or the breaker switch is turned off
when the projector is on, then the
projector automatically turns on when
the power cord is plugged into the AC
outlet or the breaker switch is turned on.
The projector does not turn on auto-
matically when the power cord is
plugged into the AC outlet or the
breaker switch is turned on.
Selectable items
On
Off
22
22
2 Auto Restart Function
Description
A confirmation sound is made when the
projector turns on/off.
No confirmation sound is made.
Selectable items
On
Off
33
33
3
Setting the Confirmation
Sound (System Sound)
Helpful Functions Set during Installation (ÒPRJ-ADJ Ó menu)
44
44
4
Speaker Setting
This function allows you to set the audio output
of the internal speaker to ÒOnÓ or ÒOffÓ such as
when the projector is connected to an external
amplifier.
Selectable items
On
Off
Description
The audio signal is output from the internal
speaker.
The audio signal is not output from the
internal speaker.
55
55
5
Audio Output Type Setting
This function determines whether the audio level
output from the AUDIO output (MONITOR output)
terminal is fixed or variable by linking with VOL-
UME.
Info
• When ÒAudio OutÓ has been set to ÒVAOÓ, first make
sure to lower the volume of the projector before
turning the power on or off and when switching the
input.
Description
Audio output that does not vary in
strength with the volume level of the
source projector.
Audio output that varies in strength with
the volume level of the source projector.
Selectable items
FAO
(Fixed Audio
Output)
VAO
(Variable
Audio Output)
66
66
6
Monitor Output
77
77
7
LAN/RS232C
When set to ÒEnableÓ, the function is activated
and power is consumed even in the standby mode.
It is recommended that the function be set to ÒDis-
ableÓ when it is not connected. This reduces power
consumption when the projector is in the standby
mode.
Description
The function is activated even if the
projector is in standby mode.
The function is switched off when the
projector is in standby mode.
Selectable items
Enable
Disable
Note
• When you want to control the projector using
the LAN/RS232C function, select ÒEnableÓ.
Downloaded From projector-manual.com Sharp Manuals
-53
Useful Features
Menu operation
Page 43
5 Enter the same keycode in ÒRe-con-
firmÓ.
Noe
To cancel the keycode that you have al-
ready set
• Press " o he projecor for four imes i seps
4 ad 5 above.
When the System Lock is set
• Whe Sysem Lock is se, he keycode ipu scree
appears afer he power is ured o. Whe i ap-
pears, eer he righ keycode o sar projecio.
Input screen for keycode
Info
• Keylock cao be se while he projecor is: dis-
playig he Meu screes, i sadby mode,
warmig up, chagig ipu sigals, operaig
Auo Syc fucio or o he Sysem Lock
scree durig warmig up.
Sysem Lock
————
Keylock Function
Locking the Operation Buttons on
the Projector
Use this function to lock the operation but-
tons on the projector.
 Locking the Operation Buttons
Hold down ENTER on the projector for about 5 sec-
onds while the projector is being turned on.
 On-screen Display
Keylock function ON
• The keylock fucio does o affec he operaio
wih he remoe corol buos.
• Y ou cao use he keylock fucio while he pro-
jecor is warmig up.
 Taking the Keylock off
Hold down ENTER on the projector for about 5 seconds.
 On-screen Display
Keylock function OFF
• Whe he projecor is i sadby mode, you ca
release he keylock by holdig dow ENTER ad
STANDBY/ON o he projecor simulaeously for
abou 5 secods.
Returning to the Default
Settings
This function allows you to initialize the settings
you have made in the projector.
Noe
The followig iems or meu cao be iiialized.
• SIG-ADJ meu
Resoluio
• SCR-ADJ meu
Laguage
• PRJ-ADJ meu
Lamp Timer (Life)
Sysem Lock
Checking the Lamp Life
Status
You can confirm the cumulative lamp usage time
and the remaining lamp life (percentage).
Noe
• I is recommeded ha he lamp be chaged
whe he remaiig lamp life becomes 5%.
• Remaiig lamp life chages wihi he rage
of he values sho w depedig o he frequecy
a which Eco+Quie Mode is swiched o O
ad Off. (See page 46.)
• The lamp life may vary depedig o he us-
age codiio.
L amp usage codiio
Life
Operaed exclusively
while Eco+Quie Mode
is O.
Operaed exclusively
while Eco+Quie Mode
is Off.
Remaiig lamp life
100% 5%
Approx. Approx.
3,000 hours 150 hours
Approx. Approx.
2,000 hours 100 hours
Downloaded From projector-manual.com Sharp Manuals
-63
Appendix
User service screw
(for lamp ui cover)
AC socket
5 Insert the new lamp unit.
• Press the lamp unit firmly into the lamp
unit compartment. Fasten the securing
screws.
6 Replace the lamp unit cover.
• Align the lamp unit cover and slide it to
close. Then tighten the user service
screw to secure the lamp unit cover.
Info
• If the lamp unit and lamp unit cover are not
correctly installed, the power will not turn
on, even if the power cord is connected to
the projector.
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
Info
• Make sure to reset the lamp timer only
when replacing the lamp. If you reset the
lamp timer and continue to use the same
lamp, this may cause the lamp to become
damaged or explode.
• You can also reset the lamp timer via the
LAN.
(Refer to the SETUP MANUAL on the sup-
plied CD-ROM for details.)
1 Connect the power cord.
• Plug the power cord into the AC socket
of the projector.
2 Reset the lamp timer.
• While simultaneously holding down " ,
ENTER and MENU on the projector,
press STANDBY/ON on the projector and
keep all four buttons pressed down until
the lamp indicator starts blinking green.
• “LAMP 0000H” is displayed, indicating
that the lamp timer is reset.
" button
ENTER button
STANDBY/ON button
Lamp indicator
MENU button
Downloaded From projector-manual.com Sharp Manuals
-65
Appendix
Noe
• This projecor may o be able o display images from oebook compuers i simulaeous (CRT/LCD)
mode. Should his occur, ur off he LCD display o he oebook compuer ad oupu he display daa
i CRT oly mode. Deails o how o chage display modes ca be foud i your oebook compuers
operaio maual.
• Whe his projecor receives 640 × 350 VESA forma VGA sigals, 640 × 400 appears o he scree.
• Whe projecig he RGB ierlace sigal usig COMPUTER/COMPONENT 1, 2 or D VI-D wih Sigal Type
se o Auo or RGB, he image may o be projeced as desired. I his case, use eiher Video or S-Video.
• Depedig o he compuer you are usig, he oupu sigal may o be faihful o he Scree resoluio
adjusme. Chec k he seigs of he compuer s sigal oupu. If he seigs cao be chaged, i is recom-
meded ha he resoluio be se o he oe ha correspods o  1280 × 800.
Computer Compatibility Chart
• Muliple sigal suppor
Horizoal Frequecy: 15—110 kHz
Ve r ical Frequecy: 43—85 Hz
DTV
Computer
Pixel Clock: 12—170 MHz
Syc sigal: Compaible wih TTL level
• Compaible wih syc o gree sigal














Mode Resolution VESA
Vertical Frequency
(Hz)
Analog RGB
Support
Digital RGB
Support
Horizontal Frequency
(kHz)
VGA
SVGA
XGA
WXGA
SXGA
SXGA+
UXGA
MAC 13"
MAC 16"
MAC 19"
MAC 21"
640 ◊ 350
640 ◊ 400
720 ◊ 350
720 ◊ 400
640 ◊ 480
800 ◊ 600
1024 ◊ 768
1280 ◊ 720
1280 ◊ 768
1280 ◊ 800
1360 ◊ 768
1366 ◊ 768
1152 ◊ 864
1280 ◊ 1024
1400 ◊ 1050
1600 ◊ 1200
640 ◊ 480
832 ◊ 624
1024 ◊ 768
1152 ◊ 870
27.0
31.5
37.9
27.0
31.5
37.9
27.0
31.5
27.0
31.5
37.9
26.2
31.5
34.7
37.9
37.5
43.3
31.3
35.2
37.9
46.6
48.1
46.9
53.7
40.3
48.4
56.5
60.0
68.7
45.0
47.8
49.7
62.8
47.7
47.8
55.0
66.2
67.5
64.0
80.0
64.0
65.3
75.0
34.9
49.7
60.2
68.7
60
70
85
60
70
85
60
70
60
70
85
50
60
70
72
75
85
50
56
60
70
72
75
85
50
60
70
75
85
60
60
60
75
60
60
60
70
75
60
75
60
60
60
67
75
75
75
15.7
31.5
33.8
15.6
31.3
37.5
45.0
28.1
33.8
56.3
67.5
480
480P
540P
576
576P
720P
720P
1080
1080
1080P
1080P
60
60
60
50
50
50
60
50
60
50
60
Signal Vertical Frequency (Hz) DVI SupportHorizontal Frequency (kHz)








The following is a list of modes that conform to VESA. However, this projector supports other signals
that are not VESA standards.
Downloaded From projector-manual.com Sharp Manuals
-67
Appendix
CheckProblem P age
A uusual soud is
occasioally heard
from he cabie.
Maieace
idicaor illumiaes or
b liks i red.
The projecor cao be
ured o or pu io he
sadby mode usig he
STANDBY/ON buo o
he projecor.
Picure is gree wih
compoe ipu sigals
(COMPUTER/
COMPONENT 1, 2, DVI-D) .
Picure is pik (o gree)
wih RGB ipu sigals
(COMPUTER/
COMPONENT 1, 2, DVI-D) .
Picure is oo brigh ad
whiish.
The black levels of he
image show badig or
appear faded whe DVI-
D is seleced.
The coolig fa
becomes oisy.
The lamp does o ligh
up eve afer he
projecor urs o.
The lamp suddely urs
off durig projecio.
The image someimes
flickers.
The lamp akes a log
ime o ur o.
Picure is dark.
The remoe corol
cao be used.
• If he picure is ormal, he soud is due o cabie shrikage
caused by room emperaure chages. This will o affec
operaio or performace.
• See Maieace Idicaors.
• The keylock is se.
If he keylock is se o ON, all he buos are locked.
• Chage he ipu sigal ype seig.
• Image adjusmes are icorrecly se.
• Selec he Dyamic Rage seig (Sadard or Ehaced)
ha resuls i he bes picure qualiy.
• Whe emperaure iside he projecor icreases, he coolig
f a r us faser.
• The lamp idicaor is illumiaig i red.
Replace he lamp.
• Cables icorrecly coeced o he projecor or he coeced
equipme works improperly.
• If his happes frequely, replace he lamp.
• The lamp will eveually eed o be chaged.
The lamp has reached he ed of is life. Replace he lamp.
• Operae he remoe corol while poiig i a he projecors
remoe corol sesor.
• The remoe corol may be oo far away from he projecor.
• If direc suligh or a srog fluoresce ligh is shiig o he
projecors remoe corol sesor, place he projecor where i
will o be affeced by srog ligh.
• The baeries may be depleed or isered icorrecly. Make
sure he baeries are isered correcly or iser ew oes.

59
53
47
45
48

59
23-29
62
62
15
15
This projecor is equipped wih a microprocessor. Is performace could be adversely affeced by
icorrec operaio or ierferece. If his should happe, uplug he projecor ad plug i i agai
afer more ha 5 miues.
Downloaded From projector-manual.com Sharp Manuals
-69
Appendix
Specifications
As a par of policy of coiuous improveme, SHARP reser ves he righ o make desig
ad specificaio chages for produc improveme wihou prior oice. The performace
specificaio figures idicaed are omial values of producio uis. There may be some
deviaios from hese values i idividual uis.
Model
Display devices
Resolution
Lens
Input terminals
Output terminals
Control and
communication
terminals
Speakers
Projection lamp
Rated voltage
Rated frequency
Input current
Power consumption (Standby)
Operation temperature
Cabinet
Dimensions (main body only) [W × H × D]
Weight (approx.)
F number
Zoom
Focus
DVI-D (Compatible with HDCP)
Computer/Component
(mini D-sub 15 pin)
S-Video (mini DIN 4 pin)
Video (RCA)
Audio (ø3.5 mm stereo minijack)
Audio (RCA)
Computer/Component
(mini D-sub 15 pin)
Audio (ø3.5 mm stereo minijack)
LAN (RJ-45)
USB (Type B)
RS-232C (mini DIN 9 pin)
Wired Remote
(ø3.5 mm stereo minijack)
XG-C455W/PG-C355W
0.74" LCD panel × 3
WXGA (1280 × 800)
F 1.7 – 1.9
Manual, × 1.2 (f = 28.0 – 33.6 mm)
Manual
× 1
× 2
× 1
× 1
× 2
× 2 (L/R)
× 1
× 1 (variable audio output)
× 1
× 1
× 1
× 1
2 W (Mono)
275 W
AC 100 – 240 V
50/60 Hz
3.6 A
360 W (3.4 W) with AC 100 V
345 W (4.4 W) with AC 240 V
41° F to 95° F (+5° C to +35° C)
Plastic
12
27
/ 32 " × 4" × 11
1
/ 64 "
(326 × 101.5 × 279.5 mm)
10.8 lbs. (4.9 kg)
Downloaded From projector-manual.com Sharp Manuals