HF COLOR VIDEO INTERCOM WITH RECORDING HFX-700R KIT , OWNER S MANUAL INSTALLATION AND OPERATION
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS WARNING FCC CLASS B NOTICE HFX-700R KIT VIDEO INTERCOM SYSTEM 1.HFX-700R KIT Introduction 2.HFX-700R KIT Parts Identification 2.1.Main Monitor 2.2.Door Camera 2.3.HFX-700R KIT Packaging 3.HFX-700R KIT Installation 3.1. Positioning the devices 3.2. Installation 3.3. Door Release Options 4. HFX-700R KIT read before operation 4.1. Attention 4.2. On screen menu icons 4.3. Setup menu 4.3.1. Adjust clock 4.3.2. Door open status indication 4.3.3.
IMPORTANT SAFETY INSTRUCTIONS WARNING: TO RE DUCE TH E RISK OF FIRE OR E LECTRIC SHOCK , DO NOT E XPOSE THE MONITOR OR POW ER ADAP TER TO WATE R OR MOIST URE . Read Instructions -All the safety and operating instructions should be read before operating this equipment. These instructions should be retained for future reference. Heed Warnings - All warnings on the equipment and in the operating instructions should be adhered to.
WARNING WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THE MONITOR OR POWER ADAPTER TO WATER OR MOISTURE. CAUTION: DO NOT OPEN. RISK OF ELECTRICAL SHOCK. CAUTION! TO REDUCE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER OR BACK, NO USER SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. OTH ER WARNINGS Monitor is designed for indoor use only. Do not install outdoors. Keep the equipment dry. If water should get in,wipe off immediately.
FCC CLASS B NOTICE NOTE: This equipment has been Certified and found to comply with the limits regulated by FCC,and CE. Therefore, it is designed to provide reasonable protection against interference and will not cause interference with other appliance usage. However, it is imperative that the user follows this manuals guidelines to avoid improper usage which may result in damage to the unit, electrical shock, and fire hazard or injury.
HFX-700R KIT VIDEO INTERCOM SYSTEM 1. HFX-700R KIT introduction Thank you for purchasing this Video Intercom System. This advanced system not only allows you to identify and communicate with visitors at the door and allows for remote door strike release, it can also record the video intercom communication on a micro SD card for later playback. This system has an interactive on screen menu for easy operation by touch sensitive buttons located on the two sides of the screen.
2.HFX-700R KIT Parts Identification 2.1. Main Monitor 1 2 3 178mm (7.0 ) 15 14 4 7 8 36mm (1.42 ) 6 16 5 9 10 11 12 13 118mm (4.65 ) HFX-700R Main monitor identification: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. Micro SD card slot socket 3.
HFX-700R Main menu identification: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 1 2 4 3 5 6 7 8 9 10 Confirm Video and menu display area Tab right Tab left Play Setup 1st doorbell camera 2st doorbell camera Paging other monitor Chime enable or disable Main monitor w all mount bracket Wall mount bracket Wiring terminals 1 PT1 2 DG1 3 OUT+ PT 1 PT 2 136mm (5.35 ") DG1 DG2 OUT + PT2 DG2 OUTDR2 DR1 <+> POWER <-> 89mm (3.5 ") OUT- 4 DR2 5 DR1 6 <+> POWER <-> 8.4mm(0.
2.2. Door Camera 1 7 3 4 130mm (5.12") JP2 1 2 5 2 10 JP1 9 8 3 4 11 6 36mm (1.42") 98mm (3.86") HFX-700R Door Camera identification: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. White LED Illumination Speaker 1/3" Color CCD Microphone Call button Screw cover CCD view angle knob (-6 degrees, 0 degrees, 8 degrees, 16 degrees) Jumper 2 (enable/disable light senor) Jumper 1 (dry contact or current output selection) Wire to door strike Wire to main Monitor 2.3.
3. HFX-700R KIT Installation 3.1. Positioning the devices Main monitor Proper height: Door camera View Angle: 70cm (27.6") 170cm (66.9") 100cm (39.3") 165cm (64.9") 50cm(19.7 ") 50cm(19.7 ") The proper height of monitor or door camera is 160~170cm(63"~67") from the ground. This may vary on each installation. View range should be actively tested before complete. Viewing window of door camera is about 70cm up-n-down, and 100cm left-n-right.
3.2. Installation STAGE 1: Installation of main monitor A. Fasten the wall mount bracket using the provided hardware. B. Fasten wires on terminals accordingly. (Refer to STAGE 3) C. Plug pin wires and mount the monitor unit on bracket. Monitor Wall mount bracket Do not plug pow er at this stage. STAGE 2: Installation of the door cameras A. Use security screw wrench disassemble screw and remove door camera unit from bracket. B. Fasten wall mount bracket on position. C.
STAGE 3: Wiring and settings A. Wire the system from door camera terminals to monitor terminals accordingly. B. Select and plug JP2 to its RIGHT( ) to disable LED illumination of the doorbell camera when it's activated. Factory setting is LEFT( ) which enables automatic LED illumination. C. Select and plug JP1 to its RIGHT( ) for direct current output control (12VDC 300mA) directly for a strike. Factory setting has JP1 to its LEFT ( ) for dry contact bridge control.(Refer to 3.3 Door Release Options) D.
3.3. Door Release Options Each Door Camera on the system is able to operate and release one electric lock. On a full system with 2 door cameras, the user is able to release up to two electric locks. The system can only release one electric lock at a time, depending on which door camera the call originated from. There are two door release wiring options that work with the Video Intercom System.
4. HFX-700R KIT read before operation 4.1. Attention A. Micro SD card, SDHC(High Capacity SD card), is not included in this product package. B. Insert SD card properly. The SD card can be 2GB to 16GB memory size. HC 4 i cro mS SD card socket C. The video quality is 720x480 pixels, every recording (20 sec. a section) takes about 15M memory size. Every photo takes about 130KB memory size (So for a 4 GB card, it can hold about 260 Videos or 25,000 pictures). D.
4.3. Setup menu A. Move cursor to SETUP icon at main menu; B. Press can enter setup menu. 4.3.1. Adjust clock A. At setup menu, and can move the cursor; can alter parameter (figure 1); B. can save your new setup. and 4.3.2. Door open status indication A. There are PT1 and PT2 terminals on main monitor for connection of a magnetic switch to detect door open status. (magnetic switch is not included in the package) B.
4.3.3 Video or photo recording A. At setup menu, and can move the cursor to the mode you like; can save your setup. B. If select , enable automatic video recording mode, 20 seconds a section, when visitor calls from doorbell camera. C. If select , enable automatic photo recording mode, 3 shots per action, when visitor calls from doorbell camera. Video 15:30 Photo 3 15:30 V3.0.2(101206) V3.0.2(101206) (figure 1) (figure 2) 4.3.4. Format a new SD card A.
4.4. Intercom function operations 4.4.1. Push to talk function A. Speach open LED on means voice is free to go out from monitor to door camera. B. During conversation, press Monitor Button for 2 seconds to switch to push to talk mode. Under this mode, press-on Monitor Button and speaking out LED on allows push to talk to go out to door camera; let-go Monitor Button and speaking out LED off allows unilateral voice to come in from door camera. C.
4.4.3. zoom and pan/tilt function A. While talking to the doorbell camera from main monitor, tenant can at the same time operate the on-screen-menu to stop or resume video recording. B. To operate zoom and pan/tilt function has to stop recording first and resume afterward. (figure 1,2,3,4) REC 0 0 0 0 12 2010/06/28 04 57 39 SD X (figure 1:stop recording) SD 2010/06/28 04 5 7 39 X (figure 3 1 (figure 2 :resume recording) 2010/06/28 04 5 7 39 SD 3 X zoom) 3 (figure 4: pan/tilt) 4.4.4.
4.4.5. All page announcement and intercom among monitors A. From any monitor, tenant can press intercom button or select the function from the on-screen main monitor menu to page and make a nnoucements to other monitors (figure 2). B. Paging and annoucements can last for 30 seconds time, if any other monitor press the intercom button to respond, the two monitors can then engage in intercom conversation for maximum of 90 seconds. SD 2010/06/28 04 5 7 39 (figure 1) (figure 2) 4.5. Privacy function A.
10062800 /100401-1 1 01224 00 10/06/28 04 57 39 (figure 1) (figure 2) 2010/06/28 04 5 7 3 9 1 0 / 1 2/ 0 8 04 57 39 10120800 /1 1 2 6 5 5 - 1 (figure 3) (figure 4) 4.6.2. Delete video/photo section(s) A. Select to enter delete sub menu. (figure 5). B. Move and select delete by SINGLE video section or ALL video sections. C. Reconfirm YES or NO for the action (figure 6). D. Select EXIT to move to PLAYBACK menu; Select to return to main menu.
EXPANSION OPTIONS A. HFX-700R package consists of a main monitor, a door camera, and a power adaptor for the monitor. B. With HFX-700R basic system fully expanded, the system is capable of expanding up to a total of 4 indoor monitors and 2 doorbell cameras. System layout 1: NOTE: the system is capable of expanding up to a total of 4 monitors (1 main video monitor + 3 expansion video monitor or 3 expansion audio monitor (video or audio mixing types) and 2 door cameras.
System layout 2: NOTE 1: The wiring HUB can amplify and distribute the 2-wire signal among the main monitor and sub-monitors. NOTE 2: the system is capable of expanding up to a total of 5 monitors with 1 EX-HUB or 8 total monitors with 2 EX-HUBs connected in one system.
A Max A Max HFX-700R EX-700D EX-700H or EX-700A B Max C Max EX-HUB OUT1 IN OUT2 POWER OUT3 POWER LED OUT4 EX-700H or EX-700A NOT E 1:OUT4 can also be used to connect to a expansion monitor. NOT E 2:wiring distance<300ft.
1. Expansion Video Monitor (EX-700H) 1.1. EX-700H Identification EX-700H 13 1 178mm (7.0 ) 15 12 2 5 6 36mm (1.42 ) 4 3 7 8 9 10 11 118mm (4.65 ) EX-700H identification: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 14 3.
EX-700H Wall mount bracket Wiring terminals Wall mount bracket 1 PT1 2 OUT+ 3 IN+ PT1 PT2 PT2 136mm (5.35 ) OUT+ OUTIN+ IN- <+> POWER <-> 4 89mm (3.5 ) OUT- IN- <+> POWER <-> 8.4mm(0.
1.2. EX-700H Installation STAGE 1: Installation of the expansion monitor A. Fasten the wall mount bracket using the provided hardware. B. Fasten wires on terminals accordingly. (Refer to STAGE 2) C. Plug pin wires and mount the monitor unit on bracket. Monitor Wall mount bracket Do not plug pow er at this stage. STAGE 2: Wiring and settings A. Wire the system from terminals to terminals as accordingly.
1.3. EX-700H Operation 1.3.1. Visitor Calls from Door Camera A. When the Call button on the camera is pressed, All monitors on the system will ring with a chime sound and all monitors will be activated. B. After the call, if nothing on the monitor is pressed, the system will time out after 30 seconds. If the monitor button is pressed, the system will stay active for 90 seconds. C. You are able to terminate the activity on the monitor at any time by pressing the Cut-off button . D.
2. Expansion audio Monitor (EX-700A) 2.1. EX-700A Identification 178mm (7.0 ) 12 11 1 4 5 36mm (1.42 ) 3 2 6 7 8 9 118mm (4.65 ) EX-700A identification: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13.
EX-700A Wall mount bracket Wiring terminals Wall mount bracket 1 PT1 2 OUT+ 3 IN+ PT1 PT2 PT2 136mm (5.35 ) OUT+ OUTIN+ IN- <+> POWER <-> 4 89mm (3.5 ) OUT- IN- <+> POWER <-> 8.4mm(0.
2.2. EX-700A Installation STAGE 1: Installation of the expansion monitor A. Fasten the wall mount bracket using the provided hardware. B. Fasten wires on terminals accordingly. (Refer to STAGE 2) C. Plug pin wires and mount the monitor unit on bracket. Monitor Wall mount bracket Do not plug pow er at this stage. STAGE 2: Wiring and settings A. Wire the system from terminals to terminals as accordingly.
2.3. EX-700A Operation A. Operates the same as EX-700H (Refer to page 25). B. EX-700A audio only function, no video function. 2.3.1. All-page and intercom function A. When system consists of main monitor and expansion audio monitor and an outdoor doorbell/camera unit, the system can provide intercom function. B. Press intercom button from any monitor, all other monitors will react by making bell sound. At the same time, the host can speak and broadcast voice message to all other monitors. C.
3. Door Camera (EX-700D) 3.1. EX-700D Identification 1 7 2 3 130mm (5.12" ) JP2 1 4 5 2 10 JP1 9 8 3 4 11 6 36mm (1.42" ) 98mm (3.86" ) EX-700D identification: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11.
3.2. EX-700D Installation STAGE 1: Installation of the door camera A. Use security screw wrench disassemble screw and remove door camera unit from bracket. B. Fasten wall mount bracket on position. C. Fasten wires on terminals and select jumpers for desired function. (refer to STAGE 2) D. Mount door camera unit on bracket, secure the assembly screw. Security screws wrench Pull out screw cover to access the screw Door camera Bracket STAGE 2: Wiring and settings A.
4. Metal Door Camera Housing (EX-700V) 4.1. EX-700V contents EX-700V is an optional housing assembly kit to enclose EX-700D to become flush mount metal doorbell camera. x1 x1 x1 Front panel Bracket 1 Rubber seal x4 4.5 x10mm Screw x6 3.0 x6mm Screw x1 x1 Bracket 2 x1 Embed box Screw wrench Depends on different wall materials, please refer to the cut open size for EX-700V. Measurements Unit:mm Unit:inch 100x150x41 3.94"x5.91"x1.
4.3. Assembly Procedure STEP 1-1 : A. If on wooden wall, cut open space is 100x150x41mm. B. Embed box may not necessary. Go to Step 2. STEP 1-2 : A. If on cement or brick wall, cut open a hole size of 114x165x49mm. B. Make sure the stamp wire outlet on embed box been pried open. C. Insert and secure embed box inside the hole. STEP 2 : A. Install bracket 2 on top of the embed box. B. If without embed box, fasten bracket 2 directly on the wooden wall. STEP 3 : A. Install bracket 1 on top of bracket 2.
TECHNICAL SPECIFICATIONS HFX-700R(main monitor) 3.5" digital TFT-LCD 320 x 240 pixels 30 seconds time out; 90 seconds for conversation 30 seconds time out; Auto Timer (intercom): 90 seconds for conversation Operating Temperature: 14 ~ 140 , indoor Dimensions (w/ bracket): 4.65"(L) x 7.0"(W) x 1.42"(D) input 100~240VAC 50/60Hz; Power adaptor: output 23VDC/1A(24W), external standby 3.5W, operating 11.
EX-700H(optional expansion monitor) 3.5" digital TFT-LCD 320 x 240 pixels 30 seconds time out; 90 seconds for conversation 30 seconds time out; Auto Timer (intercom): 90 seconds for conversation Operating Temperature: 14 ~ 140 , indoor Dimensions (w/ bracket): 4.65"(L) x 7.0"(W) x 1.42"(D) input 100~240VAC 50/60Hz; Power adaptor: output 23VDC/1A(24W), external standby 1.4W, operating 3.
TROUBLE SHOOTING Before requesting service, check the troubleshooting quide to solve the problem. Problem Solution No power (no picture on monitor) Make sure AC plug is firmly inserted into the AC outlet. Make sure the power terminal is firmly connected into the monitor unit. Check to ensure polarity is correct. (Red=positive, Black=negative). System is on but no picture on the monitor Make sure the cable is cnnected securely between the master monitor and the camera.
SERVICE AND WARRANTY To receive after sales service, please provide the follow ing information when contact. a. Name of the product b. Model and serial number of the product c. The store, s name where you purchased d. Date purchased e. Idea and area of possible problems Information Card Product name Model and serial number , The store s name Date purchased (receipt) The w arranty statements a. This product is produced under strict internal quality control and inspection procedures. b.
http:// w w w .comelitusa.com Info@comelitusa.
