VL-NZ50E/hyou; 02/2/21/18:00 VL-NZ50E OPERATION MANUAL OPERATION MANUAL ENGLISH VL-NZ50E VL-NZ50E LIQUID CRYSTAL DISPLAY CAMCORDER
Before using the camcorder, please read this operation manual carefully, especially page iv. OPERATION MANUAL WARNING TO PREVENT SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. ENGLISH CAUTION To prevent shock, do not open the cabinet. No user serviceable parts inside. Refer servicing to qualified dealer or service centre. This equipment should be used with the recommended AC adapter or battery pack. CAUTION To prevent electric shocks and fire hazards, do NOT use any other power source.
Information for Australia/New Zealand Only This Camcorder must be supplied only with DC 7.4 volts from a BT-L225 or BTL445 battery or the AC adapter (UADP-0342TAZZ). CAUTION: As there are no user-serviceable parts inside the Camcorder or AC adapter, do NOT remove their cabinets as touching parts inside could result in electric shock. Please refer servicing to a qualified dealer or a Camcorder service centre approved by Sharp. NOTE This Camcorder is a high technology product.
Quick Operation Guide Please consult this operation manual further for details on these and other functions of your camcorder. Attaching the Battery Pack Power switch Charging the Battery Pack 1 Attach the battery pack on the camcorder, and make sure that the Power switch is set to OFF. 2 Connect the supplied power cord to the AC power socket on the AC adapter, and insert the AC plug into a power outlet. AC power socket 1 To power outlet Make sure that the Power switch is set to OFF.
Inserting a Cassette 1 Attach the power source to the camcorder, then slide the cassette compartment door release and open the cassette compartment door. • After confirmation sound, the cassette holder extends and opens automatically. Cassette compartment door release Tips on Recording Positions To create images that are easy to watch during playback, try to record with an upright posture and steady hand to prevent a shaky image.
Quick Operation Guide REC START/STOP button Power Zoom control/Volume control Zooming Push the Power Zoom control to T (1) (telephoto) or W (2) (wide angle) side. Power Zoom control Playback Operation button Power switch 1 Easy Camera Recording 1 2 Insert a cassette into the camcorder. Hold down the Lock button and set the Power switch to CAMERA. Lock button 2 Press j (or k) on the Operation button to rewind (or fast forward) the tape to the desired point. 3 Press m to begin playback.
Precautions • When the camcorder is not in use, remember to remove the cassette tape, turn off the power, and disconnect the camcorder from the power source. • Always respect prohibitions or restrictions on the use of electronic equipment on commercial flights or in other sensitive areas. • Do not aim the lens at the sun. Do not allow direct sunlight to strike the camcorder lens or LCD monitor screen, whether or not recording is in progress, as it may damage the CCD sensor or LCD screen surface.
Precautions Dew Formation • What is “dew formation”? When cold water is poured into a glass, dew drops form on the glass. This clinging of water drops is called dew formation. • When dew forms in your camcorder. Dew will gradually form on the head drum of your camcorder and make the video tape stick to the head. This causes damage both to the head and the tape. When dew forms, recording and playback may not function properly.
Dirty Video Heads When the video heads have become clogged with dirt (dust and tape coating particles), Striped noise Mosaic noise • mosaic-like noise appears on the playback picture. (see above illustration) • playback pictures do not move. • during playback, the whole screen becomes blue.
Supplied Accessories Battery pack BT-L225 AC adapter Power cord CR2025 type lithium battery Audio/video cable Lens cap Lens hood Wrist strap Tripod adapter vii VL-NZ50E-E-*i-x 7 02.4.
Optional Accessories Standard-life battery pack BT-L225 Extended-life battery pack BT-L445 Note: • Some of these accessories may not be available in selected areas. viii VL-NZ50E-E-*i-x 8 02.4.
Contents Operation References Part Names .................................................................... 1 On-screen Display Index ............................................... 4 Warning Indicators ......................................................... 6 Preparation Attaching and Removing the Battery Pack .................... 7 Charging the Battery Pack ............................................. 8 Powering the Camcorder from an AC Outlet .................
Camera Recording Manual Focus .............................................................. Manual Exposure ......................................................... White Balance Lock ..................................................... Setting the Camcorder to Full Auto Mode .................... Digital Picture Effects ................................................... Scene Menu (Program AE) .......................................... 37 38 39 39 40 41 Playback Using the Time Code ...................
Operation References Operation References Operation References Part Names For details on the use of each part, refer to the page number indicated in brackets. Front view Stereo microphone Zoom lens DC input jack [pp. 8, 9] Cassette holder [p. 10] Lithium battery compartment door [p. 11] Cassette compartment door [p. 10] Cassette compartment door release [p. 10] 1 VL-NZ50E-E-001-006 1 02.4.
Operation References Rear view Power Zoom Wide angle/ Telephoto control [p. 17]/ VOLume control [p. 19] DV terminal [p. 44] GUIDE ON/OFF switch [p. 23] AV jack [pp. 21, 43] Operation button Jack cover [pp. 21, 43, 44] LCD monitor 2 VL-NZ50E-E-001-006 2 02.4.
Operation References Operation References Rear view RECord START/STOP button [p. 16] STILL button [p. 29] GAMMA/ BRIGHTER button [pp. 25, 26, 35] FADE button [p. 27] Power switch (CAMERA/VCR select switch) [pp. 16, 19] SET button [p. 22] Speaker MENU button [pp. 5, 22] MANUAL button [p. 5] Bottom view Battery release [p. 7] Wrist strap loop [p. 13] Tripod adapter socket [p. 29] Battery mounting surface [p. 7] 3 VL-NZ50E-E-001-006 3 02.4.
Operation References On-screen Display Index For details on the use of each function, refer to the page number indicated. CAMERA mode p. 18 p. 30 S E T T I NG 1 P I C. E F F E C T S C E N E ME NU QK . R E T U RN R E T U RN p. 40 p. 41 p. 28 LCD SE T BA CK L I GHT L C D B R I GH T L C D C O L O UR R E T U RN p. 48 S E T T I NG 2 D G T L Z OOM T APE SPE ED DIS 16 : 9 A UD I O MOD E R E T U RN p. 24 p. 32 p. 30 p. 30 p. 33 CLOCK SE T D I SPLA Y S E T T I NG 12H / 24H R E T UR N p. 35 p. 12 p.
Operation References Operation References Manual screens Each time you press the MANUAL button, the screen changes as shown below. AUTO MAN . F O C U S AUTO E X POSURE Focus setting screen (p. 37) AUTO Exposure setting screen (p. 38) AUTO MANUAL button AUTO WH I T E B A L . White balance screen (p. 39) AUTO Normal screen AU T O 3 0 min On-screen indicators on/off Each time you press the MENU button, the screen changes as shown below. • The example screens shown are for CAMERA mode.
Operation References Warning Indicators If a warning indicator appears on the screen, follow the specified instructions. Displayed for the first 3 seconds Displayed after 3 seconds I NSER T A CASS E T TE. Description of warning There is no video cassette in the camcorder. Insert a cassette (see page 10). E J E C T T HE CAS SE T T E . E J E C T THE CAS SE T T E . The video cassette is defective and should be removed (see page 10). CASSE T T E NOT RE CORDA BL E. P RO T E C T .
Preparation Preparation Attaching and Removing the Battery Pack Attaching Preparation Power switch 1 Make sure that the Power switch is set to OFF. 2 Align the = mark on the side of the battery pack with the = mark on the camcorder (1), and slide the battery pack in the direction of the arrow completely until it locks into place (2). Removing 1 Make sure that the Power switch is set to OFF. 2 Rotate the monitor section of the camcorder (1), then press the battery release (2).
Charging the Battery Pack 1 Connect the supplied power cord to the AC power socket on the AC adapter, and insert the AC plug into a power outlet. AC power socket To power outlet 3 Insert the DC plug into the DC input jack. • The charge indicator lights up. DC input jack Battery pack Charging Max. continuous Max. continuous time recording time playback time BT-L225 approx. 2hr. approx. 1hr. 30min. approx. 1hr. 30min. BT-L445 approx. 3hr. 30min. approx. 3hr. approx. 3hr.
Preparation Powering the Camcorder from an AC Outlet You can also power the camcorder from a power outlet by using the supplied AC adapter. Preparation Caution: • The supplied AC adapter is specially designed for use with this camcorder, and should not be used as a power supply for other camcorders. 1 Make sure that the Power switch is set to OFF. 2 Connect the supplied power cord to the AC power socket on the AC adapter, and insert the AC plug into a power outlet.
Inserting and Removing a Cassette Inserting 1 4 Wait for the cassette holder to fully retract. Close the compartment door by pressing the centre until it clicks into place. Preparation Attach the power source to the camcorder, then slide the cassette compartment door release and open the cassette compartment door. • After confirmation sound, the cassette holder extends and opens automatically. Cassette compartment door release Removing Perform step 1 above, then take out the cassette.
Preparation Installing the Lithium Battery Installing Removing Perform steps 1 and 2 above, then lift out the battery from the battery holder. Preparation The supplied lithium battery is used to store the memory of the date and time settings. 1 Slide the cassette compartment door release and open the cassette compartment door. Note: • The cassette holder will extend and open when the camcorder is connected to a power source.
Setting the Date and Time 4 Press l or m to select “2” (day), then press the SET button. SE T T I NG Example: Setting the date to 2 June 2003 (2. 6. 2003) and the time to 10:30 am (10:30). Power switch 5 Press l or m to select “6” (month), then press the SET button. 6 Press l or m to select “2003” (year), then press the SET button. SE T T I NG MENU button Operation button Note: • Before performing the steps below, make sure that the lithium battery has been installed (see page 11).
Preparation Changing to the 12-hour Time Mode 1 After performing step 8 above, press l or m to select “12H/24H”, then press the SET button. Preparation CLOCK SE T D I SPLAY S E T T I NG 12H / 24H R E T URN 2 3 Turn the lens hood in the direction of the arrow to attach it. 2 4H 1 2H Press l or m to select “12H”, then press the SET button. 1 2 H 2 4H Attaching the Lens Hood 1 2H Press the MENU button to turn off the menu screen.
Using the Lens Cap Attach the strap to the lens cap as shown below. Always attach the lens cap when not using the camcorder. Preparation Lens hood Attach the strap of the lens cap to the wrist strap as shown below. Note: • Be sure the lens hood is attached to the comcorder before attaching the lens cap. When recording, hang the lens cap on the wrist strap to keep the cap out of the way. 14 VL-NZ50E-E-007-015 14 02.4.
Preparation Tips on Recording Positions To create images that are easy to watch during playback, try to record with an upright posture and steady hand to prevent a shaky image. Preparation Holding the camcorder Place your right thumb close to the REC START/STOP button and Power Zoom control. Place your left thumb on the thumb rest on the left side of the screen. Basic posture Shooting from a high angle Turn the LCD monitor so that the screen faces downward.
Basic Operations Camera Recording Easy Camera Recording in Full Auto Mode • Before you start recording, perform the operations described on pages 7 through 15 to prepare your camcorder for recording. To pause recording Press the REC START/STOP button again. Recording pauses, and the camcorder enters Recording Standby mode. PAUSE REC START/STOP button Power switch To turn the power off 1 2 Remove the lens cap. Hold down the Lock button and set the Power switch to CAMERA.
Basic Operations Camera Recording Zooming Auto Focus Zooming allows you to move visually closer to or farther from a subject without physically changing your position. When using the optical zoom, you can enlarge the subject up to 10K. Zooming in (when you want to centre attention on the subject) Wide angle Basic Operations Zooming out (when you want to includes the surroundings) The camcorder is preset to Auto Focus mode, which is designed to focus on most types of subjects.
Remaining Recording Time Display When the camcorder is recording, an onscreen indicator displays the approximate remaining tape time in minutes. When using the camcorder with the battery pack as the power source, the remaining battery power indicator is displayed. If the battery power becomes very low, a warning indicator appears. Replace the battery pack.
Basic Operations Basic Operations Camera Recording Playback Playback To stop playback The LCD monitor screen functions as a handy playback monitor. Nothing needs to be connected, allowing instant on-screen playback with the sound through the built-in speaker. Press l. Power switch To turn the power off Set the Power switch to OFF without pressing the Lock button. Basic Operations Note: • The tape is automatically rewound when playback reaches the end of the tape.
Still Video Search The video search function makes it easy to search for a desired scene on the tape. Searching for a Scene Near the Current Tape Position 1 During playback, press m on the Operation button. During playback, press k (or j) on the Operation button. • The playback picture fast forwards (or reverses). When you find the scene, press m to return to normal playback. To return to normal playback, press m again. Notes: • The sound is off in Still mode.
Basic Operations Playback Watching Playback on a TV Caution: • Check that the camcorder, TV, VCR and other equipment to be used are turned off before making any connections. Picture noise or malfunction may occur if any of the above is left on while making a connection. You can connect the camcorder to a TV to allow a larger audience to enjoy playback. 1 Open the jack cover on the camcorder (see page 2). 3 Turn on the TV and set it to the “AV” or “VIDEO” channel. (See the operation manual of your TV.
Useful Features 3 Using the Menu Screens Press l or m on the Operation button to select the desired menu screen (Y), then press the SET button. Example Use the menu screens to adjust the various camcorder settings. S E T T I NG 2 D G T L Z OOM O F F T APE SPE ED DIS 16 : 9 A UD I O MOD E R E T U RN Power switch SET button • You can press k, instead of the SET button. MENU button Operation button 1 4 Example Set to the desired camcorder mode (CAMERA or VCR).
Useful Features Useful features Camera Recording Camera Recording Displaying the Recording Guide This function helps you decide on the size of the subject occupying the screen. Select one of five recording guides. Types Turning on the recording guide Set the GUIDE ON/OFF switch to ON in Recording Standby mode. Selecting the recording guide Press l or m on the Operation button. Cross: A cross mark at the centre of the screen for placing the subject at the centre.
Setting the Digital Zoom The “D” digital zoom indicator is displayed during digital zooming. You can select three different zoom ranges: 1– 10K (optical zoom), 10–40K (digital zoom) or 10–300K (digital zoom). The digital zoom allows you to record powerful close-up pictures with the same operation as normal zooming. Notes: • The digital zoom is in addition to the optical zoom giving a combined maximum zoom range of 1–300K.
Useful features Camera Recording Gamma Brightness Compensation To obtain a brighter picture Press the GAMMA/BRIGHTER button again. • The x indicator appears. When the subject is backlit, the image will appear dark if it is recorded normally. The gamma brightness compensation function improves the picture by increasing the brightness of the subject while leaving the brighter portion of the image unaffected.
Gain-up To obtain a brighter picture When you are recording in a dark or poorly illuminated location, “LIGHT” is displayed on the screen. Use the gain-up function to record a brighter picture. Press the GAMMA/BRIGHTER button again. • The e indicator appears. GAMMA Note: • At locations where lighting is adequate, “LIGHT” will not appear. The gain-up function cannot be used in this case. AU T O 3 0 min To cancel the gain-up function Press the GAMMA/BRIGHTER button until “GAMMA” disappears.
Useful Features Camera Recording 2 Fade In and Fade Out Press the REC START/STOP button to begin recording. • The picture turns white, and the image and sound fade in. The fade function allows you to gradually bring the image and sound in or out at the beginning or end of a scene for creating scene transitions. This is especially effective in creating a dramatic change in scenery.
Quick Return Edit Search If while playing back your tape you want to quickly return to the last recorded scene and start recording again, use the quick return function. 1 In Recording Standby mode, press the MENU button until the menu screen appears. 2 Press l or m on the operation button to select T, then press the SET button. 3 Press l or m to select “QK. RETURN”, then press the SET button.
Useful Features Camera Recording Still Recording You can record continuous still images of subjects. 1 In Recording Standby mode, press the STILL button fully. • A still image of the subject is displayed. 2 Attaching the Supplied Tripod Adapter Attach the supplied tripod adapter when using a tripod with the camcorder. 1 Align the tripod adapter with the tripod adapter socket on the bottom of the camcorder, then rotate as shown below. Tripod adapter socket Press the REC START/ STOP button.
Wide Screen (16:9) The wide screen function lets you record scenes with the wide-screen feel of a movie shown in a theatre. The top and bottom of the picture are masked with black bands to produce an effective screen aspect ratio of 16:9. Wide screen Normal screen 1 In CAMERA mode, press the MENU button until the menu screen appears. 2 Press l or m on the operation button to select Y, then press the SET button. 3 Press l or m to select “16:9”, then press the SET button.
Useful Features Camera Recording Self Recording Rotate the LCD monitor 180° vertically so that the screen faces the other way and the subject can monitor the shot while you are recording. If the camcorder is steadied, you can record yourself in the scene by watching yourself on the LCD monitor. Cautions: • Do not rotate the monitor section to the self recording position during recording or playback. • For recording in Self Recording mode, be sure to rotate the monitor section, NOT the lens section.
Recording in LP (Long Play Recording) Mode This camcorder allows you to record in LP (Long Play Recording) mode for approximately 50% more recording time with the same picture quality as that in SP (Standard Play Recording) mode. 1 In CAMERA mode, press the MENU button until the menu screen appears. 2 Press l or m on the operation button to select Y, then press the SET button. 3 Press l or m to select “TAPE SPEED”, then press the SET button.
Useful Features Camera Recording Selecting the 16-bit Audio Recording Mode The camcorder normally records audio in the 12-bit audio recording mode. For higher-quality audio recording, select the 16-bit audio recording mode. 1 In CAMERA mode, press the MENU button until the menu screen appears. 2 Press l or m on the operation button to select Y, then press the SET button. 3 Press l or m to select “AUDIO MODE”, then press the SET button.
Useful Features Playback Using the Remote Control (Not supplied) The remote control (RRMCG0084TASA) is not supplied with this camcorder. Contact the nearest SHARP service centre or your dealer for purchasing as a specified part. Installing the Batteries 1 2 Open the battery compartment cover. Insert the two commercially available AA (R6 or UM/SUM-3) batteries with the battery poles positioned as indicated. Press l or m to select “ON”, then press the SET button.
Useful Features Playback Displaying the Date and Time of Recording Follow the procedure below to display the date, or both the date and time, of recording on the screen. You can display the date and time during both recording and playback. Gamma Playback The gamma playback function improves the playback picture in VCR mode by increasing the brightness of the subject while leaving the brighter portions of the image unaffected. • The example screens shown are for CAMERA mode.
Picture Effect Playback 4 These picture effects let you play back images with a more dramatic effect. Types B/W: The picture is displayed in black-andwhite. SEPIA: The picture is displayed in sepia colour similar to that of an old photograph. SOLARI: The contrast of the subject is enhanced, creating a unique artistic image. NEGA: The blacks and whites of the image are reversed and colours of the image are inverted. BLUE: The picture is displayed with the effect of playback through a blue filter.
Advanced Advanced FeaturesFeatures Camera Recording Camera Recording 1 Manual Focus Auto Focus may not be able to focus on the subject in the situations shown below. In such situations, set the camcorder to Manual Focus mode and focus manually. Subject is too dark. Fast-moving subject. Lack of contrast, e.g. snow scene. AUTO MAN . F O C U S Adjust the Power Zoom control to frame the subject as you desire. 3 Press m or l to focus on the subject.
Manual Exposure The camcorder is preset to Auto Exposure mode, which automatically selects the optimal aperture. However, when there is too much contrast in brightness between the subject and background, you may not be able to record a clear image. In this case, use the manual exposure function to correct the exposure level. To return to Auto Exposure mode Press the SET button while the exposure setting screen is displayed. Note: • Manual Exposure mode will cancel if a scene setting is selected thereafter.
Advanced Features Camera Recording White Balance Lock The colour of the subject on the screen looks different depending on lighting conditions. Lock the White Balance if the Auto White Balance does not work properly. 1 In CAMERA mode, press the MANUAL button until the white balance setting screen appears. AUTO WH I T E B A L . 2 AUTO Aim the lens at a white object. • Adjust the distance of the object so that the entire screen is white.
Digital Picture Effects 4 These digital picture effects let you record the subject with a more dramatic effect. Press l or m to select the desired digital picture effect, then press the SET button. • The selected digital picture effect displays on the menu screen. Types P I C. E F F E C T B W B/W: To record in black-and-white. SEPIA: To record in sepia colour similar to that of an old photograph. SOLARI: To record with enhanced contrast, creating a unique artistic image.
Advanced Features Camera Recording 4 Scene Menu (Program AE) You can set the camcorder to the shooting mode that will create the best results for a specific situation. Just select one of four scene settings shown below. The camcorder will automatically set the exposure, white balance, and shutter speed to produce the optimum picture quality for the selected situation. Types SPORT: When you want to record a fastmoving subject. SUNLIGHT: When the background is very bright.
Advanced Features Playback Using the Time Code 5 Press the MENU button to turn off the menu screen. • The time code appears when the onscreen indicators are turned on. The time code shows the hour, minute and second of recording, and the frame number (1 frame = approx. 1/25 sec.). This is automatically recorded along with the subject when you are recording on the tape. You can display the time code on the screen as an accurate counter in both VCR and CAMERA modes.
Advanced Features Playback Editing Cutting Unwanted Sequences Video editing lets you refine your videos by removing unwanted sequences from your tape, or transposing one sequence with another. This camcorder lets you monitor the source program on the built-in LCD monitor without having to connect it to an external TV or video monitor. Connect the camcorder to a VCR with the supplied audio/video cable, as shown.
Editing with the DV Terminal (IEEE1394) This camcorder enables you to perform digital video editing. Connect the camcorder to video equipment with a DV terminal using a commercially available DV cable. A DV cable is able to transfer all dubbing signals including video and audio. To Record to Video Equipment To Record from Video Equipment 1 Set the camcorder to VCR mode, and insert a Mini DV cassette. 2 Begin playback on the video equipment connected to the camcorder.
Advanced Features Playback Audio Dubbing Feature You can add narration to recordings made with this camcorder, while preserving the original audio and video recordings. Microphone for Audio Dubbing You can use the built-in stereo microphone to record narration. Built-in stereo microphone Audio Recording In normal recording mode 12-bit audio recording The audio is recorded in stereo on Audio 1.
Audio Dubbing To pause audio dubbing 1 Play back the recorded Mini DV cassette and locate the tape position where you wish to start audio dubbing. Press the SET button. To resume audio dubbing, press the SET button again. 2 3 Press m to pause playback. Press the MENU button until the menu screen appears. 4 Press l or m on the operation button to select V, then press the SET button. 5 Press l or m to select “AUDIO DUB”, then press the SET button. • The audio dubbing screen appears.
Advanced Features Playback Selecting the Audio Playback Mode You can select any of the following audio playback modes.
Appendix Picture/Backlight Adjustments Adjusting the Backlight 1 Press the MENU button until the menu screen appears. If the picture is difficult to see due to ambient light or other factors, adjust the monitor picture settings. 2 Press l or m on the operation button to select O, then press the SET button. • The example screens shown are for CAMERA mode. 3 Press l or m to select “BACKLIGHT”, then press the SET button. Adjusting the Picture 1 Press the MENU button until the menu screen appears.
Appendix Turning off the Confirmation Sound A confirmation sound is made when you turn on or off the Power switch, press the REC START/STOP button, or perform other designated operations. Use the procedure below to turn off the confirmation sounds. 1 Press the MENU button until the menu screen appears. 2 Press l or m on the operation button to select I, then press the SET button. 3 Press l or m to select “BEEP”, then press the SET button.
Useful Information Hints for Better Shooting • Position the subject in the centre of the scene. When using auto focus, whatever is in the centre of the scene is kept in focus. Lighting For clear, good-quality recording, 500 to 100,000 lux is needed. Recording is possible with less light, but the picture quality may suffer. Adequate lighting is also essential for correct white balance. Brightness (Lux) Situation (Lux) Blue sky • Avoid backlit subjects.
Appendix DV Technology Copyright Protection Digital video (DV) is a revolutionary technology that enables recording and playback of high quality images with the use of special digital features previously unavailable with conventional analog formats. DV and conventional video cassette tapes There are two kinds of DV-format video cassette tapes: the Mini DV cassette and the larger DV cassette used for extended playback and recording. This camcorder only operates with Mini DV cassettes.
Mini DV Cassette To protect recordings against accidental erasure Slide the protect tab on the rear of the Mini DV cassette to the “SAVE” position. Erasure protect tab Precautions when using a Mini DV cassette To record over a previously recorded tape, slide the protect tab to the “REC” position. AC Adapter • The AC adapter may interfere with reception if used near a radio. • Prevent flammables, liquids, and metal objects from entering the adapter. • The adapter is a sealed unit.
Appendix Battery Pack Storage This camcorder uses a lithium-ion type battery pack. Charging • Charge the battery pack immediately (or a day) before use. The battery pack gradually self-discharges even if stored in a fully charged state. • Charge the battery pack between 10°C and 30°C. • Fully charge the battery pack. Use of an insufficiently charged battery pack will shorten actual time of use. • Refresh (discharging before charging) is unnecessary.
Cleaning Using Your Camcorder Abroad • Many plastic parts are used in the camcorder casing. Do not use thinner, benzene or other strong chemical cleaners. These may cause discolouration and damage to the casing. • Clean the casing with a soft, dry cloth. If the casing is particularly dirty, wipe the casing with a tightly wrung cloth dampened with a diluted, neutral detergent. Then wipe it again with a soft, dry cloth. • Use a soft cloth to wipe finger marks and other smudges off the LCD screen.
Appendix Demonstration Mode You can watch a brief demonstration of the special camcorder features in Demo mode. If the demonstration appears on the screen when you turn on the camcorder for the first time, cancel the Demo mode to use your camcorder. Watching the Demonstration 1 2 During the demonstration, press the MENU button to pause the demonstration. 2 Press l or m on the operation button to select I, then press the SET button. 3 Press l or m to select “DEMO MODE”, then press the SET button.
Before Requesting Service Before calling for service, please check the following troubleshooting table. Symptom Power No power. Suggested solution Power source is not properly connected. Connect power source properly (pp. 7, 9). Battery pack is not charged. Charge battery pack sufficiently (p. 8). Dew in camcorder. Wait until dew dries (p. v). Safety function is in effect. Set Power switch to OFF and remove battery pack. Wait for 2 seconds, then reinstall battery pack and turn on power (p. 7).
Appendix VCR mode Symptom Suggested solution Rewind or fast forward tape to desired point (p. 19). Video noise in image. Dirty video heads. Call for service or use a commercially available cleaning tape (p. vi). Old or worn tape. Use a new cassette. Power source is not properly connected. Connect power source properly (pp. 7, 9). Battery pack is not charged. Charge battery pack sufficiently (p. 8). Camcorder is recording. Stop tape and try again (p. 16). Backlight has been turned off.
Specifications Camcorder Signal System: Recording System: Cassette: Recording/Playback Time: Tape Speed: Pickup Device: Lens: Lens Filter Diameter: Monitor: Microphone: Colour Temperature Compensation: Minimum Illumination: Power Requirement: Power Consumption: Operating Temperature: Operating Humidity: Storage Temperature: Dimensions (approx.): Weight (approx.): AC Adapter (UADP-0342TAZZ) Power Requirement: DC Output: Dimensions (approx.): Weight (approx.
Note VL-NZ50E-E-59(Note) 59 02.4.
SHARP CORPORATION Printed in Japan TINSLA004WJZZ 02P04-JKG VL-NZ50E-E-hyou4 1 02.5.
