VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E SERVICE MANUAL S42H9VL-NZ50S SERVICE MANUAL LIQUID CRYSTAL DIGITAL CAMCORDER MODELS PAL VL-NZ50S/H/E/W VL-NZ80H VL-NZ100S/H/E LIQUID CRYSTAL DIGITAL CAMCORDER In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified be used. CONTENTS PAL MODELS VL-NZ50S/H/E/W/NZ80H/NZ100S/H/E Page 1. SPECIFICATIONS ..........................................
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 1.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 2. PART NAMES For details on the use of each control.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 3. DISASSEMBLY OF THE SET Note: Before removing the cabinet, turn off the power supply, and ascertain that the battery have been removed. 1. 3. (c) (c) (c) (c) LCD Panel (c) FPC (h) (h) (c) (i) (c) Battery Unit Radiation Angle 1) Remove the 1 screw ((i)XiPSF17P03000) and 2 screws ((h)XiPSF17P02000). 2) Remove the 2 screws ((c)XiPSN17P03000) to detach the VCR operation PWB. Then remove the FPC of the LCD panel and FPC of the reflector to detach the LCD panel.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 5. 7. (i) (c) Microphone Cover Camera Front Cabinet (c) (o) (i) (i) Mechanism (i) NZ50S/H/E/W NZ80H/NZ100S/H/E (i) (i) (i) (k) (c) (k) (h) Camera Rear Cabinet (c) (k) Camera Rear Cabinet (c) 1) Remove the 3 screws ((c)XiPSN17P03000), 4 screws ((i)XiPSF17P03000) and 1 screw ((h)XiPSF17P02000) (NZ50S/H/E/W only) fixing the camera rear cabinet to detach it. (Note: When detaching the camera rear cabinet, pay attention to the FPC of the camera operation unit.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 4. MECHANISM ADJUSTMENT JIGS AND PARTS 4-1. Mechanism check adjustment jigs 1. PB-use cassette Torque meter 2. 9DASD-1015 3. DB * 1mN·m/1.5mN·m 1. Torque gauge 2. JiGTG0045 3. CN * For use in VS-REW winding torque measurement. 1. Torque gauge head 2. 9EQTGH-DH5000 3. BW * For use with the torque gauge listed left. 1. Tension gauge 4N 2. JiGSG0400 3. BK * For measurement of pinch roller pressure. Configuration 1. Name 2. Part No. 3.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 5. INSPECTION AND MAINTENANCE ITEMS AND INTERVALS In order to keep the mechanical section always in good condition, perform the following inspection and maintenance at regular intervals. In addition, after repair, perform the following maintenance items regardless of how long the user has been using the unit. 5-1.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 6. MECHANICAL ADJUSTMENTS AND CHECKS The items discussed here relate to general on-site servicing (field servicing). Adjustments and replacements that require sophisticated facilities, jigs and technology are omitted.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 6-4. Back tension torque check and adjustment in record (playback) mode AC adapter used, with cassette controller assembly (1) Checking Set the torque cassette (SD-1015), and make sure in the SP record mode that the supply side torque is within the standard shown below (or in the playback mode for the tape on which the signal has been SP-recorded). (If torque ripple exists, read its center value.) 0.7 ± 0.1mN·m (2) Adjustment (Fig.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E (If the tension fluctuates, read its center value.) 15 ± 12mN 6-8. Checking of winding Tu reel base ratchet torque DC3V, without cassette controller assembly (Independent Mechanism) (1) Remove the cassette controller assembly, then apply DC3V to the loading motor and put the system into standby mode. (refer to 8-1) (2) Move the swing arm toward the S reel base side. Be careful not to cause damage to the gears and other parts in the process.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 7. TAPE RUNNING ADJUSTMENT 7-1. Adjustment locations · T roller, arm · Tu guide, arm · Slide chassis Adjust the height of only replaced parts with the adjusting jig. Adjustment procedure 7-2 · S guide · Pole base · Guide roller · Drum assembly · Capstan motor, etc.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 7-4. Running rough adjustment (With cassette controller) 1) Su, Tu guide roller height adjustment Entrance side NG (1) Loosen the guide roller lock screw, then tighten loosely so that the roller turns easily. (2) Replay an alignment tape, and adjust the Sup, Tu guide roller so that the envelope sides of entrance and exit are flat. (3) Perform ± 1/4 shift, then, as in the above case, adjust until the envelope becomes flat.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 8. MECHANICAL SECTION ASSEMBLY AND PARTS REPLACEMENT (DISASSEMBLY AND REASSEMBLY) Mechanical section disassembly and reassembly are explained in this section. For removal of the cabinet, etc., refer to 3. DISASSEMBLY OF THE SET. 1. Always replace cut washers that have been removed, for example in parts replacement, with new ones. 2. When reassembling, be careful not to allow screws, washers or foreign matter to enter. They can cause mechanical misoperation.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E (6) STOP mode (5) PLAYBACK (RECORD, FF, VSF) mode The system is in the STOP (Rec Lock in CAMERA mode) The mechanism position for playback, record, FF and fast position; the S and the T pole bases are snap-fitted to the drum feed playback. base, the S brake is in contact with the S reel base, and the Tu The pinch roller is pressed to the capstan shaft, and the S/Tu brake is in contact with the Tu reel base. main brake is separated from the S/Tu reel base.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 8-3. How to operate with the circuit board without the cassette controller assembly. In this method, if the procedure is followed incorrectly there is danger of damaging the mechanism and the tape, so except in special cases, such as when measuring the VSR torque, do not perform this procedure. Normally operate this unit with the cassette controller assembly attached. Be sure to follow each caution mentioned.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 8-5. Reassembly 8-5-1. Reassembly in side of the main chassis. Note) Numbers before part names are given as a guide to the order of assembly. As for greasing/oiling/cleaning places refer to the attached drawings (Grease/Oil application side of the main chassis). 1. Groove grease 4.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 8-5-2. Reassembly in side of the Slide chassis. Note) Numbers before part names are given as a guide to the order of assembly. As for greasing/oiling/cleaning places refer to the attached drawings (Grease/Oil application side of the slide chassis) 2. 1. Sensor FPC cover Grease F K Main brake SPR.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 8-5-3. Main chassis assembly and slide chassis assembly assembling method (1) Enter the coupling mode. (In this position, the cam groove of the T arm operation lever in the figure is parallel to the side of the main chassis, and the poll base is slightly moved.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E GREASE/OIL APPLICATION From rear surface side Rear surface · groove side surface Front surface · rear surface · groove side surface Drum base assembly From rear surface side Main cam Loading lever Tu loading arm S loading arm Intermediate gear angle Enabled after assembling Including groove side surface Enabled after assembling O : Oiling(Cosmo Hydro HV22) G : Greasing(Moly Coat YM-103) : Greasing(Moly Coat YM-103) Pinch control lever Capstan FPC stopper T a
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 9. ADJUSTING THE ELECTRICAL CIRCUITS Before starting the electric circuit adjustment • The adjustment methods described herein are used, in most cases, when the expendable mechanical parts, including the video head, have been replaced, at which time the electrical circuits need to be readjusted. Before adjusting the electrical circuits, make sure that the mechanism works properly (i.e., the mechanism is properly adjusted).
SPEAKER VSP0020P-918N QSW-ZA003WJZZ ZOOM OPERATION SW UNIT QSW-ZA004WJZZ POWER/SNAP SW UNIT SC2701 12 16 LENS UNIT LENS FPC Direct connection 15 14 13 CCD PWB TURN SW UNIT QSW-Z0376TAZZ 17 QPWBHB194WJZZ SC21 SC551 18 QCNW-2060TAZZ 19 CAM HEAD PWB SC101 10 SC1502 AUDIO I/O PWB SC2601 9 SC1202 8 MAIN PWB SC3301 P306 SC900 SC701 2 1 QCNW-1832TAZZ HEAD AMP UNIT HEAD AMP FPC CPWBH2876TA01 SC1204 SC2801 21 QCNW-A392WJZZ P2900 DC Jack PWB CPWBHB195WJ01(NZ80/NZ100) CPWBHB
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E [TEST POINT] (Wiring board diagram: Main Side A) TL2801(C OUT) COMMON PULSE C2800 R2811 Q2806 Q2907 R3495 R443 R2807 IC2803 R3492 R3493 Q2805 R2912 C3462 TL919 R2915 TL2905 TL2907 TL3319 TL3318 TL3317 TL3333 TL3316 TL3315 TL3314 TL3313 C901 TL903 TL900 TL902 TL901 D2908 TL3337 TL2906 TL997 TL906 TL905 TL904 Q2902 R418 TL418 D2904 Q911 TL1472 C992 R951 R950 R7415 TL1478 R2911 R7413 R7419 R414 C974 L917 R2919 L915 D7401
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E (Wiring board diagram: AIO Side B) TL608 EE level check TL609 Frequency character check EE level check Frequency character check TL609 TL608 TL2687 0 C637 R631 TL2689 TL2645 R632 C631 TL2653 TL2663 C636 C633 C629 R627 C624 R623 C628 TL2683 TL2688 R628 R619 C617 R641 TL2680 C613 TL2644 C609 R613 TL2691 R642 C612 TL2692 TL2667 R643 TL2673 IC601 C642 R612 C2610 TL2675 C615 C616 TL605 TL2686 R638 TL2690 R622 C626 C621 R626 C623 R621
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E [Making adjustments] Adjusting the servo system controller and related parts 1. Setting the system codes Replacement of IC705 E2PROM requires the following data to be set in this order. [Procedure] Set the unit to the VCR mode and set the data for each address. Code 1. Model code Address 01 09 Data NZ50S 00 FF NZ50H 00 FF NZ50E/W 00 FF NZ80H 03 FC NZ100S 04 FB NZ100H 04 FB NZ100E 04 FB 2.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 3. SHUT OFF adjustment Mode Procedure Examples VCR ADJ mode 1) Load a recordable tape, and set the camera mode. (Set TL911 to GND or SW901 to ON.) 2) Press the "CONTINUE" and then the "TEST SEL" on the remote control for adjustment to enter the TEST mode (T-01 blinks). 3) Select T-03 with the FF or REW key and then press the PB key. 4) Observing the power voltage from TL2905(-), set it so that TL904(+) obtains 5.95V ± 50mV. 5) Press the MENU button on the main unit.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E ADJUSTING THE VIDEO I/O CIRCUIT SYSTEM (Wiring board diagram: Main Side A) R2915 C2901 R1480 TL2905 R2910 R2860 R2857 R2858 R913 R2914 FB2801 C2903 TL901 TL2907 TL902 TL900 TL903 C901 D2908 TL2906 R2908 R2909 TL997 P901 D2902 R2918 CP2 R2902 TL906 R2904 R2901 D2901 R2903 R1483 C2902 VA1402 TL1479 C990 TL1470 TL1471 TL2903 TL2901 R2917 D2903 Q2904 TL2902 Q2901 C930 R2905 R2907 D2905 TL905 TL904 Q2902 CP1 TL2904 R2906
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E ADJUSTING THE LCD CIRCUIT * To make this adjustment, set the backlight switch to the "NORMAL" position.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 4. COM-BIAS adjustment Test point Mode Procedure Adjustment rating Remark Examples LCD panel display surface Address VCR ADJ 33 VCR AV input 1) Set the data of the address 582 to AF. 2) Set up the illuminance meter (TOPCON IM-3) on the LCD panel surface. (The outside light must not enter.) 3) Minimize the ripple of the output waveform of the illuminance meter. 4) Return the data of the address 582 to the initial value. (Initial value: 40) Minimum Response time : 0.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E ADJUSTING THE MIC AMP CIRCUIT (Wiring board diagram: AIO Side B) TL608 EE level check TL609 Frequency character check EE level check Frequency character check TL609 TL608 C637 R631 R632 C631 C636 C633 C628 C629 R627 R623 C624 R628 R619 C617 R641 TL2680 C634 C627 R625 R630 R620 C619 TL26 R624 C620 TL607 C613 TL2644 R613 TL2691 R642 C612 TL2692 C610 SC2601 C614 R643 TL2673 IC601 C642 TL2675 R612 C2610 TL2691(INT MIC R) EE level check F
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E DV INTERFACE (IEEE1394) ID SETTING This unit has a DV interface function conforming to IEEE1394. Therefore, each individual ID number must be used for each unit. Since this ID is written on the E2PROM (IC302) on the head amp PWB, the ID must be newly written when replacing this IC or the head amp PWB. Address 180, 17F, 17E Mode VCR Adjustment rating ID number obtained from the URL below Procedure 1) Refer to the ID code application below.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E (5) Click on [Repair use]. Click (6) Input the necessary information for the application. For the indispensable input items, be sure to input them. Select the [Group/company] and [Kind name] from the list. Input the [Model name]. Input the [Serial number]. Input the [Site/department of repair]. (7) Click on [motion]. The confirmation screen will appear. (8) Click on [Yes]. 2. Print the application result. (1) Print out the application result screen.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 9-2. Camera Section Adjustments 9-2-1. Camera section service (1) Camera adjustment is performed after the set has been completed. (2) Subjects, measuring instruments and jigs needed for camera section service and adjustments • • • • • • Gray scale chart Color bar chart Oscilloscope Digital voltmeter Halogen lamp: 2 pcs.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 4) Operation flow FF or REW PLAY FF or REW PLAY STOP Address is selected and specified, with the data called. Then the called data are selected and fixed. The operation flows in this sequence. 5) When the adjustment is complete: Press the "CONTINUE" key to let the "CAM ADJ" display disappear from the screen.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E (4) Camera signal system adjustment mode In the camera signal system adjustment mode, the automatic white balance is disabled to allow for the adjustment of the camera unit. At this time, the white balance mode is fixed at the INDOORS mode and the focus mode is switched to the manual focus mode. 1) Shifting to the camera signal system adjustment mode Set the data for the address "0000" to " 00". ] This shifts the camera signal system adjustment mode.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 9-2-4. Adjustment procedures Adjustment method Item (1) Auto-focus adjustment Set the unit to the auto-focus function adjustment mode and write data to the address "0000" one after another. This executed the adjustments automatically. The items to be adjusted are as listed below. Every time an adjustment is made properly, the data "FF" is written to the address.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E Adjustment method Item (4) Iris AE coarse adjustment (1) Video output is observed with the oscilloscope in the grey scale standard record state, • Measurement terminal: the data of address "0002" is rewritten, and the luminance signal level is adjusted white S terminal luminance signal output to 760 ± 10mVp-p.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E Adjustment method Item (7) White balance adjustment(3200K) • Measurement terminal: EE output • Address: "0090" INDOOR_W/B R "0092" INDOOR_W/B R • Measuring instrument: Vector scope • Object: Grey scale • Data variation width: "0000" to "03FF" (1) White balance adjustment is performed repeatedly.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 10. USEFUL TIPS (PROBLEMS DIFFER FROM THOSE FOUND ON VHS OR 8MM DECKS BECAUSE THE SIGNALS ARE DIGITALLY PROCESSED.) Camera (EE mode) Picture fails to appear Camera (REC mode) VCR (PB mode) VCR (EE mode) Picture fails to appear when tape recorded on this unit or another unit is played back. (EE OK) Blueback fails to appear.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 11. SIGNAL FLOW DIAGRAMS 11-1.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E WAVEFORM DIAGRAM (DURING COLOR BAR PLAYBACK) 11-3.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 11-5. FLOW IN PB MODE (AUDIO) WAVEFORM DIAGRAM (1.
USB IC51 D/A-CON IC101 CDS/AGC REC (EE) PB IC552 IRIS DRIVE 36.000MHz IC22 TG IC21 V-Driver IC1 800K CCD-Sensor SD/MMC CARD IC5701 USB/CARD_CTL IC151 10bit A/D Video out IC1401 ANALOG VIDEO I/O IC201 16Mbit SDRAM CameraZoom IC202 CAMERA ENGINE (Total ASIC) CAM DSP IC701 MECHA/SYSTEM MiCON IC703 CHARACTER GENERATOR IC3702 16Mbit SDRAM PPW v1 OSD Synthesis IC3701 CAMERA/CARD MiCON M-CTL ZOOM LCD CTL PPW LCD IC4401 VIO ENGINE (Total ASIC) CODEC CLK. Gen CT INT.
IC21 V-Driver VHiUPD16510-1 20P OFD V1, V2, V3, V4 H1-CLK, H2-CLK, RS-CLK IC1 CCD-Sensor VHiMN39260F-1 V1, V2, V3, V4, VH1, VH2, SUB IC22 TG VHiMN52A7++1Q 48P FSX, FCDX, BCPX, PBLK, XRS 43 CAM-HEAD X21 36.
J1401 CAMERA SECTION BLOCK DIAGRAM CAM ENGINE 44 VIDEO IN/OUT VIDEO-IN IC1431 INPUT SW VHiMM1503XN-1 6P ZYP0 7 ZCP0 7 ZUVSELP ZCLKP ZHDP ZVDP IC1401 VIDEO I/O VHiMM1510XN-1 6P A-YC-OUT A-Y/COMP-V-IN IC4401 VIO ENGINE RH-iXA149WJZZ 303P CDY0 7, CDC0 7 REC (EE), PB PB REC (EE) R OUT G OUT B OUT CLD, SPD, CTR EX1, EX2,SPS, RES, CLS, LOW PSS1 CVDR, CHDR I/O SEL SC2801 VR, VG, VB IC2800 LCD INTERFACE VHiMM1323XV-1 24P IC452 REC/PB ENGINE RH-iX0809TAZZ 368P CDVDP CDHDP CDUVSELP VL-NZ50S/H
DI00 45 REC (EE), PB PB REC (EE) 15 11 7 7 XCS, XWE, XRAS, XCAS, XUDQM, XLDQM, XCKE, CLK18M1IV SM-ADR0 CVDR CHDR I/OSEL CDUVSELP CDHDP, CDVDP IC407 Codec External Memory 16M SDRAM RH-iXA193WJZZ 60P IC4401 VIO ENGINE RH-iXA149WJZZ 303P CDY0 CDC0 IC452 REC/PB ENGINE RH-iX0809TAZZ 368P X401 24.
REC (EE), PB PB REC (EE) REC/PB ENGINE BLOCK DODAT PDAD PDDA ADMCLK ADBCK ADLRCK DFSO DFSI AIDAT CS-1394, RD-1394, WR-1394 TPA-, TPA , TPB-, TPB AUD R AD IN AUD L AD IN AUD R DA OUT AUD L DA OUT IC1602 16Bit ADC/DAC VHiPCM3008+-1 16P MECHA/SYSTEM MICON DV CONNECT IC601 AIO VHiBH7761KV-1 48P INT MIC SP OUT AUDIO R I/O AUDIO L I/O SPEAKER AV JACK VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 12-5.
IC1 CCD Sensor 47 Focus-Motor Driver Zoom-Motor Driver IC551 Iris Drive IC552 Iris Amp IC21 V-Driver IC101 CDS AGC IC22 Timing Generator CCD IC51 D/A Converter X21 36MHz CAMERA HEAD IC3701 CAM/CARD µ-com IC151 10bit A/D-COnverter SSG Digital Auto C-Process Y-Process CAM ENG IC3702 16M SDRAM Electric Zoom Image Stabilizer Digital Noise Reduction IC202 Sirial Data PB Y/C Data 16M SDRAM IC201 REC /PB Y/C Data MAIN VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 12-6.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13. SCHEMATIC DIAGRAMS 13-1.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-2.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-3.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-4.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-5.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-6.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-7.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-8.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-9.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-10.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-11.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-12.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-13.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-14.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-15.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-16.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-17.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-18.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-19.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-20.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-21.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-22.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-23.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-24.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-25.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-26.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-27.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-28.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-29.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-30.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-31.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-32.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-33.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-34.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-35.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-36.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E -MEMO- 10 11 12 13 14 15 117 16 17 18 19
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-37.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 13-38.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 14.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 138 120 108 90 75 60 54 48 42 36 27 A C KV1812K EX1394CE HVC359TR HVU359TR HVU362 64 50 44 38 30 28 24 20 16 14 10 28 37 43 49 55 61 76 91 109 121 139 32 25 22 19 15 14 12 10 8 7 5 36 48 56 64 72 80 100 120 144 160 184 ADC08351 CXA2096N PCM3008 IX0940TA 92 80 72 60 50 40 36 32 28 24 18 47 41 37 31 26 21 19 17 15 13 10 9 12 14 16 18 20 25 30 36 40 46 1 BH7277KV MB3881++ PT8214 IX0947TA 1 UPD16835 NJM2902V LV4051AT MB88146A MM1323XV 93 81 73 61 51 41 37 33
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E 15.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E SIDE B J L911 C722 R739 C709 C716 C711 C713 TL1248 TL1247 TL412 Q705 Q704 C204 C212 TL204 C214 Q703 R722 R728 R709 R714 R797 R747 R729 R737 R720 R735 R733 R754 FB201 TL914 R745 R717 R742 R743 C731 R796 R723 R772 R712 C735 R724 R736 R738 R725 R741 R731 Q910 Q904 C728 C202 IC706 TL213 L912 TL918 TL1481 TL908 C705 C208 C738 C714 R727 R726 C715 TL5702 Q1201 R1998 R1995 R1927 R911 R1929 Q1911 R1930 C905 R926 C928 R927 R920 R914 R
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E CAMERA HEAD PWB SIDE A J IC21 C22 R21 C25 C24 C21 C23 I R22 C30 H C31 C26 R27 R23 R32 G X21 R24 IC22 R25 R31 P52 R30 R26 R29 F R28 P51 R34 R35 C27 L21 FB21 C33 R33 C32 R556 R558 Q21 R560 E R53 C34 C566 R561 D551 R576 R564 R563 R562 R566 C52 R583 IC51 R570 C53 R577 R574 C567 R568 R565 C565 D C C51 C563 Q551 R572 R573 R582 IC552 C564 C54 R581 R569 C568 C569 R580 R575 C570 R567 R571 R54 C571 1 B A
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E SIDE B J TL27 TL46 TL22 I TL25 TL52 TL45 TL29 SC21 TL35 TL574 TL575 H TL21 TL54 TL32 TL47 TL37 TL24 TL34 0 TL28 TL41 TL42 TL40 TL36 TL33 TL43 TL26 TL23 TL59 TL39 R51 R52 TL58 TL31 TL30 G TL57 TL69 TL44 TL71 R579 F SC551 R578 TL63 TL55 TL56 TL570 TL567 TL568 TL565 TL566 TL563 TL564 TL557 TL558 TL72 TL555 TL551 TL553 TL552 TL554 TL556 L551 C559 R552 R553 TL562 TL559 TL560 C561 R555 C552 R559 SC53 TL64 TL561
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E AUDIO I/O PWB J SIDE A I Q601 C607 H R639 R606 R2601 C611 R2630 R605 R2618 IC2601 C2605 R637 C2606 C643 C645 C644 C640 C618 L601 Q603 R2617 C2607 C2602 R2616 R2631 R636 G R2628 1 R2629 R604 R634 R635 R2606 C2608 R645 R2619 C641 R633 C2609 R603 Q604 C608 R607 SC2604 F Q605 C638 L602 C630 R2615 R2609 R2613 R2625 R2620 R2622 R2627 R2608 C632 C635 R2621 C604 D601 R2610 E P601 J601 D C B A 1 2 3 4 5 6 130
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E J SIDE B I TL609 TL608 TL2687 C639 TL2669 TL2655 TL2662 R624 0 C637 TL2689 TL2645 R632 TL2653 TL2663 C636 C633 C629 R627 C624 R623 R619 C628 TL2647 TL2683 TL2688 R628 C617 R641 TL2680 R631 C631 C620 C613 TL2644 C609 TL607 C634 C627 R630 C622 R625 R629 R620 R614 R609 H R617 C619 TL2648 R608 TL2643 R613 TL2691 R642 C612 TL2692 TL2667 TL2654 TL2652 TL2642 TL2646 C614 R643 TL2673 IC601 F TL2686 R638 TL2690 R622 C626
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E CARD PWB SIDE A J I H G SC1501 F E D 1 SW1501 C B A 1 2 3 4 5 6 132 7 8 9 10
1 2 3 4 5 133 C1502 R1506 6 7 C1505 R1501 C1504 R1513 Q1502 C1501 R1512 R1508 C1503 C1510 TL1504 R1509 TL1505 R1510 TL1501 TL1514 Q1501 C1509 R1514 Q1503 TL1506 R1507 TL1507 TL1508 F TL1509 TL1510 TL1503 TL1515 G TL1513 TL1512 E TL1511 SC1502 TL1502 VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E SIDE B J I H C1508 R1505 R1504 C1507 R1503 R1511 R1502 C1506 D C B A 8 9 10 0
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E INVERTER PWB J SIDE A I TL9810 BAT9802 1 TL9809 SC9802 TL9817 TL9815 C9812 BAT9801 H TL9813 T9800 R9808 TL9804TL9805 TL9818 R9809 TL9816 C9810 TL9814 TL9801 SC9801 R9804 G Q9801 C9809 C9802 L9801 TL9800 C9800 C9807 TL9803 R9803 TL9808 F SIDE B E D C 0 SW9800 B A 1 2 3 4 5 6 134 7 8 9 10
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E OPERATION PWB J SIDE A I 1 H SC2001 G F E SIDE B D R2003 R2002 0 TL2004 SW2001 R2001 RMC2001 SW2002 C2001 SW2003 TL2002 C TL2006 TL2005 B A 1 2 3 4 5 6 135 7 8 9 10
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E CCD PWB J SIDE A I C109 TL103 H R107 R104 TL102 TL104 TL108 TL107 TL109 C9 TL1 C8 TL105 G TL14 TL110 TL2 TL3 TL111 C16 TL112 TL12 TL113 F TL13 TL106 TL101 TL20 TL11 TL18 C12 TL8 C11 TL10 C15 0 TL115 TL4 R9 R1 TL114 C13 R8 Q1 TL17 TL9 E R2 C14 TL6 D1 TL7 TL5 D C B A 1 2 3 4 5 6 136 7 8 9 10
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E J SIDE B C108 C104 R103 C102 C105 I H C103 C110 IC101 G C106 R101 SC101 R106 C107 R102 C111 C112 IC1 R108 R105 F E 1 C101 D L101 C B A 1 2 3 4 5 6 137 7 8 9 10
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E HEAD AMP PWB J Component Side SIDE A I TL301 Q302 R318 C324 R312 R323 C319 C311 R325 C333 Q303 C327 R324 C332 C323 P306 R314 R319 SC306 C340 C306 TP323 TP324 C321 C344 C318 C314 C312 C343 C309 C301 C342 R377 R315 R304 C313 C302 R317 C305 C320 C315 R331 R333 C322 C331 C330 IC301 C307 H R332 R330 TL303R311 TL302 R310 C308 R309 R316 R313 C310 R321 R308 C304 R320 SC304 SC301 G SC303 SC305 F E Wiring Side SIDE A D C B A 1 2 3 4 5
G 1 2 3 4 5 139 6 7 L301 8 TP340 TP338 C329 R380 TP336 TP366 TP365 TP352 TP364 TP363 TP356 TP362 TP361 TP360 TP359 TP357 TP358 TP339 TP335 TP345 TP343 TP337 TP346 TP341 TP347 TP342 TP349 TP348TP344 IC302 TP355 TP351 TP353 TP354 C345 TP309 TP301 TP308TP310 TP313 TP317 TP314 TP312 TP311 TP321 TP320 TP319 TP318 TP316 TP322 TP325 TP327 TP326 TP328 TP315 TP334 TP332 TP331 TP330 TP350 H TP329 TP333 TP304 TP306 TP307 TP302 TP303 TP305 VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E J Compon
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E DC JACK PWB J SIDE A D2900 I 0 J2900 H G F SIDE B E D P2900 C L2900 B A 1 2 3 4 5 6 140 7 8 9 10
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E Part No. ★ Description LIST/ Code 16. REPLACEMENT PARTS EXPLODED VIEWS Ref. No. Ref. No. Parts marked with " å " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set. " HOW TO ORDER REPLACEMENT PARTS" ★MARK : SPARE PARTS-DELIVERY SECTION:ALL JAPAN 2. REF. NO. 4.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E Ref. No. VL-SD20U Part No. ★ Description Ref. No.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E Ref. No. L923 L1401 L1431 L1450 L1451 L1452 L1601 L1701 L1702 L2800 L2801 L2802 L2804 L3401 L3404 L3405 L3701 L4404 L4406 L4451 L4471 L7400 L7800 L7810 å T900 Part No.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E Ref. No. C906 C907 C908 C910 C911 C912 C913 C914 C915 C916 C917 C918 C919 C920 C921 C922 C923 C924 C926 C927 C928 C930 C931 C932 C933 C934 C936 C937 C938 C939 C941 C943 C946 C948 C949 C951 C952 C953 C954 C955 C956 C957 C959 C960 C962 C963 C964 C965 C966 C967 C968 C969 C970 C971 C972 C973 C974 C980 C982 C983 C990 C991 C992 C993 C1201 C1401 C1403 C1404 C1405 C1406 C1431 C1436 Part No.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E ★ Ref. No. Part No.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E Ref. No. VL-SD20U ★ Part No.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E Ref. No. R736 R737 R738 R739 R741 R742 R743 R744 R745 R746 R747 R748 R749 R750 R751 R752 R753 R754 R755 R756 R759 R760 R761 R762 R763 R764 R765 R766 R767 R771 R772 R779 R780 R782 R796 R797 R902 R903 R904 R905 R906 R907 R908 R909 R910 R912 R913 R914 R917 R918 R919 R920 R924 R926 R927 R928 R929 R930 R931 R933 R934 R935 R936 R937 R938 R939 R940 R941 R942 R943 R946 R948 R949 R950 R951 Part No.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E Ref. No. R1715 R1716 R1717 R1718 R1719 R1720 R1721 R1722 R1723 R1724 R1725 R1726 R1727 R1728 R1729 R1911 R1912 R1913 R1914 R1925 R1927 R1929 R1930 R1931 R1940 R1941 R1943 R1944 R1945 R1950 R1956 R1957 R1958 R1959 R1968 R1969 R1980 R1981 R1982 R1983 R1984 R1985 R1986 R1989 R1990 R1991 R1992 R1994 R1995 R1996 R1997 R1998 R2801 R2802 R2803 R2807 R2811 R2812 R2813 R2814 R2815 R2818 R2819 R2820 R2821 R2822 R2823 R2824 R2825 R2829 R2830 R2831 R2833 R2835 R2840 Part No.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E Ref. No. R3482 R3486 R3487 R3488 R3489 R3492 R3493 R3495 R3496 R3499 R3701 R3702 R3703 R3704 Part No.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E Ref. No. VL-SD20U ★ Part No. R7828 VRS-CZ1JF000J FB201 FB202 FB203 FB204 FB408 FB456 FB900 FB901 FB2801 FB3701 RBLN-0049TAZZ RBLN-0049TAZZ RBLN-0049TAZZ RBLN-0102TAZZY RBLN-0242TAZZY RBLN-0102TAZZY RBLN-0119TAZZ RBLN-0119TAZZ RBLN-0028TAZZ RBLN-0049TAZZ Description 0 ★ Code Ref. No.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E Ref. No. ★ Part No. R569 R570 R571 R572 R573 R574 R575 R576 R577 R578 R579 R580 R581 R582 R583 VRS-CZ1JF154J VRS-CZ1JF562J VRS-CZ1JF153J VRS-CZ1JF223J VRS-CZ1JF223J VRS-CZ1JF222J VRS-CZ1JF274J VRS-CZ1JF122J VRS-CZ1JF472J VRS-CZ1JF181J VRS-CZ1JF181J VRS-CZ1JF272J VRS-CZ1JF274J VRS-CZ1JF272J VRS-CZ1JF471J P51 P52 SC21 SC53 SC551 QPLGN0276TAZZ QPLGN0274TAZZ QSOCN3311TAN1 QCNCW3396TAZZY QSOCN2498TAZZY Description 150k 5.6k 15k 22k 22k 2.2k 270k 1.2k 4.7k 180 180 2.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E Ref. No. VL-SD20U ★ Part No.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E Ref. No. ★ Part No. SW2001 QSW-K0100TAZZ SW2002 QSW-K0100TAZZ SW2003 QSW-K0100TAZZ Description Switch Switch Switch Code Ref. No. ★ Part No.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E Ref. No. Part No. R324 R330 R332 R333 R377 R380 VRS-CZ1JF222J VRS-CZ1JF563J VRS-CZ1JF102J VRS-CZ1JF222J VRS-CZ1JF000J VRS-TV1JD100J P306 SC301 SC303 SC304 SC305 SC306 QCNCM8082TAZZ QSOCN0925TAN1 QSOCN1006TAN1 QSOCN0706TAN1 QSOCN2071TAZZ QSOCN1871TAZZ VL-SD20U ★ Description 2.2k 56k 1k 2.2k 0 10 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide Ref. No.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E Ref. No. Part No.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E Ref. No. Part No.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E Ref. No. 30 30 30 30 Part No. ★ TLABMA015WJZZ TLABMA016WJZZ TLABMA017WJZZ TLABMA018WJZZ 30 30 TLABMA022WJZZ TLABMA050WJZZ 30 TLABMA051WJZZ 31 GCOVA1874TASA a c d e g h i k m o p q r t u LX-HZ0050TAFN XiPSN17P03000 LX-BZ0221TAFC XiPSN17P02000 LX-BZ0238TAFN XiPSF17P02000 XiPSF17P03000 LX-BZ0251TAFD LX-BZ0253TAFN XiPSN17P06000 LX-HZ0063TAFN LX-HZ0050TAFF XiPSN17P04000 LX-BZ0224TAFN LX-BZ3201GEFF Description Code Ref. No.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E Ref. No. Part No. VL-SD20U ★ Description Ref. No. Code ACCESSORIES (NOT REPLACEMENT ITEM) TGANE0050TAZZ TGANE0057TAZZ TGANL0004TAZZ TLABK0001TAZZ Guarantee Card — (NZ50E(Australia, New Zealand)/ NZ100E(Australia, New Zealand)) Guarantee Card — (NZ50H/NZ80H/NZ100H) Guarantee Card — (NZ50S/H/NZ80H/NZ100S/H) No.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E MECHANISM CHASSIS Ref. No. Part No. ★ EXPLODED Description VIEW Code Ref. No. ★ Part No. 429 600 383 402 435 313 436 338 341 335 435 434 332 324 352 458 393 435 394 385 376 502 432 d 466 331 F 420 401 374 391 a 434 330 357 375 390 a 391 402 b 344 b 436 470 425 353 E 397 356 339 426 383 411~ 415 1 pc. 428 381 403 457 337 382 351 354 c 431 340 342 G 392 432 456 1pc.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E VL-SD20U LENS EXPLODED VIEW Ref. No.UNIT Part No. ★ Description Ref. No. Code ★ Part No.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E CABINET EXPLODED Ref. No. Part No. ★ VIEW Description Code Ref. No. 14-2 i 14-5 H ★ Part No.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E VL-SD20U CASSETTE CONTROL VIEW Ref. No. Part No. ★ EXPLOOD Description Ref. No. Code ★ Part No. Description 434 D 600 602 610 4±0.5 604 8.5±0.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E VL-NZ50S/H/E/W/NZ80H/NZ100S/H/E SERVICE JIG SPECIFICATIONS Ref. No. Part No. ★ Description Code Ref. No. Part No. 1-1. Adjusting jigs for checking the mechanism No. Name New part ★ Type number, Application 1mN·m/1.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E VL-SD20U Ref. PACKING No. Part No. ★ Description 17. OF THE SET Ref. No. Code Part No. ★ Description Code NZ50H/W(Hong Kong)/NZ80H/ NZ100H/E(Hong Kong)) model No.11 No.1 No.18 No.10 No.14 No.13 No.1 No.8 No.7 No.25 No.2 No.24 No.9 No.6, No.15, No.16, No.17, No.19 No.3 No.5 No.22 No.26 No.27 No.28 No.23 No.4 No.20 No.21 ACCESSORIES No.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E Ref. No. Part No. ★ Description Code Ref. No. 165 Part No.
VL-NZ50S/H/E/W/NZ80H VL-NZ100S/H/E Ref. No. Part No. VL-SD20U ★ Description Ref. No. Code ★ Part No. Description Code COPYRIGHT C 2002 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.
