VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E SERVICE MANUAL S32G4VL-A111S SERVICE MANUAL LIQUID CRYSTAL CAMCORDER Hi 8 PAL LIQUID CRYSTAL CAMCORDER Hi 8 VL-A111S/H/E VL-AH131S/H/E MODELS VL-AH151S/H/E In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified be used. CONTENTS PAL MODELS VL-A111S/H/E/AH131S/H/E/AH151S/H/E Page 1. SPECIFICATIONS .........................................
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 1. SPECIFICATIONS Signal System: PAL standard Recording System: 2 rotary heads, helical scanning system Cassette: A111S/H/E: 8 mm video tape, MP type AH131S/H/E/AH151S/H/E: 8 mm video tape, MP type or Hi8 MP, ME type Recording/Playback Time: 120 minutes (P5-120) Tape Speed: 20.051 mm/second Pickup Device: 1/4" (6.4mm, effective size: 4.5 mm) CCD image sensor (with approx. 320,000 pixels including optical black) Lens: 16 × power zoom lens (F1.4, f=4.0-64.
Speaker Microphone 3 Cassette compartment door Lens hood Lithium battery holder Shoulder strap loop DC IN jack AUDIO jack VIDEO jack Terminal cover Cassette compartment door release Cassette holder When the cassette compartment door is open Zoom lens Front view Battery compartment door Bottom view Hand strap FADE button Battery compartment door release Power switch (CAMERA/VCR select switch) Tripod socket DISPLAY button Operation buttons MENU button CHARGE indicator Shoulder strap
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 3. DISASSEMBLY OF THE SET 3-1. REMOVAL OF THE CAMERA SECTION Note: Before removing the cabinet, turn off the power supply, and ascertain that the battery has been removed. (b) Connector (b) Pull out (a) (1) Camera front cabinet (d) (a) 5. Remove the connector of the 6-cell detection switch, and remove two screws ((b)LX-HZ0018TAFF) fixing the battery catcher. 1.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 3-2. DISASSEMBLY OF THE VCR MAIN BODY <1. Removal of the VCR lid shaft> Area A (b) (k) (2) Remove five screws ((b)LX-HZ0018TAFF). (1) Remove one screw ((k)LX-HZ0063TAFN).
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E <3. Removal of the VCR lid> Caution for installation of the VCR lid Microphone connector VCR lid Area B When installing the VCR lid, move the VCR lid in the arrow direction, keeping the VCR lid parallel to the main body as shown above. (1) Disconnect the microphone connector. <4.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E <8. Removal of the Lithium PWB> (b) LCD unit Lithium PWB Main PWB Connector Connector Inverter transformer (3) Remove two screws ((b)LX-HZ0018TAFF) and two connec- (1) Remove the connector of the Lithium PWB from the Main PWB. tors, and remove the LCD unit (with inverter) from the main (2) Move the lithium unit in the direction of the arrow. body. <9. Disassembly of the frame V> <6.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E Claw C Claw B View E Claw A Claw D View F Note: When fixing the cassette compartment lid, first engage the claws A and B, and then engage the claws C and D, confirm that the four claws (A, B, C and D) of the cassette compartment lid are securely engaged as shown in the view above. <11.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 3-3. REPLACEMENT OF CCD SENSOR 3-3-1. BEFORE REPLACEMENT 1) The CCD image sensor is more sensitive to electrostatic breakage than C-MOS LSI. Therefore sufficient means to prevent electrostatic damage must be taken when it is replaced. • Ground the soldering iron. • Ground also the human body, using the wrist strap(through an 1 Mohm resistor). • Until the CCD sensor is mounted on the PWB, fit it to the conductive sponge, and short-circuit the foot lead.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 4. MECHANISM ADJUSTMENT 4-1. MECHANISM CHECKING/ADJUSTING JIGS, TOOLS AND PARTS 4-1-1. Mechanism checking/adjusting jigs and tools 1. Cassette torquemeter for PB 2. JiG8T-012 3. CV * (10 g·cm/25 g·cm) 1. Cassette torquemeter for VS-REW 2. JiG8T-032 3. CV * (50 g·cm/25 g·cm) 1. Torque gauge 2. JiGTG0045 3. CN * For measurement of loading brake torque Configuration 1. Name 2. Part No. 3. Code * Model, Application 1. Torque gauge head 1.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 4-2. ITEMS AND TIMINGS OF INSPECTION AND MAINTENANCE The mechanism of VCR needs the following periodic inspection and maintenance in order that it maintains its high quality. Also, after the machine is repaired, execute the following maintenance and checks regardless of how long it has been used. 4-2-1. Inspection and maintenance list Checking/Maintenance point 500 Used time (hrs.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 4-3. MECHANISM CHECKS AND ADJUSTMENTS The description given below relates to the general field services, but does not relate to the adjustment and replacement that require high level equipment, jigs, and technical skills. In order to maintain the initial characteristics of the machine, it is necessary to execute the maintenance and check and to prevent damage to tapes and other parts. For adjustments which need jigs, be sure to use the jigs.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 4-3-4. Checking and adjusting the tension pole position (1) Check When it begins to wind the P5-120 tape check whether the tension pole is in the specified position to the Si roller as shown in the figure. If it is not in the specified position, remove the cassette and adjust the position in the following procedure. (2) Adjustment 1. Don’t set up any tape, and select the PB mode. (Refer to Item 4-5-1-(4).) 2.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 4-4. ADJUSTMENT OF MECHANISM TAPE RUNNING SYSTEM Sup tilted pole 4-4-1. Preparation for adjustment Sup GR (1) Clean the tape running areas (guide poles, rollers, drum, Capstan shaft, Pinch roller) (Figure 1) Si roller (2) Connect the oscilloscope to the following TPs. RF output ..... TL7410 H-SW-P ....... TL7417 GND ............. TL7413 (3) Playback the alignment tape (VR2DB0PS). Tension pole (4) Ascertain that each guide is free from remarkable curl.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 4-4-4. Adjusting the Tu guide Height setting jig Master plane (JiGMP-MX7U) Upper flange After replacement of Tu guide preset and adjust the height. (1) Tu guide height presetting (Figure 6) Adjust the height from the upper surface of mechanism chassis to the upper surface of lower flange with the aid of jig. Lower flange Figure 6 (2) Adjusting the Tu guide (Figure 7) 1 Playback the alignment tape (VR2DB0PS).
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 4-5. MECHANISM ASSEMBLING AND PARTS REPLACEMENT (DISASSEMBLING AND ASSEMBLING) Below is given an explanation of assembling of mechanism and its parts replacement. The removal of cabinet and the PWB is explained in the relevant service manual. Notes 1 After removal of cut washers be sure to replace them with new ones. 2 Do not place the mechanism upside down on the table. Otherwise, the mechanism part may be deformed or damaged, resulting in malfunction.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 4-5-2. Cassette control ass’y Lock Lever (1) Set the unit to the EJECT mode, and let the housing stand upright. Or set the unit to the STANDBY mode, press the lock lever in the arrow direction, and let the housing stand upright. (See Fig. 5: in the direction a or b ) (When pushing in the direction a , slightly lift the housing by hand to release the lock lever.) (2) Remove the four screws 2 and take out the down guide 3.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 4-5-5. Phase matching The phase of the following parts must be matched as shown in the figure below. (Ascertain that the marks and round holes align.) (1) Lo relay gear (3) Sub-cam (2) Main cam (4) Mode switch Lo relay gear Phase matching mark (Round hole) Mode switch Phase matching mark ( Mark) Phase matching mark (Round hole) 4-6. MECHANISM ASSEMBLING METHOD (1) Adjust the phase of each part. (2) Install screws and washers.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E (7) Install the guide rail assembly taking care to position it (4) Install the loading block assembly and the capstan motor. correctly. (5) Install the drive gear. At this time, pay attention to the direction of gear. (The small gear must be located in the B A chassis side.) a a A a Make sure not to deform the arm. Loading motor Capstan motor a A a D C Move FF downwards Install the motor under this plate.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E (8) Install the drum assembly in the chassis. (9) Install the tape guide in the drum assembly. (10) Install the Si roller. (11) Install the slide chassis. T arm guide B Tape guide A Slide this part towards the T arm. Place the slide chassis on the guide rail. A Drum assembly B A A Si roller B Roller spring Main cam pin B Insert the main cam pin into the hole of cam of slide chassis. Sup reel base Item A M1.4 x 1.5 ø4.5 B M1.4 x 1.5 ø3.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 5. ADJUSTMENT OF THE ELECTRICAL CIRCUITS 5-1. BEFORE ADJUSTMENT · Electric circuit adjustment becomes necessary, in most cases, when any of the wear mechanical parts or the video head has been replaced. Before starting the electric circuit adjustment, be sure to check that the mechanical parts work well (i.e., the mechanical parts have all been perfectly adjusted).
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 5-3-4. Setting value Table 1) When IC705 is replaced VTR ADJ ADD.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 5-4. TEST mode TEST No. Title 1 Sensor Off 2 3 4 5 6 7 8 Mecha Adjustment mode Shut Off Adjustment Error Display PASS mode Cam Adjustment mode VCR Adjustment mode Head Switching Point ADJ. Contents All the sensors are off except for the cassette control switch, DEW sensor, and battery sensor. ATF sampling is restricted to the central part. Shutoff voltage value is written in E2PROM.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 1 2 3 4 5 1. Extension Cable Inverter~VCR (7pin) 2. QCNW-1265TAZZ 3. AX 1. Extension Cable 1. Extension Cable 1. Extension Cable 1. Extension Cable LCD~ MECHA~VCR (70pin) Camera~VCR (20pin) Camera~VCR (24pin) VCR (24pin) 2. QCNW-1534TAZZ 2. QCNW-1774TAZZ 2. QCNW-1382TAZZ 2. QCNW-1382TAZZ 3. BS 3. BH 3. BD 3. BD 6 7 1. Operation Unit 2. QSW-Z0287TAZZ or RUNTKA010WJZZ 3. AW/AS 1. AV Jack Unit 1. Battery Terminal Unit 2.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 5-6-3. VCR circuit adjustment * Before adjusting the VCR circuit, make sure that the fixed value in 5-3-2 is written in E2PROM. · Test points on the video circuit board. 5-6-3-1. Supply voltage adjustment/check POWER CIRCUIT ADJUSTMENT PROCEDURE Turn on power û 1. Adjust to CAM 15V û 2. Check P-CON 4.9V û 3. Check P-CON 3.3V û 4. Check P-CON 3.1V û 5. Check DSP 2.65V û 6. Check DSP 1.85V û 7. Check LCD 13.2V û 8. Check LCD 7V û 9. Check LCD -15.2V û 10.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 5-6-3-2. Head Switching Point Adjustment 1) Play back the alignment tape (JiGWR5-5CSP) Measuring instrument 2) Press the “CONTINUE” key and “TEST SEL.” key on the adjustment remote control to set the test mode. Mode (At this time the numeral of “T-01” blinks.) Adjustment address 3) Using the “FF” and “REW” keys, select “T-08”, and press Tape "PLAY" key to set the SW-P adjustment mode. 4) When the adjustment is completed, "HSWP" is displayed and the tape is ejected.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 5-6-3-4. Adjustment of audio circuit 1. Adjustment of filter f0 Measuring instrument Oscilloscope Mode PB Input signal (tape) JiGWR5-5CSP Measuring terminal TL605/AUDIO.OUT Adjustment address 33 (VTR ADJ) Set value Clear the waveform 1) Set the alignment tape (JiGWR5-5CSP). 2) Using the adjustment remote control (RRMCG0033TASA), set the VCR adjustment mode, and set the address “33” with the operation switch ("FF", "REW" key). 3) Play back the standard tape.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 5. VCO adjustment Measuring point Address(VTR ADJ) Mode Adjusting method TL3802 03E VCR 1) Connect TL3803 to GND. 2) Connect the frequency counter to TL3802, and adjust the frequency. Adjustment standard 15.625kHz ± 100Hz Remarks ——————— 6. H-position adjustment Measuring point TL3802 Address(VTR ADJ) 03B Mode VCR Adjusting method 1) Connect the oscilloscope to TL3802, and adjust the pulse width. t V Adjustment standard 2.8µsec ±0.15µsec Remarks ——————— 7.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 5-7. CAM section adjustment 5-7-1. CAM section adjustment jigs (1) Object, measuring instrument and jigs necessary for camera section servicing • • • • • Gray scale chart Vectorscope Extension cable Oscilloscope Video output cable • Color bar chart • Color temperature conversion filter HOYA "LB-165" • Digital voltmeter • • • • Halogen light (2 pcs.) Color video monitor AC adapter Service Remote Control Configuration 1. Name 2. Part No.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 5-7-3. CAM circuit adjustment * Before adjusting the CAM circuit, make sure that the fixed value in 5-3-3 is written in E2PROM. 5-7-3-1. Supply voltage check Check that the voltages at the following TL are within the specified range (refer to the supply voltage adjustment/check under VCR circuit adjustment). Measuring point TL0137 TL0138 TL0140 Item P-CON_4.9V P-CON_3.1V P-CON_5.7V SPEC 4.9V 3.1V 5.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 5-7-3-6. Black balance, AF noise level adjustment Mode CAM ADJ Measuring instrument — Subject Not specified Measuring point — Adjustment address 71 Adjustment reference 01 1) Write ADD:71 DATA:01. 2) Press the “STOP” key to reconfirm ADD “71”. Adjustment is completed when “FF” is returned to DATA. 5-7-3-7.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 5-8. TROUBLE SHOOTING 5-8-1. Classification of troubles No operation at all Check the Power circuit and system control circuit. û YES Check the system control and loading motor circuit. û YES Check the inverter transformer and power circuit. û YES * Check the camera section and Y/C circuit and LCD circuit. û YES Check the Y/C circuit and head amplifier circuit. û YES Check the Y/C circuit and head amplifier circuit.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 5-8-2. Troubleshooting for the camera section No picture Check the lens drive circuit (IC551) and main signal line. û YES Check IC401 (DSP), and its peripherals. û YES Check IC706 (camera CPU part of I chip µ-computer), IC551 (Lens driver) and their peripherals. û YES Check IC706 (camera CPU part of I chip µ-computer), IC551 (Lens driver) and their peripherals. û YES Check IC706 (camera CPU part of I chip µ-computer), IC551 (Lens driver) and their peripherals.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 6. BLOCK DIAGRAMS 6-1. SYSTEM BLOCK DIAGRAM BATTERY NONREGE IC701 IC900 POWER (CAMERA) 3.0V Reg Power Control IC POWER (SYS 3.0V) POWER (AT 3.
6, 7 36 5 1 IC101 BUFFER Q1403 BUFFER 24 22 20 LCD_VR LCD_VG LCD_VB 8 IC800 BUFFER LPF 6 C-FILTER Y-FILTER CDS AGC / ACC CDS_AGC Q1404/Q1406 CCD9CK CCD14CK PANEL IC1451 BUFFER AMP 25, 26 3, 5, 17, 18 V-DRIVER 13 CCD_OUT 4 Q1 VIDEO DRIVER Q2407 HPF Q2405 LPF VIDEO-OUT Q2401 NOISE CANCEL BLOCK ATT LIMITER 27 10 IC11 CCD SENSOR TIMING GENERATOR Q2402/Q2403 IC12 40, 42 LENS SY-IN SC-IN 8 LPF 7 LPF 8 BUFFER Q1401 BUFFER Q1402 V_SIGNAL 39 IC151 C
5 1 IC101 BUFFER Q1403 BUFFER 24 22 20 LCD_VR LCD_VG LCD_VB 8 IC800 BUFFER LPF 6 C-FILTER Y-FILTER CDS AGC / ACC CDS_AGC Q1404/Q1406 CCD9CK CCD14CK PANEL IC1451 BUFFER AMP 25, 26 3, 5, 17, 18 V-DRIVER 13 CCD_OUT 4 VIDEO DRIVER Q2407 10 IC11 HPF Q2405 LPF VIDEO-OUT Q2401 NOISE CANCEL BLOCK ATT LIMITER 27 TIMING GENERATOR 40, 42 Q2402/Q2403 IC12 6, 7 CCD SENSOR Q1 8 LPF 7 LPF 8 BUFFER Q1401 BUFFER Q1402 V_SIGNAL 39 A/D Converter C_OUT Y_OUT B
36 5 1 IC101 BUFFER Q1403 BUFFER 24 22 20 LCD_VR LCD_VG LCD_VB 8 IC800 BUFFER LPF 6 C-FILTER Y-FILTER CDS AGC / ACC CDS_AGC Q1404/Q1406 CCD9CK CCD14CK PANEL IC1451 BUFFER AMP 25, 26 3, 5, 17, 18 V-DRIVER 13 CCD_OUT 4 VIDEO DRIVER Q2407 10 IC11 HPF Q2405 LPF VIDEO-OUT Q2401 NOISE CANCEL BLOCK ATT LIMITER 27 TIMING GENERATOR 40, 42 Q2402/Q2403 IC12 6, 7 CCD SENSOR Q1 8 LPF 7 LPF 8 BUFFER Q1401 BUFFER Q1402 V_SIGNAL 39 A/D Converter C_OUT Y_OUT B
6, 7 36 5 1 IC101 BUFFER Q1403 BUFFER 24 22 20 LCD_VR LCD_VG LCD_VB 8 IC800 BUFFER LPF 6 C-FILTER Y-FILTER CDS AGC / ACC CDS_AGC Q1404/Q1406 CCD9CK CCD14CK PANEL IC1451 BUFFER AMP 25, 26 3, 5, 17, 18 V-DRIVER 13 CCD_OUT 4 Q1 VIDEO DRIVER Q2407 10 IC11 HPF Q2405 LPF VIDEO-OUT Q2401 NOISE CANCEL BLOCK ATT LIMITER 27 TIMING GENERATOR 40, 42 Q2402/Q2403 IC12 LENS CCD SENSOR SY-IN SC-IN 8 LPF 7 LPF 8 BUFFER Q1401 BUFFER Q1402 V_SIGNAL 39 IC151 C
6, 7 36 5 1 IC101 BUFFER Q1403 BUFFER 24 22 20 LCD_VR LCD_VG LCD_VB 8 IC800 BUFFER LPF 6 C-FILTER Y-FILTER CDS AGC / ACC CDS_AGC Q1404/Q1406 CCD9CK CCD14CK PANEL IC1451 BUFFER AMP 25, 26 3, 5, 17, 18 V-DRIVER 13 CCD_OUT 4 Q1 VIDEO DRIVER Q2407 HPF Q2405 LPF VIDEO-OUT Q2401 NOISE CANCEL BLOCK ATT LIMITER 27 10 IC11 CCD SENSOR TIMING GENERATOR 40, 42 Q2402/Q2403 IC12 LENS SY-IN SC-IN 8 LPF 7 LPF 8 BUFFER Q1401 BUFFER Q1402 V_SIGNAL 39 IC151 C
CH4 output Drive circuit (Rise and fall voltage) CH5 output Drive circuit (Voltage drop) CH4 ERROR AMP. IN- Comparator section CH5 ERROR AMP. IN- Comparator section 3 4 5 40 8 Standard power CH8 ERROR AMP. IN- Comparator section IN+ 7 B/L CTL CH7 ERROR AMP. IN- Comparator section IN+ CAP ERROR 6 CH8 output Drive circuit (NPN) CH7 output Drive circuit (Rise and fall voltage) CH6 output Drive circuit (Voltage drop) CH3 output Drive circuit (Rise and fall voltage) CH3 ERROR AMP.
LED Green DC JACK input 41 LED_R LED_G LED Red Charging : Red light up Completion : Green light up with JACK : OPEN with out JACK : GND Short circuit VDC<8V Voltage detective circuit 1 SW1 EXT Vcc 2 SW2 Charge control IC 7 8 Q2901 CS 5 3 LV 4 GND MM1332G CEL 6 ADP-DET Q2903 NON REG T PRE-CHARGE-ON CHARGE-ON_H Ni-MH battery BATT.-DET Q2903 with FET is always "OFF" at DC input.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 6-5. LENS DRIVE BLOCK DIAGRAM IC1 CCD SENSOR ZOOM LENS MASTER LENS IC101 CDS AGC IC151 A/D IC401 DSP 42 41 DATA 49 48 IC706 LENS DATA2 CS 2 12 SYSTEM CONTROL DATA CLK 3 IRIS, FOCUS, ZOOM CONTROL 4 124 MASTER LENS POSI 21 IRIS METER IC553 4.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E -MEMO- 43
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 7. SCHEMATIC DIAGRAMS 7-1.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 7-2.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 7-3.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 7-4.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 7-4.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 7-5.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 7-6.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 7-6.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 7-7.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 7-8.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 7-9.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 7-10.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 7-11.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 7-12.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 7-13.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 7-13.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 7-14.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 7-15.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 7-16.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 7-17.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 7-18.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 7-19.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E 8.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E VCR PWB Wiring Side SIDE A J I H G F E D C B A 1 2 3 4 5 6 89 7 8 9 10
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E VCR PWB Component Side SIDE B J I Q2905 D901 C907 Q907 D2913 D903 FB151 C916 C920 Q911 C943 FB152 R151 C917 D902 C948 Q925 D914 C947 Q921 C935 SC151 C1929 R1942 C164 R196 R186 TL181 TL188 R179 R180TL182 R182 R183 TL185 TL1801 R930 TH3800 TL915 R931 C946 C952 IC904 R3806 R3805 C3818 R3853 C3819 R729 R713 R728 R712 R727 R711 R726 R710 R725 R709 R724 R708 R723 R707 R743 TL189 TL183 TL903 TL184 TL3801 R3854 SC152 R19
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E VCR PWB Wiring Side SIDE B J I H G F E D C B A 1 2 3 4 5 6 91 7 8 9 10
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E CAMERA PWB Component Side SIDE A J TL556 TL557 TL559 TL560TL565 TL566 TL567 TL568 TL570 P101 Z1 TL100 C113 C108 L101 C111 TL101 I SC551 TL552 TL554 TL558 TL551 TL553 TL555 TL11 TL12 TL13 TL14 TL15 C563 TL25 TL29 TL115 TL113 TL111 TL128 R140 R123 R124 TL121 R126 R134 R133 R127 C38 L13 TL122 R31 TL104 FB102 R29 TL105 FB103 R109 Q13 R35 R41 SC101 TL107 TL108 FB106 TL129 TL124 Q15 Q14 R36 R37 C33 X11 FB105 R110 TL106 FB104 C C35 C
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E CAMERA PWB Wiring Side SIDE A J I H G F E D C B A 1 2 3 4 5 6 93 7 8 9 10
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E CAMERA PWB Component Side SIDE B J C574 C568 R563 R583 TL136 R148 TL135 IC553 R147 C106 C110 C112 C109 R106 C107 R107 R108 C573 TL102 TL148R120 C103 R101 R102 R122 TL149R121 C553 C104 R103 R105 R104 C105 R572 R585 C571 R586 R579 R587 C567 TL150 G P102 R570 C566 R569 R562 R571 C572 R568 C569 R567 R566 R565 IC552 R561 R564 R577 D551 H R581 R588 R576 R584 R578 C570 R575 I R582 R580 IC101 IC554 R589 TL147R119 TL143R115 C120 C15 C119
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E CAMERA PWB Wiring Side SIDE B J I H G F E D C B A 1 2 3 4 5 6 95 7 8 9 10
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E HEAD AMP PWB Component Side SIDE A C3707 C3708 J TL3705 IC3701 C3720 TL3732 C3725 C3727 R3723 C3728 TL3733 C3726 C3729 TL3701 TL3734 TL3725 TL3716 TL3727 TL3729 TL3728 TL3738 TL3736 R3727 R3726 TL3723 R3724 R3728 R3725 C3732 TL3724 TL3706 C3734 TL3719 C3730 C3731 R3729 TL3717 G C3733 TL3718 C3723 TL3726 C3724 R3719 TL3702 L3701 L3702 R3720 C3718 C3719 C3722 R3721 R3722 C3716 C3717 C3721 C3702 C3703 R3701R3705R3707 R3704 R3702 C37
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E HEAD AMP PWB Wiring Side SIDE A J I H G F E D C B A 1 2 3 4 5 6 97 7 8 9 10
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E HEAD AMP PWB Wiring Side SIDE B J I H G F E D C B A 1 2 3 4 5 6 98 7 8 9 10
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E Ref. No. Part No. ★ Description Ref. No. Code 9. REPLACEMENT PARTS LIST/ EXPLODED VIEWS Part No. Parts marked with " å " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E Ref. No. Part No.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E Ref. No. ★ Part No.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E ★ Ref. No. Part No.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E Ref. No. Part No.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E Ref. No. Part No.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E Ref. No. R933 R934 R935 R936 R937 R938 R939 R940 R941 R942 R943 R944 R945 R946 R947 R949 R951 R1403 R1404 R1407 R1408 R1409 R1410 R1411 R1413 R1416 R1452 R1453 R1454 R1455 R1458 R1803 R1806 R1807 R1808 R1809 R1810 R1812 R1813 R1814 R1815 R1816 R1817 R1818 R1819 R1820 R1821 R1901 R1902 R1903 R1905 R1906 R1907 R1908 R1909 R1910 R1911 R1912 R1913 R1914 R1915 R1916 R1917 R1919 R1920 R1921 R1922 R1923 R1924 R1925 R1926 R1927 R1929 R1930 R1931 Part No.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E Ref. No. Part No.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E Ref. No. R8404 R8407 R8412 R8413 R8416 R8417 R8418 R8419 R8421 R8422 R8451 R8452 R8453 R8454 R8455 R8456 R8457 R8458 R8459 R8460 R8461 R8462 R8463 R8464 R8467 R9410 ★ Part No.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E ★ Ref. No. Part No.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E Ref. No. ★ Part No.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E Ref. No. Part No.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E Ref. No. 6-12 6-13 6-14 7 7-2 7-3 7-4 7-5 8 9 10 11 12 å 13 14 15 17 17 17 17 Part No.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E Ref. No. Part No. ★ Description Ref. No. Code Part No.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E MECHANISM Ref. No. Part CHASSIS No. ★ EXPLODED Description VIEW Code Ref. No. ★ Part No.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E Ref. No. Part No. ★ VIEWDescription CABINET EXPLODED Ref. No. Code 3-2 k ★ Part No.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E Ref. No. Ref. No. Part No. ★ CONTROL Description Code CASSETTE HOUSING UNIT EXPLODED VIEW Part No. ★ Description Code 400 C 401 401 B A 1 2 3 4 5 6 CAMERA UNIT EXPLODED VIEW 5 D 6 2 4 3 C 1 The mark must be on the face. B Lens side CCD side Mark Face the thinner part toward the lens side.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E Ref. No. Part No. ★ Description 10. PACKING OF THE SET Ref. No. Code Part No. ★ Description Code A111H/E(Hong Kong), AH131H, AH151E(Hong Kong) model A111S/E(Asia), AH131S, AH151S/(Asia) No.19 No.19 No.2 No.2 No.2 No.14 No.28 No.4 No.13 No.12 No.5, No.6, No.7, No.8, No.9, No.10, No.11 No.20 No.26 No.25 No.3 No.30 No.21 No.17 No.15 No.1 No.27 No.16 No.18 No.23 No.29 No.23 No.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E Ref. No. Part No. ★ Description Ref. No. Code 117 Part No.
VL-A111S/H/E/AH131S/H/E VL-AH151S/H/E Ref. No. Part No. ★ Description Ref. No. Code ★ Part No. Description Code COPYRIGHT C 2002 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.
