System information
CMOS Setup / Boot Procedure
VSBC-6 Reference Manual Configuration / Operation – 7
CMOS Setup / Boot Procedure
• Turn power on.
• Press the DEL key the instant that video is displayed (during the memory test).
• Verify correct CMOS Setup information (see table below)
• Insert bootable floppy disk into floppy drive or allow the system to boot from the hard
drive.
Basic CMOS Configuration
+------------------------------------------------------------------------------+
| System Bios Setup - Basic CMOS Configuration |
| (C) 2000 General Software, Inc. All rights reserved |
+---------------------------+--------------------+-----------------------------+
| DRIVE ASSIGNMENT ORDER: | Date:>Jan 01, 1980 | Typematic Delay : 250 ms |
| Drive A: Floppy 0 | Time: 00 : 00 : 00 | Typematic Rate : 30 cps |
| Drive B: (None) | NumLock: Disabled | Seek at Boot : None |
| Drive C: (None) +--------------------+ Show "Hit Del" : Enabled |
| Drive D: (None) | BOOT ORDER: | Config Box : Enabled |
| Drive E: (None) | Boot 1st: Drive A: | F1 Error Wait : Enabled |
| Drive F: (None) | Boot 2nd: (None) | Parity Checking : (Unused) |
| Drive G: (None) | Boot 3rd: (None) | Memory Test Tick : Enabled |
| Drive H: (None) | Boot 4th: (None) | Test Above 1 MB : Disabled |
| Drive I: (None) | Boot 5th: (None) | Debug Breakpoints: (Unused) |
| Drive J: (None) | Boot 6th: (None) | Splash Screen : Disabled |
| Drive K: (None) +--------------------+-----------------+-----------+
| (Loader): (Unused) | IDE DRIVE GEOMETRY: Sect Hds Cyls | Memory |
+---------------------------+ Ide 0: Not installed | Base: |
| FLOPPY DRIVE TYPES: | Ide 1: Not installed | 640KB |
| Floppy 0: 1.44 MB, 3.5" | Ide 2: Not installed | Ext: |
| Floppy 1: Not installed | Ide 3: Not installed | 15MB |
+---------------------------+--------------------------------------+-----------+
Custom Configuration
+------------------------------------------------------------------------------+
| System BIOS Setup - Custom Configuration |
| (C) 2000 General Software, Inc. All rights reserved |
+---------------------------------------+--------------------------------------+
| COM1 (03F8) : Enabled | COM3 (03E8) Enable/IRQ : IRQ4 |
| COM2 (02F8) : Enabled | COM4 (02E8) Enable/IRQ : IRQ3 |
| Parallel Port Mode : SPP | LPT1 (0378) Enable/IRQ : IRQ7 |
| Ethernet Enable/Base : 340h | Ethernet IRQ (if enabled) : IRQ11 |
| Cache (L1 and L2) : Enabled | PCI INTA : IRQ10 |
| Interrupt Vector Restore : Disabled | PCI INTB : IRQ10 |
| I/O Register Base Address : 0E0h | PCI INTC : IRQ10 |
| 64KB Memory Page at E000 : None | PCI INTD : IRQ10 |
| Reserved : (Unused) | USB Controller Enable/INT : Disabled |
| IDE 0 PIO Mode : Auto | IDE 2 PIO Mode : Auto |
| IDE 1 PIO Mode : Auto | IDE 3 PIO Mode : Auto |
| | |
| | |
+---------------------------------------+--------------------------------------+
Shadow Configuration
+------------------------------------------------------------------------------+
| System BIOS Setup - Shadow/Cache Configuration |
| (C) 2000 General Software, Inc. All rights reserved |
+---------------------------------------+--------------------------------------+
| Shadowing : >Chipset | Shadow 16KB ROM at C000 : Disabled |
| Shadow 16KB ROM at C400 : Disabled | Shadow 16KB ROM at C800 : Disabled |
| Shadow 16KB ROM at CC00 : Disabled | Shadow 16KB ROM at D000 : Disabled |
| Shadow 16KB ROM at D400 : Disabled | Shadow 16KB ROM at D800 : Disabled |
| Shadow 16KB ROM at DC00 : Disabled | Shadow 16KB ROM at E000 : Disabled |
| Shadow 16KB ROM at E400 : Disabled | Shadow 16KB ROM at E800 : Disabled |
| Shadow 16KB ROM at EC00 : Disabled | Shadow 64KB ROM at F000 : Enabled |
+---------------------------------------+--------------------------------------+
Note! Due to changes and improvements in the system BIOS, the information on your
monitor may differ from that shown above.