VC-S2000HM VIDEO CASSETTE RECORDER OPERATIONAL MANUAL ● S-VHS PLAYBACK/RECORDING ● SUPER VHS ET (EXPANSION TECHNOLOGY) ● 16:9 PLAYBACK/RECORDING ● NEXTVIEW LINK ● NICAM Hi-Fi STEREO ● SATELLITE/CABLE BOX CONTROL ● AUTO SORTING & CLOCK SET ● SHARP SUPER PICTURE ● S-VIDEO CONNECTION ● VPS/PDC ● AUDIO DUBBING ● POWERSAVE FEATURE ● NTSC SIMPLE PLAYBACK ● CHILD LOCK S-VHS E T DELUXE
Dear SHARP Customer Thank you for buying this SHARP VCR. Given proper care it will provide years of entertainment for the whole family. Please read this operation manual carefully before attempting to operate the VCR. Copyright ● Audio-visual material may consist of copyrighted works which must not be recorded without the authority of the owner of the copyright. Please refer to the relevant laws in your country.
REMOTE CONTROL TIMER ON/OFF CHANNEL TV OPERATE 1 8. 1. 2. 4 23. 6 5 VOLUME DISPLAY 9. 7 8 0 16. - 4. 3D-DNR/TBC SUPER P. MENU 11. 5. ZERO BACK + SKIP SEARCH FF REW DPSS SLOW 15. 10. 25. 26. 27. 28. 29. 30. 31. INPUT SELECT AUDIO OUT 14. CHANNEL 3. 24. 9 AM/PM VCR STANDBY 22. 3 MODE OSD 13. INPUT SELECT 2 SET 17. PLAY/ X 2 6. 32. STOP CLEAR SHOWVIEW PAUSE /STILL TV/ VCR 33. 34. 35. 18. 12. 19. 7. REC. TAPE SPEED DIRECT TV REC A.
CONTENTS BEFORE USING YOUR VCR Important notes on your VCR ....................................................................................................... 2 Unpacking the accessories ........................................................................................................... 3 INSTALLING YOUR VCR Connecting the VCR to the TV, aerial and satellite receiver.................................................... 4 Alternative Connection .....................................................
BEFORE USING YOUR VCR IMPORTANT NOTES ON YOUR VCR IDEAL VCR LOCATION PLACE THE VCR.. • ... on a flat level surface away from radiators or other heat sources and out of direct sunlight. • ... and video tapes away from magnetic sources such as speakers or microwave ovens. • ... at least 8” (20cm) away from the TV. • ... away from curtains, carpets or other materials and allow ventilation space around the VCR. DO NOT... • ... block the air-vent openings. • ...
BEFORE USING YOUR VCR UNPACKING THE ACCESSORIES CHECK ALL THESE ACCESSORIES ARE SUPPLIED WITH YOUR VCR. CONTACT YOUR DEALER IF ANY ARE MISSING. TV OPERATE CHANNEL (TYPE AA/R6/UM3) BATTERIES (X2) REMOTE CONTROL for the remote control unit. RF CONNECTION CABLE connects the VCR to the TV. For a more detailed picture of your remote control refer to page (ii). TV/ VCR VIDEO CASSETTE RECORDER To fit the batteries into the remote control Remove the battery cover on the back of the remote control.
INSTALLING YOUR VCR CONNECTING THE VCR TO THE TV, AERIAL AND SATELLITE RECEIVER AERIAL OR CATV CABLE 1 Connect your existing aerial cable to the ANTENNA IN socket on your VCR. 3 Connect the VCR to the mains ANTENNA IN ENTREE ANTENNE G S-VIDEO OUT SORTIE SON S-VIDEO D RF OUT SORTIE ANTENNE 2 Optional: Connect your Satellite receiver or decoder to the VCR using a scart lead to LINE 2 IN/DECODER socket on the VCR. Connect your TV to the VCR using the supplied RF connection cable, i.e.
INSTALLING YOUR VCR ALTERNATIVE CONNECTION S-VIDEO The conventional input and output sockets of a VCR have the luminance signal (Y) and the colour signal (C) combined. This signal is then recorded onto the video tape. The S-Video Socket allows separate transmission of signals to enhance picture clarity during playback and record.
INSTALLING YOUR VCR AUTO INSTALLATION DIGITAL SATELLITE IF YOU WISH TO CONNECT YOUR VCR TO A SKY DIGIBOX RECEIVER GO TO “INSTALLATION OF A SKY DIGIBOX RECEIVER” SATELLITE RECEIVER / CABLE BOX CONTROL If you have a satellite receiver or cable box connected to your VCR you can automatically install the satellite channels using this feature. The installation procedure for cable boxes is the same as for satellite receivers (for cable box connections refer to your cable box manual).
INSTALLING YOUR VCR AUTO INSTALLATION PROCEDURE This model automatically tunes the TV channels for your area, then using Teletext information sorts the TV channels into a standard order and sets the clock. If the VCR has not previously been tuned-in, instructions will be given on screen to guide you through this procedure. 1. Ensure your VCR is still in the STANDBY mode. 2. Switch on the TV.
INSTALLLING YOUR VCR AUTO INSTALLATION 6. Ensure your AERIAL/SCART cable is connected to your VCR and then press SET to confirm 7. SAT CONTROL will be highlighted. • • If you do have a satellite receiver connected to the VCR continue from point 8. 7 SAT RECE I VER S A T CON T RO L If you do not have a satellite receiver connected to the VCR leave SAT CONTROL set to OFF and press SET. ON OF F The VCR will attempt to copy the TV preset list (NexTView compatible TV’s only).
INSTALLING YOUR VCR AUTO INSTALLATION 11. Press [ / ] to select SAT NO. Turn to the table at the end of this manual. Look for the make of your satellite receiver and use the NUMBER BUTTONS to enter the first code number listed. For example number 8 should be entered 0 0 8. Your satellite should now change to preset channel 12. 12. If your satellite receiver has changed to preset channel 12, press SET to confirm the VCR will automatically install both satellite and terrestrial channels.
BASIC OPERATION SCART LEAD CONNECTION (NOT SUPPLIED) A scart lead can be connected at any time. It is recommended to connect your TV and VCR in this way as it will provide improved picture and sound quality. Please refer to the connection diagram on page 4. IMPORTANT NOTES ON YOUR VCR AND VIDEO TAPES VIDEO TAPES • If you use only good quality video tapes, generally it will not be necessary to clean the video heads.
BASIC OPERATION HOW TO PLAYBACK A VIDEO TAPE • For double speed playback (without sound), press PLAY/X2 ( • To revert to normal playback, press PLAY/X2 ( • To stop the video tape, press STOP ( • To eject the tape press ) again. ) again. ). EJECT on the VCR. SHARP SUPER PICTURE SHARP SUPER PICTURE should enhance the picture quality during playback. It is normally set to ON. To turn SHARP SUPER PICTURE on or off press SUPER P. on the remote controll.
BASIC OPERATION HOW TO PLAYBACK A VIDEO TAPE FAST FORWARDING/REWINDING A VIDEO TAPE 1. Press STOP ( ) to stop the video tape. 2. Press FAST FORWARD ( )/REWIND ( ) on the remote control or on the VCR front panel. 3. To stop fast forward/rewind, press STOP ( ). FORWARD/REVERSE VISUAL SEARCH 1. During playback for continuous search mode, press FAST FORWARD ( REWIND ( )/ ) on the remote control, or on the VCR front panel. 2.
BASIC OPERATION IMMEDIATE RECORDING S-VHS ET (EXPANSION TECHNOLOGY) By selecting this function, your VCR will record a virtual S-VHS recording on a standard VHS format tape. This will help increase picture quality. This function will only work when S-VHS in the Mode Menu is selected to Auto and the VCR is in SP mode. • High Grade tapes are highly recommended for Super VHS E T recording.
BASIC OPERATION DIRECT TV RECORDING This feature can only be used with nexTView, Smart Link, Easy Link and Megalogic compatible tv’s. By pressing the DIRECT TV REC button on the remote control, the VCR will record the signal currently being displayed on the TV regardless of the signal source. This feature can be started when the VCR is in STANDBY or OPERATE mode. • If appears on the VCR display, press TIMER ON/OFF before starting. • Ensure a video tape is inserted into the VCR.
BASIC OPERATION HOW TO USE TO MAKE A RECORDING • If • Check that the clock is displaying the correct time. appears on the VCR display, press TIMER ON/OFF before starting. • Select either S-VHS AUTO or OFF in the Mode Menu for your preferred recording format. VIDEOPLUS+ allows you to program the VCR to record up to eight programmes using the VIDEOPLUS+ numbers published in TV listings... 1. Press PLUSCODE on the remote control 2.
BASIC OPERATION HOW TO USE TO MAKE A RECORDING 7. If your VCR has long play facility and you wish to change the RECORDING SPEED, use the [ / ] to highlight SP. Press [ / ] to select standard play (SP), long play (LP) or extended play (EP)as required. 8. [See NOTE below]. For VPS/PDC setting use [ / ] to highlight the final column. Using the [ / ] will select VPS/PDC ON or OFF (✱ = ON - = OFF).
BASIC OPERATION HOW TO SET A DELAYED RECORDING You can make a maximum of eight delayed recordings up to a year in advance. The example shown is for 24-hour clock operation. 12-hour clock operation can be selected from the manual clock setting menu. 12-hour clock am/pm can be selected using the AM/PM button on the remote control. • If appears on the VCR display, press TIMER ON/OFF before starting. • Check that the clock is displaying the correct time.
BASIC OPERATION HOW TO SET A DELAYED RECORDING 8. Enter the start time using the [ / ] or the NUMBER BUTTONS hours first then minutes (when entering less than 10 minutes add a '0' before the number), for example for 21:05 start, press 2 1 0 5. Then press SET to confirm. 9. Enter the stop time, for example for 22:30 stop, 1/2 DA T E P R S T AR T S T OP 21 / 06 02 12 : 00 13 : 00 - : - 9 / 0 7D0 3 2 1 : 0 5 - - / - - - - : - - : - - - / - - - - : - - : - - SP * SP * - - - - - press 2 2 3 0. 10.
BASIC OPERATION CHECKING, CHANGING AND CANCELLING A RECORDING Before you start! • If appears on the VCR display, press the TIMER ON/OFF button to remove the symbol. CHECKING A RECORDING MENU SCREEN 1. Press STOP to switch on the VCR. 2. Press the MENU button. 3. Press [ / ] to select TIMER. Press SET to T I ME R MOD E SE T UP confirm • All the delayed recordings in the VCR’s memory will be shown. : SE L ECT SE T : ENT ER 4.
ADVANCED OPERATION AUDIO AND YOUR VCR HI-FI STEREO SOUND Stereo sound is possible from this VCR if you have a stereo TV connected to the VCR with a scart lead, or audio equipment connected with audio phono leads. The VCR is normally set so that stereo sound is possible. The sound output from the VCR is controlled by the AUDIO OUT button on the remote control. If you wish to change the sound output you can use the AUDIO OUT button as follows: • • • • Press AUDIO OUT once.
ADVANCED OPERATION AUDIO AND YOUR VCR CONNECTING TO AUDIO EQUIPMENT The diagram below shows how to connect your VCR to audio equipment. When connected in this way stereo sound is possible from the speakers.
ADVANCED OPERATION AUDIO DUBBING RECORDING SOUND ON TO A VIDEO TAPE (AUDIO DUBBING) This feature enables you to add narration or background music to a pre-recorded tape. • The audio signal will be recorded on the mono track. The Hi-Fi track will remain unchanged.. If a microphone is to be used, connect it to your audio equipment Connect your audio equipment to AUDIO IN L-R terminals on the front of your VCR. + AUDIO SOURCE 1.
ADVANCED OPERATION AUDIO DUBBING PLAYING BACK AN AUDIO DUBBED TAPE • If you want to listen to the original and the new dubbed audio signal simultaneously, you will need to set AUDIO MIX to ON. • You can change the audio output by pressing the AUDIO OUT button on the remote control. Refer to the table below.
ADVANCED OPERATION DIGITAL DISPLAY TIME OF DAY Shows current time of day, if the clock is set. Press DISPLAY until the time of day appears. For example, 21:20 appears: PR Operation Mode Shows status of tape. Press DISPLAY until the display PR appears, for example: TAPE COUNTER AND ZERO BACK Tape counter measures the current position of the video tape in real time. ZERO BACK uses the tape counter to determine a specific point on a tape you may wish to return to. 1.
ADVANCED OPERATION PLAYBACK OF A VIDEO TAPE CHECKING THE AMOUNT OF TAPE REMAINING When you load a video tape into the VCR it can calculate approximately the amount of video tape remaining in hours and minutes. This is useful in determining whether or not there is sufficient tape left to make a recording. When a video tape is playing, the amount of tape remaining is calculated for you automatically. To display the amount of video tape remaining: 1. Load the video tape into the VCR 2.
ADVANCED OPERATION PLAYBACK OF A VIDEO TAPE PLAYING BACK AN NTSC TAPE NTSC (National Television Standards Committee) is a different TV standard to PAL and is used in some Non-European Countries. Your VCR can playback pre-recorded NTSC tapes onto a PAL system TV, but cannot record an NTSC signal onto a video tape. Note that.. • You cannot record NTSC signals or dub NTSC tapes onto other VCR’s from this VCR.
ADVANCED OPERATION MODE SELECTION Press MENU to display the main menu on the 1. screen. The main menu has four options ME NU including MODE. V I D EOP L U S T I ME R MOD E SE T UP 1. To access the mode menu highlight MODE using the [ : SE L ECT SET : ENT ER / ] buttons, then press SET. ME NU : E X I T 2. Highlight the option to be changed using the [ / ] buttons. Press [ / ] to select AUTO, ON or OFF as appropriate, press SET then MENU to return to the 2.
ADVANCED OPERATION MODE SELECTION 16:9 PLAYBACK AND RECORDING. This feature allows the PLAYBACK and RECORDING of wide screen format signals (16.9) which should automatically change the picture size setting on a wide screen TV. To allow the operation of this feature, ensure 16:9 mode is set to AUTO in the MODE menu. A scart connection must be used between the VCR (SOCKET L1) and the TV. During PLAYBACK of a 16:9 encoded tape the TV should switch to (Widescreen) 16:9 mode.
ADVANCED OPERATION SEARCHING THE VIDEO TAPE SKIP SEARCHING THE VIDEO TAPE You can search the tape in 30 second time intervals. To do this follow the procedure below: 1. Press PLAY/X2 ( ) to start the video tape playing. 2. Press SKIP SEARCH on the remote control. 1 press = 30 seconds 2 presses = 1 minute 3 presses = 1 minute 30 seconds 4 presses = 2 minutes The number of times you press SKIP SEARCH determines the forward search time. • After searching, normal playback will resume automatically.
ADVANCED OPERATION REMOTE CONTROL OPERATION OF TV In addition to operating the VCR the remote control will also operate basic functions on TVs, including brands other than SHARP. SETTING UP THE VCR REMOTE CONTROL TO OPERATE THE TV 1. Switch on the TV. Open the door on the remote control and point the unit at the TV. 2. Hold down TV BRAND SET on the VCR remote control and the appropriate button for the TV from the list shown, for 2 seconds. For example for a SHARP TV, press TV BRAND SET and 1.
ADVANCED OPERATION RECORDING FROM OTHER EQUIPMENT You can record video and audio signals from various sources, for example a camcorder, onto a video tape using your VCR. For example, recording from a camcorder connected to LINE 2 IN/DECODER on your VCR: Optional SCART connection (not supplied). VIDEO AUDIO (L/MONO) AUDIO (R) ANTENNA IN ENTREE ANTENNE G S-VIDEO OUT SORTIE SON S-VIDEO D RF OUT SORTIE ANTENNE Mono/Stereo Camcorder 1. Connect your signal source (e.g. Camcorder, Digital Camera, etc.
ADVANCED OPERATION DECODER SWITCHING OPERATION If you connect a separate decoder to the VCR connected to L2 as previously shown, you will need to set the decoder function to ON in order to record the descrambled signal and/or watch it on your TV. Now, when the VCR receives a scrambled signal it is output via LINE 2 terminal to the decoder. The decoder then outputs the descrambled signal back to LINE 2 terminal and the signal can be recorded.
SPECIAL FEATURES ON YOUR VCR POWERSAVE MODE ENABLING POWERSAVE MODE If you wish to use the POWERSAVE feature, it can be switched on within the Mode Menu Screen, this will automatically disable the STANDBY mode. 1. Press MENU to display the main menu on the screen. MODE MENU SCREEN 2. Press [ / ]to select MODE. CO L OUR B L U E MU T E REPEAT AUD I O M I X 16 : 9 ➝POWE R S A V E 3. Press SET. 4. Press [ 5. Press [ / / ]to select POWERSAVE. ]to select ON.
SPECIAL FEATURES ON YOUR VCR CHILD LOCK You can lock your VCR with this feature. It will work even when the VCR is in POWERSAVE/ STANDBY, preventing children from operating the VCR. TO ENGAGE CHILD LOCK Press and hold on the remote control for about 2 seconds. flashes and then remains lit on the VCR display confirming that CHILD LOCK has been activated. Regardless of what other operating buttons are touched, the VCR will continue to operate in its present mode.
CUSTOMISED INSTALLATION MANUALLY TUNING A CHANNEL • It should not be necessary to tune in a broadcast channel manually except in unusual circumstances such as poor signal. To manually tune in a channel follow the procedure below. 1. Press MENU. 2. Press the / menu select buttons to select SET UP. Press SET to confirm. CHANN E L CHANN E L C L OCK 3. CHANNEL PRESET will be highlighted. Press SET. 4. Press / S E T UP PRE S E T S OR T to select CHANNEL. 5.
CUSTOMISED INSTALLATION MANUALLY TUNING A CHANNEL The VCR has 99 programmable channel positions each of which can be set to any of the broadcast and CATV channels shown in the table. If you select CC on the menu, cable will be tuned first. Note that both cable and non-cable will be tuned regardless of the setting.
CUSTOMISED INSTALLATION INSTALLATION OF A SKY DIGIBOX RECEIVER 1. Connect your Sky Digibox receiver to the VCR as shown in connecting the cables. 2. Place the receiver near the VCR (ideally on the top). This ensures that the reflected infrared signals from the VCR which control the satellite receiver can reach it unimpeded. 3. Ensure the receiver is not in Standby or any special mode. • The preset Sky channels can now be tuned in as part of the installation procedure.
CUSTOMISED INSTALLATION INSTALLATION OF A SKY DIGIBOX RECEIVER SAT CONTROL WILL BE HIGHLIGHTED. SAT RECE I VER Leave SAT CONTROL set to OFF and press SET. S A T CON T RO L SET : ENT ER OF F : CHANGE ME NU : E X I T The VCR will attempt to copy the TV preset list (NexTView, Smart Link, Easy Link and Megalogic compatible TV’s only). During the copying process the display will show the TV presets that are being copied.
CUSTOMISED INSTALLATION INSTALLATION OF A SKY DIGIBOX RECEIVER SKY DIGIBOX INSTALLATION 5. Press MENU. MANUAL TUNI NG S AT RE C E I VER 6. Press [ / ] to select SET UP. Press SET to confirm. S AT PROGRAM S EARCH 7. CHANNEL PRESET will be highlighted. Press SET to confirm. 8. Press [ / ] to select SAT RECEIVER. Press SET to confirm. The satellite receiver screen will appear. SAT RECE I VER / ], to set SAT CONTROL to 10. Press [ / ], to select INPUT. L2 will be highlighted.
CUSTOMISED INSTALLATION INSTALLATION OF A SKY DIGIBOX RECEIVER 13. Press [ / ] to select MANUAL TUNE. MANUAL TUNI NG S AT RE C E I VER S AT PROGRAM S EARCH 14. Press SET to confirm 16. Press [ / Then press [ 17. Then press [ ▲ [ / ] to choose the required VCR preset channel. ST 1 0 6 CH 1 SAT CH 2 1 ▲ ➔P R E S E T SOURC E CHANN E L F I N E T UN I NG D E COD E R SK I P 15. PRESET will be highlighted. Press ON O F F ON O F F ] to select SOURCE. / ] to select SAT. / ] to select CHANNEL.
CUSTOMISED INSTALLATION INSTALLATION OF A SKY DIGIBOX RECEIVER BSKYB DIGITAL CHANNEL MAPPING PRESET NO: 101 102 103 104 105 106 109 110 112 115 118 121 124 127 130 133 136 139 142 145 148 151 160 178 181 301 - 305 308 - 312 315 316 324 401 402 403 410 413 416 440 443 446 PRESET NO: 449 452 501 504 507 508 510 513 533 534 535 550 551 552 558 559 561 564 570 601 602 604 607 610 630 633 636 700 701 - 758 964 965 966 977 980 998 CHANNEL BBC1 BBC2 ITV CH4 CH5 SKY ONE UK GOLD UK GOLD 2 LIVING DISNEY GRANADA PL
CUSTOMISED INSTALLATION MANUALLY SORTING CHANNELS SORTING THE CHANNELS INTO YOUR PREFERRED ORDER When your VCR tunes in broadcast channels automatically it sorts them into a standard order using teletext information. You can change the order of the channels with the following procedure. 1. Press MENU. 2. Press [ / 2. confirm. 3. Press [ MENU SCREEN ] to select SET UP. Press SET to MOD E SE T UP / ] to select CHANNEL SORT. Press SET to confirm. 4. The MOVE position will be highlighted.
CUSTOMISED INSTALLATION MANUALLY SORTING CHANNELS DELETING CHANNELS If there is a channel you wish to delete from the VCR memory you can follow the procedure below. 1. Press MENU. 2. Press [ / 2. ] to select SET UP. Press SET to confirm. 3. Press [ / MENU SCREEN T I ME R MOD E SE T UP ] to select CHANNEL SORT. Press SET to confirm. 4. Press [ / ] to select CANCEL. Press SET to 5. confirm. 1 BBC 1 2 BBC 2 3 CH 5 4 I TV 5 CH 4 6 5. Press [ / / / ] to highlight the channel to be cancelled.
CUSTOMISED INSTALLATION MANUALLY SORTING CHANNELS RE-NAMING CHANNELS When your VCR tunes in broadcast channels automatically, it names them using teletext information. You can change the name of a channel with the following procedure. 1. Press MENU. 2. : MENU SCREEN 2. Press [ / ] to select SET UP. Press SET to confirm. MOD E SE T UP 3. Press [ / ] to select CHANNEL SORT. Press SET to confirm. 5. 4. Press [ / ] to highlight NAME. Press SETto confirm. 1 BBC 1 2 BBC 2 3 I TV 4 CH 7 5 CH 5 6 5.
CUSTOMISED INSTALLATION MANUALLY SETTING THE CLOCK The clock will normally be set using teletext information when your VCR automatically tunes in the broadcast channels. If for any reason teletext signals are not present your VCR will not be able to set the clock. This procedure will allow you to set the clock manually. 1. Press MENU. Press [ / ] to select SET UP. Press SET to confirm. 2. Press [ C L OCK / ] to select CLOCK.
MORE INFORMATION ABOUT YOUR VCR VCR DIGITAL DISPLAY 1 2 3 4 5 6 LR 16 15 S-VHS STOP SP LP ET AM PM 14 PR 7 VCR 8 9 10 V PS P DC DEC 13 12 11 1. AUDIO OUTPUT indicators. 10. DECODER indicator. 2. TIMER indicator. 11. LONG PLAY indicator. 3. PLAY indicator. 12. STANDARD PLAY indicator. 4. RECORDING indicator. 13. CHILD LOCK indicator. 5. STOP indicator. 14. AM/PM indicators. 6. VCR TAPE indicator. 15. S-VHS ET indicator. 7. PRESET indicator. 16. S-VHS indicator 8.
MORE INFORMATION ABOUT YOUR VCR ON-SCREEN DISPLAY All the information you need on the VCR status will be summarised on the on-screen display. If you are recording, playing back a tape or watching a broadcast on the video channel you can call up three standard on-screen displays. The display can be selected by pressing the MODE OSD button on the remote control, 1,2,3 or 4 times. 1. AUTO, the current mode and channel 1. number will be displayed for 3 seconds when an operation or number button is pressed.
MORE INFORMATION ABOUT YOUR VCR MANUFACTURERS CODES FOR SATELLITE RECEIVERS The following table is a list of satellite manufacturers’ code numbers. Your VCR will use one of these in order to recognise your satellite receiver. The code number must be entered at point 11. during installation with a satellite receiver. Look up your make of satellite receiver. Use the NUMBER BUTTONS to enter the first code number listed. For example number 8 should be entered 0 0 8. Continue from point 12. (AUTO INSTALLATION).
MORE INFORMATION ABOUT YOUR VCR SPECIFICATIONS Format: Number of heads: Video signal system:: Hi-Fi audio recording system: Maximum playing time: Tape width: Tape speed: Antenna: Reception channels: RF output signal: Power requirement: Power consumption: Operating temperature: Storage temperature: Video input: Video output: S-Video connections: Audio input: Audio output: Hi-Fi audio: Dimensions: Weight: Supplied accessories: VHS PAL/S-VHS/S-VHS ET standard Six heads PAL colour or monochrome signal: 625
TROUBLESHOOTING TROUBLESHOOTING BEFORE REQUESTING SERVICE! The following conditions do not always denote trouble. Therefore, perform the checks described below before calling for service. If the problem cannot be corrected by the use of this guide, remove the mains plugs from the wall socket and contact the dealer or supplier from whom the unit was purchased in order to obtain service.
TROUBLESHOOTING TROUBLESHOOTING AREA PROBLEM REMOTE CONTROL SATELLITE OTHER PROBLEMS Standard S-VHS S-VHS ET VHS Tape Speed SP LP EP SP LP EP SP LP EP The VCR can not be operated by remote control Satellite receiver does not respond to VCR commands. Desired satellite channel can not be selected by the VCR. POSSIBLE CAUSE/CURE • Remote control is too far away from the main unit. • Point the remote control at the VCR. • Batteries are flat - replace both. • Batteries have not been inserted correctly.
VCR RESET 1. Press the STOP button on the front of the VCR. 2. Press and hold MENU and the CHANNEL ( ✔ / ] buttons together for 10 seconds. VCR RESET IS NOW COMPLETE Please continue with your previous procedure. RF CHANNEL TUNING If you have a preferred RF output channel, this can be set manually (21-69) by following the procedure below: 1. Press the STANDBY button. 2. Press and hold the MENU button on the VCR front panel for 3 seconds. 3.
GUARANTEE SHARP Electronics (UK) Ltd (hereafter called Sharp) guarantee to provide for the repair, or at its option the replacement, of this product subject to the conditions listed below: 1. This guarantee shall only apply to faults which are due to inferior workmanship or materials. It does not cover faults or damage by accident, misuse, fair wear and tear, neglect, tampering with the product, or repair other than by a Service Facility appointed by SHARP. 2.
CONNECTING TO THE MAINS This VCR is suitable only for connection to UK mains. The unit is fitted with a moulded 3-pin mains plug with a 3-amp fuse. The VCR does not have a mains power switch. When connected to the mains, the unit will draw current at all times to power the clock. Be sure to unplug the VCR when it is not to be used for several months. TO REPLACE THE FUSE: You must use a 3-amp fuse, marked ASA (ASTA) or (BSI) to BS-1362. Remove the fuse cover as shown.
CALLING FOR SERVICE ● If you are unable to resolve a problem using the TROUBLESHOOTING guide, do not remove the cabinet or attempt to service this VCR yourself. ● For service please contact your dealer. If this is not possible, please call our Customer Information Centre for details of your nearest Sharp Service Centre. ● Please note that for repairs during the guarantee period, you will need to produce proof of purchase.
