STERN ° HQ (High Quality) * Programmable Remote Control with LGD ® APED VHS Index Search System (Index Search, Interval Search, Counter Search) © Advanced Full Auto Function ¢ Full Auto Play Function o 365-Day, 8-Programmer Timer (Daily/Weekly Programmable) © 5-Digit Lin gar Tape Counter with Memory @ 80-Channel Preset Voltage Synthesized Tuner (CATV Reception) ¢ Tamper-Proof Child Lock ¢ Simple Recording Timer ¢ Loading/Ejecting Cassette by Remote Control ° TV/VGR Control System e B&G Mute Function « Audio
FRONT EJECT button OPERATE button (turns YCR on/off) —— OCR) display work regardless s button.
The remote control lets you operate your VCR at a distance. Just aim the front of the remote control at the Photo receptor window situated on the front panel of your VCR and press the control and timer setting buttons as you would on your VCR. Replacing the Batteries If the remote control does not operate or fails to function normally, replace the batteries. The remote control operates on two R6 (SUBSUME-3, AA) 15 val catteries, available at electronics and camera stores.
@ Set the minuses digits using the + or o button, or using the numeric buttons. (Set 1o 28) Press the CLOG button. “28” lights and 01" of the day’s digits starts flashing. if thee minute is a single digit 9 {zero) must be entered first @ Point the remote control toward the VCR and press the TRANSFER button, © The electronic beep sounds and the multi-function display panel changes to the present time, and the VCR clock starts operating. @ Set the day's digits using the % or .
Channel Skip Canceling Channel Skip: it there are channel positions that are not preset, you can skip them by the @ Select the video channel on your TV. Press the OPERATE button on the following procedure. VCR to ON. © Set the BAND SELECTOR to VHF or UHF. “CH” and the channel position number start flashing. Select the position number whose channel you want to reset using the @ Select the video channel on your TV. Press the OPERATE button on the CHANNEL {A or v} buttons. VCR to ON.
PLAYBACK Slow Playback @ Press the SLOW bunion on the remote control during playback. The picture 1 slow down. To avoid damage to the tape, your VCR will resume normal playback after about five minutes of slow playback. @ If noise bars appear on the screen during slow playback, press the TRACKING ¥ or A button to make them disappear. © Press the PLAY button to resume normal playback. NOTE: + There will be no sound during slow playback.
Tape movement can be confirmed in hours, minutes and seconds with the During simple recording or timer recording the display shows the record finish pay, counter clearing and counter memory are time. operated by the remote control. [RECORD FINISH TIME] [PRESENT TIME] Counter Display € Press the OPERATE butting 1o ON. displayed.) {Ti he present tim © Press the DISPLAY button. (The date is displayed.) [COUNTER] Counter Clear Make sure the counter is displayed, then press the CLEAR button.
(B) INTERVAL SEARCH Programmed are found one afire the other at all index signal locations. @ While the tape is playing or stopped, press the SEARCH Hutton twice, putting the VCR into interval search mode. “IV” flashes. @ Press either the FF (or REW) button. The VCR locate index is forwards {or backwards} IV lights.
e @ Press the PRIG button. “03” is displayed and “DATE’, “DAILY” and “WEEKLY” sitar flashing. Press the DATE {No. 7) button for once only recording, the DAILY (No. 8) button for recording the mass time each day or the WEEKLY (No. 9) button for recording the same time each week. In this example press the DATE (No. 7) bitten. Press the PRIG button. “DATE” is displayed and “10” of the start time flashes. Enter the start time hours {09 using either the buttons to 9) or the ' or = button.
SIMPLE RECORDING TIMER (SRT) Two ways 1o use this SRT for your convenience. g Convenient when having an unexpected visitor or telephone call. * Delay recording: Convenient when leaving the house or going to bed. OPERATE OPERATE CLEAR CHANNEL MME —T @ a2 -STOP Immediate Recording Ending time: 12:30 Channel: 2 {Programmer chandelier) ' @ Select the channel to be recorded. © Tress B {0 start recording and 0 set the desired ending time.
Any selected mode on the VCR can be locked In to prevent accidental change to another mode by simply pressing the C-LOCK bunion on the remote control. All modes remain locked {including power iffy until the child-proof lock is engaged. Press the C-LOCK button on the remote control for about two seconds. fishes on the mutt-function display. & “ew 7 stops Hashing (reaming and the child-proof lock engaged. o © Now regardless of what other operating modes are touched, the video will continue to play the ape.
The following conditions do not always denote trouble. Therefore, perform the checks described barrow before calling for service. doss not light. cassette cannot be . ejected. »VCR does not operate. OPERATE indicator *Tum on power. « Press the TIMER button and disengage the met. inside. Wait for approximately three hours before operating the VCR. » Press the EJECT bunion several rimes. « Safely device in VCR is functioning. Unplug VCR "and plug in again after about one minute.
